This document specifies the technical conditions for inspection and delivery of wrought magnesium and magnesium alloy rods/bars and tubes for general engineering applications. It is applicable to wrought magnesium and magnesium alloy extruded round, square and hexagonal rods/bars and seamless round tubes (hereafter referred to as "tubes").

  • Standard
    13 pages
    English language
    sale 15% off
  • Draft
    13 pages
    English language
    sale 15% off

This European Standard establishes temper designations for all forms of wrought aluminium and aluminium alloys and for continuously cast aluminium and aluminium alloys drawing stock and strip intended to be wrought.
NOTE   Some of these temper designations may be subject of patent or patent applications and their listing herein is not to be construed in any way as the granting of a license under such patent right.
Additional temper designations, conforming to this standard, may be standardized with CEN/TC 132 and AECMA/5 provided:
-   the temper is used or is available for use by more than one user;
-   mechanical property limits are defined;
-   the characteristics of the temper are significantly different from those of all other tempers which have the same sequence of basic treatments and for which designations already have been assigned for the same alloy and product;
-   the following are also defined if characteristics other than mechanical properties are considered significant:
a)   test methods and limits for the characteristics; or
b)   the specific practices used to produce the temper.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the terminology, requirements and test methods for metal coil, strip, and flat sheets and factory made pieces intended for fully supported applications in roofing and wall cladding or lining. It does not apply to products manufactured on site.
This European Standard covers fully-supported aluminium, copper, lead, steel, stainless steel and zinc products with or without coatings, e.g. metallic, organic, inorganic or multi-layer (see Annex A).
This European Standard also includes rules for marking, labelling and evaluation of conformity.
Requirements concerning acoustical and insulation properties are not considered in this European Standard.
This European Standard does not include calculation or design requirements with regards to the works, installation techniques or the performance of the installed products.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1   This European Standard covers the grades of wrought steels and alloys listed in Table 1 and Table 2, which are usually employed for components and equipment, for which the main requirement is their creep resistance under mechanical long-time stressing at temperatures above 500 C.
NOTE   Heat resisting grades given in EN 10095 [9] may also be used for similar applications if so agreed.
1.2   This European Standard specifies the technical delivery conditions for semi-finished products, for hot or cold rolled sheet/plate and strip, hot or cold formed (cold drawn) bars, rods, wire and sections.
1.3   The general technical delivery conditions specified in EN 10021:2006 apply in addition to the specifications of this European Standard, unless otherwise specified in this European Standard.
1.4   This European Standard does not apply to components manufactured by further processing the product forms listed in 1.2 with quality characteristics altered as a result of such further processing.
1.5   This European Standard shall not be used for aerospace and pressure purposes.
1.6   For steels and alloys with similar chemical composition, but intended for different applications, see the Bibliography.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the terminology, requirements and test methods for factory made self-supporting metal sheets and tiles (for non-structural applications) delivered in the form of manufactured pieces for roofing and wall cladding and lining.
This standard also covers ceiling (including internal metal sheet) and soffit applications and cassettes (see Figure 1).
This standard covers self-supporting copper, zinc, steel, aluminium and stainless steel sheet with or without coatings, e.g. metallic, organic, inorganic or multi-layer (see Annex A). A moisture retaining layer may be present on the reverse side of the product.
This standard also includes rules for marking, labelling and evaluation of conformity.
This standard does not cover products for structural purposes, i.e. it does not cover products intended to contribute to the global or partial stability of the building structure by providing racking resistance or resistance to permanent static loads (excluding self-weight of the metal sheet).
Requirements concerning acoustical and thermal insulation properties are not considered in this standard.
This standard does not include calculation or design requirements with regards to the works, installation techniques or the performance of the installed products.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1   This European Standard specifies the different types of inspection documents supplied to the purchaser, in accordance with the requirements of the order, for the delivery of all metallic products e.g. plates, sheets, bars, forgings, castings, whatever their method of production.
1.2   This standard may also apply to non-metallic products.
1.3   This standard is used in conjunction with the product specifications which specify the technical delivery conditions of the products.
NOTE 1   The list of information that may be included in the inspection documents can be found in appropriate documents, e.g. prEN 10168 for steel.
NOTE 2   Annex A gives a summary of the different inspection documents.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    9 pages
    German language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    9 pages
    German language
    sale 10% off
    e-Library read for
    1 day

Covers non-ferrous metallic pneumatic cylinder tubes. Defines the mechanical properties, dimensional tolerances, surface finishes, and technical delivery conditions of the following tubes and bores for pneumatic fluid power cylinders: round non-ferrous metallic tubes, seamless or welded type, in the as-drawn stress-relieved or fully heat-treated condition; bores, specially finished, with or without metal removal. Annex A specifies the dimensions and tolerances on inside diameters, annex B provides a recommended method of ordering.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    6 pages
    French language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off

Covers non-ferrous metallic pneumatic cylinder tubes. Defines the mechanical properties, dimensional tolerances, surface finishes, and technical delivery conditions of the following tubes and bores for pneumatic fluid power cylinders: round non-ferrous metallic tubes, seamless or welded type, in the as-drawn stress-relieved or fully heat-treated condition; bores, specially finished, with or without metal removal. Annex A specifies the dimensions and tolerances on inside diameters, annex B provides a recommended method of ordering.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    6 pages
    French language
    sale 15% off
  • Standard
    6 pages
    French language
    sale 15% off

This European Standard specifies the terminology, requirements and test methods for factory made self-supporting metal sheets and tiles (for non-structural applications) delivered in the form of manufactured pieces for roofing and wall cladding and lining.
This standard also covers curved sheets, sheets intended to be used with insulation and membranes, ceiling products (including internal metal sheet) and soffit products  and cassettes (see Figure 1).
This standard covers self-supporting copper, zinc, steel, aluminium and stainless steel sheet with or without coatings, e.g. metallic, organic, inorganic or multi-layer (see Annex A). A moisture retaining layer intended to reduce the fall of droplets coming from condensation may be present on the reverse side of the product.
This standard does not cover products for structural purposes, i.e. it does cover products used in constructions of Class III (according to EN 1993 1 3), it does not cover products used in constructions of Classes I and II (according to EN 1993 1 3] intended to contribute to the global or partial stability of the building structure by providing racking resistance.
Requirements concerning acoustical and thermal insulation properties are not considered in this draft standard.
This standard does not include calculation or design requirements with regards to the works, installation techniques or the performance of the installed products.

  • Draft
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard establishes temper designation for all forms of wrought aluminium and aluminium alloys and to continuously cast aluminium alloy drawing stock and strip intended to be wrought.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the terminology, requirements and test methods for metal coil, strip, and flat sheets and factory made pieces intended for fully supported applications in roofing and wall cladding or lining. It does not apply to products manufactured on site.
This European Standard covers fully-supported aluminium, copper, lead, steel, stainless steel and zinc products with or without coatings, e.g. metallic, organic, inorganic or multi-layer (see Annex A).
This European Standard also includes rules for marking, labelling and evaluation of conformity.
Requirements concerning acoustical and insulation properties are not considered in this European Standard.
This European Standard does not include calculation or design requirements with regards to the works, installation techniques or the performance of the installed products.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day

DIN - Corrected Table 2 in German version

  • Corrigendum
    2 pages
    German language
    sale 10% off
    e-Library read for
    1 day

1.1   This European Standard covers the grades of wrought steels and alloys listed in Tables 1 and 2 which are usually employed for components and equipment, for which the main requirement is their creep resistance under mechanical long-time stressing at temperatures above 500 °C.
Also heat resisting grades given in EN 10095 may be used for similar applications if so agreed.
1.2   This European Standard specifies the technical delivery conditions for semi-finished products, for hot or cold rolled sheet/plate and strip, hot or cold formed (cold drawn) bars, rods, wire and sections.
1.3   The general technical delivery conditions specified in EN 10021 apply in addition to the specifications of this European Standard, unless otherwise specified in this European Standard.
1.4   This European Standard does not apply to components manufactured by further processing the product forms listed in 1.2 with quality characteristics altered as a result of such further processing.
1.5   This European Standard is not intended for aerospace and pressure purposes.
1.6   For steels and alloys with similar chemical composition, but intended for different applications, see the Bibliography.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    2 pages
    French language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of ISO 3134 defines terms relating to wrought products (rod/bar, wire, tube, profile, sheet, strip, forging), produced by hot and/or cold plastic deformation processes (such as extruding, forging, hot rolling, cold rolling or drawing). An annex gives explaining notes to some definitions.

  • Standard
    12 pages
    English language
    sale 15% off

This part of ISO 3134 defines relating to materials special terms to aluminium and aluminium alloys and general terms such as alloy, alloying element, impurity, wrought alloy, casting alloy, master alloy, heat-treatable alloy etc. Magnesium and magnesium alloys will be classified to a later time.

  • Standard
    12 pages
    English language
    sale 15% off

This part of ISO 3134 defines following terms: unwrought product, ingot for rolling, ingot for extruding, ingot for forging, ingot for remelting.

  • Standard
    12 pages
    English language
    sale 15% off

This part of ISO 3134 defines terms relating to castings (to sand casting, permanent mould casting, pressure die casting and centrifugal casting).

  • Standard
    12 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    2 pages
    French language
    sale 15% off