17.040 - Linear and angular measurements
ICS 17.040 Details
Linear and angular measurements
Langen- und Winkelmessungen
Mesurage de longueur et mesurage angulaire
Linearne in kotne meritve
General Information
e-Library Subscription
Create subscription and get permanent access to documents within 17.040 - Linear and angular measurements
Currently subscription includes documents marked with .We are working on making all documents available within the subscription.
Specifies general tolerances for linear and angular dimensions and for shape and position of welded structures in four classes, these being based on customary workshop accuracy. The main criterion for the selection of a particular class should be the functional requirements.
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft11 pagesEnglish languagesale 10% offe-Library read for1 day
This document provides the most important design and metrological characteristics of micrometers for external measurements:
— with analogue indication;
— with digital indication: mechanical or electronic digital display.
- Standard22 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft20 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies general tolerances for linear and angular dimensions and for shape and position of welded structures in four tolerance classes, based on customary workshop accuracy. The main criterion for selection of a particular tolerance class is based on the functional requirements which are to be met. The applicable tolerances are always those which are stated in the drawing. Instead of specifying individual tolerances the tolerance classes according to this document can be used. General tolerances for linear and angular dimensions and for shape and position as specified in this document apply for weldments, welding assemblies, welded structures, etc. Special provisions can be necessary for complex structures. The specifications given in this document are based on the independency principle of ISO 8015, according to which the dimensional and geometrical tolerances apply independently of each other. Manufacturing documentation in which linear and angular dimensions or indications for shape and position are presented without individually indicated tolerances shall be deemed incomplete if there is no, or inadequate, reference to general tolerances. This does not apply to temporary dimensions.
- Standard8 pagesEnglish languagesale 15% off
- Standard8 pagesFrench languagesale 15% off
- Draft7 pagesEnglish languagesale 15% off
- Draft7 pagesEnglish languagesale 15% off
- Draft8 pagesFrench languagesale 15% off
This document provides the most important design and metrological characteristics of micrometers for external measurements:
— with analogue indication;
— with digital indication: mechanical or electronic digital display.
- Standard22 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft20 pagesEnglish languagesale 10% offe-Library read for1 day
This document provides the most important design and metrological characteristics of micrometers for external measurements: — with analogue indication; — with digital indication: mechanical or electronic digital display.
- Standard14 pagesEnglish languagesale 15% off
- Standard15 pagesFrench languagesale 15% off
- Draft14 pagesEnglish languagesale 15% off
- Draft14 pagesEnglish languagesale 15% off
- Draft16 pagesFrench languagesale 15% off
This document specifies the rules for geometrical dimensioning and tolerancing of final moulded parts and parts machined out of moulded parts. It also specifies rules and conventions for the indications of these requirements in technical product documentation and specifies the proportions and dimensions of the graphical symbols to be used. This document provides symbols for identifying the relative completeness of the moulded features and parts. These graphical symbols differ from the graphical symbols for surface texture according to ISO 1302[1], which are notably larger. This document specifies general geometrical tolerances using surface profile tolerances related to a general datum system that remains on the final part. It also specifies machining allowances and draft angles (tapers) for castings in all cast metals and their alloys produced by various casting manufacturing processes. This document establishes the general principles for presentation of general geometrical tolerances that apply to 2D technical drawings in all disciplines and trades but which are also applicable to 3D applications. NOTE All figures are shown in 2D views only. When cast datum surfaces are machined, this document is not applicable. [1]Cancelled and replaced by ISO 21920-1.
- Standard50 pagesEnglish languagesale 15% off
- Draft48 pagesEnglish languagesale 15% off
- Draft48 pagesEnglish languagesale 15% off
This new part of ISO 16610 specifies the characteristics of a linear areal spline filter with a global shape retainment. It is the areal extension of the linear profilometric spline filter as specified in ISO 16610-22.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft14 pagesEnglish languagesale 10% offe-Library read for1 day
This Part of EN 13523 describes the procedure for determining objectively the chalking resulting from natural or artificial weathering of an organic coating on a metallic substrate. The advantage of this procedure for measuring chalking of an organic coating is that the result can be read off immediately on an instrument. Subjective judgement by visual comparison of test specimens with referencee specimens is not necessary. Experience to date with this test method has been based mainly on artificially weathered specimens. Reproductible results can only de obtained by careful execution of the test.
- Standard8 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft8 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the general conditions for the thermomechanical analysis of thermoplastics and thermosetting materials, filled or unfilled, in the form of sheet or moulded parts.
Thermomechanical analysis consists of the determination of deformations of a test specimen under constant load as a function of temperature and/or time.
- Standard43 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft35 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the characteristics of a linear areal spline filter with a global shape retainment.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft14 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies general dimensional and geometrical tolerances as well as machining allowance grades for castings using ± tolerances for indicated dimensions as delivered to the purchaser according to ISO/TS 8062-2. It is applicable for tolerancing of dimensions and geometry of castings in all cast metals and their alloys produced by various casting manufacturing processes.
This document does not apply to 3D CAD models used without indicated dimensions.
This document applies to both general dimensional and general geometrical tolerances (referred to in or near the title block of the drawing), unless otherwise specified and where specifically referred to on the drawing by one of the references in Clause 11.
The dimensional tolerances covered by this document are tolerances for linear dimensions.
The geometrical tolerances covered by this document are tolerances for:
— straightness;
— flatness;
— roundness;
— parallelism;
— perpendicularity;
— symmetry;
— coaxiality.
This document does not cover other position tolerances, angular dimensional tolerances or cylindricity tolerances.
This document can be used for the selection of tolerance values for individual indications.
- Standard43 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft35 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the characteristics of a linear areal spline filter with a global shape retainment.
- Standard10 pagesEnglish languagesale 15% off
- Standard10 pagesFrench languagesale 15% off
This document specifies general dimensional and geometrical tolerances as well as machining allowance grades for castings using ± tolerances for indicated dimensions as delivered to the purchaser according to ISO/TS 8062-2. It is applicable for tolerancing of dimensions and geometry of castings in all cast metals and their alloys produced by various casting manufacturing processes. This document does not apply to 3D CAD models used without indicated dimensions. This document applies to both general dimensional and general geometrical tolerances (referred to in or near the title block of the drawing), unless otherwise specified and where specifically referred to on the drawing by one of the references in Clause 11. The dimensional tolerances covered by this document are tolerances for linear dimensions. The geometrical tolerances covered by this document are tolerances for: — straightness; — flatness; — roundness; — parallelism; — perpendicularity; — symmetry; — coaxiality. This document does not cover other position tolerances, angular dimensional tolerances or cylindricity tolerances. This document can be used for the selection of tolerance values for individual indications.
- Standard34 pagesEnglish languagesale 15% off
- Standard34 pagesEnglish languagesale 15% off
- Standard36 pagesFrench languagesale 15% off
This part of ISO 25178 specifies generic procedures for the calibration, adjustment and verification of
areal topography measuring instruments with planar rather than full 3D measurement behaviour and for
the determination of measurement uncertainty components associated with effects on the metrological
characteristics. It considers, what all areal instruments have in common, including. point sensing
instruments with lateral scanning devices. For instrument specific principles, other parts may be
developed in the 700 series of ISO standard 25178. In particular, the calibration of contacting systems
with additional arcuate motion is not covered by this standard and may be described in a future revision
of the ISO 25178-701.
- Standard35 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft37 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies generic procedures for the calibration, adjustment and verification of metrological characteristics that areal topography measuring instruments have in common, as stated in ISO 25178-600.
Because surface profiles can be extracted from surface topography images, most of the methods described in this document can be adapted to profiling instruments.
Instrument-specific issues are not covered by this document. For example, for instruments based on mechanical probing where the probe follows an additional arcuate motion, additional measures are specified in ISO 25178-701.
This document does not include procedures for area-integrating methods, although those are also stated in ISO 25178-6. For example, light scattering belongs to a class of techniques known as area-integrating methods for measuring surface topography.
- Standard35 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft37 pagesEnglish languagesale 10% offe-Library read for1 day
This document defines the concepts of a reference temperature and the standard reference temperature and specifies the standard reference temperature value for the specification of geometrical and dimensional properties of an object. Some examples of geometrical and dimensional properties include size, location, orientation (including angle), form and surface texture of a workpiece.
This document is also applicable to the definition of the measurand used in verification or calibration.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft11 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies generic procedures for the calibration, adjustment and verification of metrological characteristics that areal topography measuring instruments have in common, as stated in ISO 25178-600. Because surface profiles can be extracted from surface topography images, most of the methods described in this document can be adapted to profiling instruments. Instrument-specific issues are not covered by this document. For example, for instruments based on mechanical probing where the probe follows an additional arcuate motion, additional measures are specified in ISO 25178-701. This document does not include procedures for area-integrating methods, although those are also stated in ISO 25178-6. For example, light scattering belongs to a class of techniques known as area-integrating methods for measuring surface topography.
- Standard26 pagesEnglish languagesale 15% off
- Standard28 pagesFrench languagesale 15% off
This document specifies a method for non-destructive measurements of the thickness of conductive coatings on non-conductive base materials. This method is based on the principle of the sheet resistivity measurement and is applicable to any conductive coatings and layers of metal and semiconductor materials. In general, the probe has to be adjusted to the conductivity and the thickness of the respective application. However, this document focuses on metallic coatings on non-conductive base materials (e.g. copper on plastic substrates, printed circuit boards).
This method is also applicable to thickness measurements of conductive coatings on conductive base materials, if the resistivity of the coating and the base material is significantly different. However, this case is not considered in this document.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft13 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a method for non-destructive measurements of the thickness of conductive coatings on non-conductive base materials. This method is based on the principle of the sheet resistivity measurement and is applicable to any conductive coatings and layers of metal and semiconductor materials. In general, the probe has to be adjusted to the conductivity and the thickness of the respective application. However, this document focuses on metallic coatings on non-conductive base materials (e.g. copper on plastic substrates, printed circuit boards).
This method is also applicable to thickness measurements of conductive coatings on conductive base materials, if the resistivity of the coating and the base material is significantly different. However, this case is not considered in this document.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft13 pagesEnglish languagesale 10% offe-Library read for1 day
This Part of EN 13523 specifies a procedure for evaluating the condensation resistance of an organic coating (coil coating) on a metallic substrate, by means of exposure in a humidity cabinet under controlled conditions.
- Standard8 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft8 pagesEnglish languagesale 10% offe-Library read for1 day
This Part of EN 13523 describes the procedure for determining the resistance to water immersion of an organic coating on a metallic substrate. The test is applicable to all kinds of organic coatings, including metallics and embossed, textured, pearlescent and printed coatings. The results of the test give an indication of the resistance of the coil coated metal to water. The method is not intended to reproduce any particular condition of condensation.
- Standard10 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft10 pagesEnglish languagesale 10% offe-Library read for1 day
This Part of EN 13523 specifies a procedure for evaluating the humidity resistance of an organic coating (coil coating) on a metallic substrate, by means of exposure in a humidity cabinet under controlled conditions.
- Standard10 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft10 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the calibration and adjustment of the metrological characteristics of contact (stylus) instruments for the measurement of surface texture by the profile method as defined in ISO 3274. The calibration and adjustment is intended to be carried out with the aid of measurement standards.
Annex B specifies the calibration and adjustment of metrological characteristics of simplified operator contact (stylus) instruments which do not conform with ISO 3274.
- Standard29 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft23 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies parameters for the determination of surface texture by areal methods.
- Standard73 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft59 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies terms, definitions and parameters for the determination of surface texture by profile methods.
NOTE 1 The main changes to previous ISO profile documents are described in Annex I.
NOTE 2 An overview of profile and areal standards in the GPS matrix model is given in Annex J.
NOTE 3 The relation of this document to the GPS matrix model is given in Annex K.
- Standard87 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard87 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft64 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the rules for indication of surface texture by profile methods in technical product documentation by means of graphical symbols.
This document does not cover population requirements.
NOTE See ISO 18391 for population (batch) specifications.
- Standard58 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft58 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the complete specification operator for surface texture by profile methods.
- Standard37 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft25 pagesEnglish languagesale 10% offe-Library read for1 day
This document defines the concepts of a reference temperature and the standard reference temperature
and specifies the standard reference temperature value for the specification of geometrical and
dimensional properties of an object. Some examples of geometrical and dimensional properties include
size, location, orientation (including angle), form and surface texture of a workpiece.
This document is also applicable to the definition of the measurand used in verification or calibration.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft11 pagesEnglish languagesale 10% offe-Library read for1 day
This document defines the concepts of a reference temperature and the standard reference temperature and specifies the standard reference temperature value for the specification of geometrical and dimensional properties of an object. Some examples of geometrical and dimensional properties include size, location, orientation (including angle), form and surface texture of a workpiece. This document is also applicable to the definition of the measurand used in verification or calibration.
- Standard6 pagesEnglish languagesale 15% off
- Standard6 pagesFrench languagesale 15% off
This document specifies test methods for determining the slip resistance of surfaces used by pedestrians.
NOTE It is also possible to use this document for measurements where persons might walk on trafficked areas.
- Standard53 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft54 pagesEnglish languagesale 10% offe-Library read for1 day
This document establishes definitions and evaluation methods for wheel-rail contact geometry parameters influencing the vehicle running dynamic behaviour:
- the rolling radius difference between the two wheels of a wheelset (Δr-function) which serves as a basis for all further calculations;
- the equivalent conicity function from which are derived:
- a single equivalent conicity value for a specified amplitude which is relevant for the assessment of vehicle running stability on straight track and in very large radius curves according to EN 14363;
- the nonlinearity parameter which characterizes the shape of this function and is related to the vehicle behaviour particularly in the speed range close to the running stability limit;
- the rolling radii coefficient which is used to describe the theoretical radial steering capability of a wheelset in a curved track.
Additional information is given about the relationship between the contact angles of the two wheels of a wheelset (Δtanγ-function) and about the roll angle parameter.
NOTE Out of the presented parameters only those related to the contact angle are relevant for independently rotating wheels of wheel pairs.
Descriptions of possible calculation methods are included in this document. Test case calculations are provided to achieve comparable results and to check the proper implementation of the described algorithms.
To validate alternative methods not described in this document acceptance criteria are given for the equivalent conicity function. This includes reference profiles, profile combinations, tolerances and reference results with tolerance limits.
This document also includes minimum requirements for the measurement of wheel and rail profiles as well as of the parameters needed for the transformation into a common coordinate system of right- and left-hand profiles.
This document does not define limits for the wheel-rail contact geometry parameters and gives no tolerances for the rail profile and the wheel profile to achieve acceptable results.
For the application of this document some general recommendations are given.
- Standard140 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft135 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the acceptance tests for verifying the performance of an optical 3D coordinate measuring system (CMS) when measuring lengths as stated by the manufacturer. It also specifies the reverification tests that enable the user to periodically reverify the performance of the optical 3D CMS.
This document is applicable to verification of the measuring performance of CMSs if the surface characteristics (e.g. glossiness, colour) of the object to be scanned are restricted and within a cooperative range.
This document does not apply to other types of CMSs, including those covered by the other parts of the ISO 10360 series.
- Standard62 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft57 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the acceptance tests for verifying the performance of a laser tracker by measuring calibrated test lengths, according to the specifications of the manufacturer. It also specifies the reverification tests that enable the user to periodically reverify the performance of the laser tracker. The acceptance and reverification tests given in this document are applicable to laser trackers utilizing a retroreflector, or a retroreflector in combination with a stylus or optical distance sensor, as a probing system. Laser trackers that use interferometric measurement (IFM), absolute distance measurement (ADM) or both can be verified using this document. This document can also be used to specify and verify the relevant performance tests of other spherical coordinate measurement systems that use cooperative targets, such as “laser radar” systems.
NOTE Systems which do not track the target, such as laser radar systems, will not be tested for probing performance.
This document does not explicitly apply to measuring systems that do not use a spherical coordinate system. However, interested parties can apply this document to such systems by mutual agreement.
This document specifies:
— performance requirements that can be assigned by the manufacturer or the user of the laser tracker;
— the manner of execution of the acceptance and reverification tests to demonstrate the stated requirements;
— rules for proving comformity;
— applications for which the acceptance and reverification tests can be used.
- Standard54 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft48 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a destructive method for the measurement of the local thickness of metallic
and other inorganic coatings by examination of cross-sections with a scanning electron microscope
(SEM). The method is applicable for thicknesses up to several millimetres, but for such thick coatings it
is usually more practical to use a light microscope (see ISO 1463). The lower thickness limit depends on
the achieved measurement uncertainty (see Clause 10).
NOTE The method can also be used for organic layers when they are neither damaged by the preparation of
the cross-section nor by the electron beam during imaging.
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft16 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the calibration and adjustment of the metrological characteristics of contact (stylus) instruments for the measurement of surface texture by the profile method as defined in ISOÂ 3274. The calibration and adjustment is intended to be carried out with the aid of measurement standards.
Annex B specifies the calibration and adjustment of metrological characteristics of simplified operator contact (stylus) instruments which do not conform with ISO 3274.
- Standard26 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft20 pagesEnglish languagesale 15% off
This document provides background information regarding the changes from EN 15302:2008+A1:2010 to the revised version dated 2021, including the reasons for decisions and additional explanation and guidance that is not appropriate in the standard.
The range of equivalent conicity results obtained with different software tools is described. The additional wheel-rail contact parameters, rolling radii coefficient and nonlinearity parameter, are explained. More information is also provided on the different calculation methods and the updated reference profiles for the assessment. The influence of simplifications used in determination of equivalent conicity is discussed.
To provide more information on the importance of considering the complete measurement and calculation process, methods for plausibility checks, eliminating outliers and assessing the uncertainty and repeatability of measurements are included as well as assessments of the smoothing process.
Guidance is given on fields of application of the wheel-rail contact parameters, on the selection of appropriate reference profiles (choice of reference rail profile and rail inclination for assessing wheel profiles and vice versa) and on handling special cases.
As some references in EN 14363 to wheel-rail contact test conditions have caused difficulties in understanding, clarifications issued by ERA are mentioned.
Interpretation of equivalent conicity results, using tools such as conicity maps, is discussed and various approximations such as ‘quick conicity’ assessments are also described.
Information is included on possible additional wheel-rail contact parameters, not yet ready for standardization, but where further experience is needed.
NOTE In this document the commonly used term “wheel-rail contact geometry” is used as a synonym for the more precise term “wheelset-track contact geometry”.
- Technical report87 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft84 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the complete specification operator for surface texture by profile methods.
- Standard37 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft25 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies parameters for the determination of surface texture by areal methods
- Standard73 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft59 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the rules for indication of surface texture by profile methods in technical
product documentation by means of graphical symbols.
This document does not cover population requirements.
NOTE See ISO 18391 for population (batch) specifications.
- Standard58 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft58 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the calibration and adjustment of the metrological characteristics of contact
(stylus) instruments for the measurement of surface texture by the profile method as defined in
ISO 3274. The calibration and adjustment is intended to be carried out with the aid of measurement
standards.
Annex B specifies the calibration and adjustment of metrological characteristics of simplified operator
contact (stylus) instruments which do not conform with ISO 3274.
- Standard29 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft23 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies terms, definitions and parameters for the determination of surface texture by
profile methods.
NOTE 1 The main changes to previous ISO profile documents are described in Annex I.
NOTE 2 An overview of profile and areal standards in the GPS matrix model is given in Annex J.
NOTE 3 The relation of this document to the GPS matrix model is given in Annex K.
- Standard87 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard87 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft64 pagesEnglish languagesale 10% offe-Library read for1 day
Defines terms and parameters used for determining surface texture by the motif method. It also describes the corresponding ideal operator and measuring conditions.
- Corrigendum3 pagesEnglish languagesale 10% offe-Library read for1 day
Defines terms and parameters used for determining surface texture by the motif method. It also describes the corresponding ideal operator and measuring conditions.
- Standard30 pagesEnglish languagesale 10% offe-Library read for1 day
Defines terms and parameters used for determining surface texture by the motif method. It also describes the corresponding ideal operator and measuring conditions.
- Standard30 pagesEnglish languagesale 10% offe-Library read for1 day
This document defines the maximum material requirement (MMR), the least material requirement (LMR) and the reciprocity requirement (RPR). These requirements can only be applied to linear features of size of cylindrical type or two parallel opposite planes type.
These requirements are often used to control specific functions of workpieces where size and geometry are interdependent, for example to fulfil the functions “assembly of parts” (for MMR) or “minimum wall thickness” (for LMR). However, the MMR and LMR can also be used to fulfil other functional design requirements.
- Standard63 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft67 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies parameters for the determination of surface texture by areal methods.
- Standard68 pagesFrench languagesale 15% off
- Standard68 pagesFrench languagesale 15% off
- Draft63 pagesEnglish languagesale 15% off
This document specifies the rules for indication of surface texture by profile methods in technical product documentation by means of graphical symbols. This document does not cover population requirements. NOTE See ISO 18391 for population (batch) specifications.
- Draft47 pagesEnglish languagesale 15% off
This document specifies terms, definitions and parameters for the determination of surface texture by profile methods. NOTE 1 The main changes to previous ISO profile documents are described in Annex I. NOTE 2 An overview of profile and areal standards in the GPS matrix model is given in Annex J. NOTE 3 The relation of this document to the GPS matrix model is given in Annex K.
- Standard78 pagesEnglish languagesale 15% off
- Standard82 pagesFrench languagesale 15% off
- Draft79 pagesEnglish languagesale 15% off
This document specifies the complete specification operator for surface texture by profile methods.
- Draft29 pagesEnglish languagesale 15% off
This document specifies the calibration and adjustment of the metrological characteristics of contact (stylus) instruments for the measurement of surface texture by the profile method as defined in ISO 3274. The calibration and adjustment is intended to be carried out with the aid of measurement standards. Annex B specifies the calibration and adjustment of metrological characteristics of simplified operator contact (stylus) instruments which do not conform with ISO 3274.
- Standard26 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft20 pagesEnglish languagesale 15% off