This document specifies the test requirements and the test methods for extruded thermoplastic tubing and hoses for use in vehicles powered by internal-combustion engines, excluding use in air braking systems (see ISO 7628), fuel lines (see ISO 13775-2), and high-pressure hydraulic systems. This document is intended especially for use by original equipment manufacturers (OEMs).

  • Standard
    13 pages
    English language
    sale 15% off
  • Draft
    13 pages
    English language
    sale 15% off

ISO 4081:2016 specifies the requirements for straight or pre-formed rubber hoses and tubing for use in pressurized or unpressurized cooling circuits containing 1,2-ethanediol-based coolants in internal-combustion engines for vehicles with an unladen mass (as defined in ISO 1176) of 3,5 t or less. In addition, this specification may also be applied as a classification system to enable original equipment manufacturers (OEMs) to detail a "line call-out" of tests for specific applications where these are not covered by the main types specified (see example in Annex D). In this case, the hose or tubing would not carry any marking showing this ISO specification number but may detail the OEM's own identification markings as shown on their part drawings.

  • Standard
    15 pages
    English language
    sale 15% off

ISO 17324:2014 specifies requirements of rubber hoses used in the automotive turbocharger system to connect turbocharger, intercooler, and internal combustion engine at the working temperatures from −40°C to +250°C and the working pressures from −0,01MPa(−0,1bar) to 0,5MPa(5bar). Hoses covered by ISO 17324:2014 may be straight or shaped.

  • Standard
    15 pages
    English language
    sale 15% off

ISO/TS 18571:2014 provides validation metrics and rating procedures to be used to calculate the level of correlation between two non-ambiguous signals obtained from a physical test and a computational model, and is aimed at vehicle safety applications. The objective comparison of time-history signals of model and test is validated against various loading cases under different types of physical loads such as forces, moments, and accelerations. However, other applications might be possible too, but are not within the scope of ISO/TS 18571:2014.

  • Technical specification
    62 pages
    English language
    sale 15% off

This document provides the design for an LNG (un)loading connector between LNG road tanker and LNG fuelling stations. This document can be also used for LNG rail tenders. This document includes requirements for (at least):
-   functional description of the LNG Unloading Receptacle and LNG Unloading Nozzle;
-   technical layout description of the LNG Unloading Receptacle.
The technical layout description of the LNG Unloading Nozzle is not part of this document.
The basic functional requirement of the LNG unloading connector are as follows:
-   to prevent leakage of methane during operation and in particular during disconnecting;
-   easy handling, no spillage and purging with nitrogen during disconnecting.
The loading connector between the LNG road tanker and the LNG terminal is not covered by this document.
See Figure 1.
[Figure not represented]
Figure 1 - Scope of the document

  • Draft
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the minimum requirements for the unloading stop system of the unloading of LNG from an LNG road tanker to the LNG fuelling station. This document consists of two main topics:
-   functional description of the unloading stop system;
-   technical layout description of the unloading stop system.

  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 13775-1:2015 specifies the test requirements and the test methods for extruded thermoplastic tubing and hoses for use in vehicles powered by internal-combustion engines, excluding use in air braking systems (see ISO 7628), fuel lines (see ISO 13775‑2), and high-pressure hydraulic systems. This part of ISO 13775 is intended especially for use by original equipment manufacturers (OEMs).

  • Standard
    13 pages
    English language
    sale 15% off

ISO 4081:2010 specifies the requirements for straight or pre-formed rubber hoses and tubing for use in pressurized or unpressurized cooling circuits containing 1,2-ethanediol-based coolants in internal-combustion engines for vehicles with an unladen mass (as defined in ISO 1176) of 3,5 t or less. In addition, this specification may also be applied as a classification system to enable original equipment manufacturers (OEMs) to detail a “line call-out” of tests for specific applications where these are not covered by the main types specified. In this case, the hose or tubing would not carry any marking showing this ISO specification number but may detail the OEM's own identification markings as shown on their part drawings.

  • Standard
    12 pages
    English language
    sale 15% off
  • Standard
    14 pages
    English language
    sale 15% off

ISO 4081:2005 specifies the requirements for straight or pre-formed rubber hoses and tubing for use in pressurized or unpressurized cooling circuits containing 1,2-ethanediol-based coolants in internal-combustion engines for vehicles with an unladen mass of 3,5 t or less. In addition, this specification may also be applied as a classification system to enable original equipment manufacturers (OEMs) to detail a 'line call-out' of tests for specific applications where these are not covered by the main types specified. In this case, the hose or tubing would not carry any marking showing this ISO specification number but may detail the OEM's own identification markings as shown on their part drawings.

  • Standard
    12 pages
    English language
    sale 15% off