The document establishes an agreed method for evaluation of pull through resistance (tension/compression for fasteners through the sheets), shear resistance, bending strength and bending modulus of elasticity and suggests an approved safety concept of fibre-cement flat sheets for internal and external wall and ceiling finishes based on the experiences obtained over the last number of years in different countries. The results are only applicable to the fibre-cement product and not to the complete fixing assembly.
NOTE 1   For design purposes of fibre-cement flat sheets in the final application, the failure modes pull-out and breaking of the fixing or substructure are not in the scope of this standard. They might become decisive and need to be tested or calculated according to the relevant design standards for fixings (e.g. EN 14592) or ETA and substructure (e.g. Eurocode 3 for steel, Eurocode 5 for wood and Eurocode 9 for aluminium substructures) and compared with the results for pull-through and shear resistance.
The results are also applicable for:
—   Coated or uncoated sheets manufactured at the same production facility as the tested sheets provided that the sheets are of the same type, have at least the same declared class according to EN 12467:2012+A2:2018, Table 6 and at least the same nominal thickness.
—   The test method can be applied to textured or non-textured fibre-cement flat sheets. The results of non-textured sheets are only applicable for textured sheets if the nominal minimum thickness of the textured sheet is at least the nominal thickness of the non-textured sheet.
—   The same type of fixing head or washer assembly where applicable if the diameter of the fixing head or washer is 0 mm to 2 mm larger than in the test.
—   The Shore A hardness of the sealing washer, where applicable, is ± 5 that of the washer used in the test, given that the washer thickness is at least as thick, the washer material at least as strong and the shape (dome or flat) of the washer equal to what has been tested.
NOTE 2   
A)   For pull-through resistance, if the diameter of the drilled hole through the fibre-cement sheet is 0 mm to 2 mm smaller or equal than in the test up to the diameter of the shank of the fastener, providing, during the test there is the required clearance hole around the shank of the fastener.
B)   For shear resistance, if the diameter of the drilled hole is equal to what has been tested.
It applies only to products as delivered.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies test methods for pull through (tension/compression testing for fasteners through the sheets) and shear resistance of fibre-cement profiled sheets according to EN 494. The results are only applicable to the fibre-cement product and not to the complete fixing assembly.
It applies only to products as delivered.
The field of application for pull through resistance is defined in 7.6.
The field of application for shear resistance is defined in 8.6.
NOTE   For design purposes of fibre-cement profiled sheets in the final application, the failure modes pull-out and breaking of the fixings or substructure are not in the scope of this standard. They might become decisive and need to be tested or calculated according to the relevant design standards for fixings (e.g. Eurocode 3 for steel, Eurocode 5 for wood and Eurocode 9 for aluminium substructures) and compared with the results for pull-through and shear resistance.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies a test method for pull through and shear resistance of fibre-cement flat sheets for roofing and cladding.
The results are also applicable for:
-   Coated or uncoated sheets manufactured at the same production facility as the tested sheets.
-   The test method can be applied to textured or non-textured fibre-cement flat sheets. The results of non-textured sheets are only applicable for textured sheets if the nominal minimum thickness of the textured sheet is at least the nominal thickness of the non-textured sheet.
-   The same type of fixing head or washer assembly where applicable if the diameter of the fixing head or washer is 0 mm to 2 mm larger than in the test.
-   The Shore A hardness of the sealing washer, where applicable, is ± 5 that of the washer used in the test.
-   The diameter of the drilled hole through the fibre cement sheet is 0 mm to 2 mm smaller than in the test, providing there is the required clearance hole around the shank of the fastener.
It applies only to products as delivered.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies test methods for pull through resistance and shear resistance of fibre-cement profiled sheets for roofing and cladding. The results are only applicable to the fibre cement product and not to the complete fixing assembly.
It applies only to products as delivered.
The field of application for pull through resistance is defined in 7.6.
The field of application for shear resistance is defined in 8.6.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the technical requirements and establishes methods of inspection and test as well as acceptance conditions for fibre-cement flat sheets, siding shingles and planks (referred to as sheets later in this document) for one or more of the following uses:
-   internal wall and ceiling finishes;
-   external wall and ceiling finishes.
Products covered by this European Standard can be used for other purposes provided they comply with the relevant application standard, e.g. rigid underlays.
This European Standard covers sheets reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not cover sheets for fire protection purposes.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.

  • Standard
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement slates and their fibre-cement fittings for one or more of the following uses:
-   roofing;
-   internal wall finishes;
-   external wall and ceiling finishes.
This European Standard applies to fibre-cement slates with a height dimension h (see Clause 4) not exceeding 850 mm for overlapping assembly. For the purpose of this European Standard, fibre-cement slates have been classified according to their bending moment.
This European Standard covers fibre-cement slates reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed products.

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement slates and their fibre-cement fittings for one or more of the following uses:
-   roofing;
-   internal wall finishes;
-   external wall and ceiling finishes.
This European Standard applies to fibre-cement slates with a height dimension h (see Clause 4) not exceeding 850 mm for overlapping assembly. For the purpose of this European Standard, fibre-cement slates have been classified according to their bending moment.
This European Standard covers fibre-cement slates reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed products.

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the technical requirements and establishes methods of inspection and test as well as acceptance conditions for fibre-cement flat sheets, siding shingles and planks (referred to as sheets later in this document) for one or more of the following uses:
-   internal wall and ceiling finishes;
-   external wall and ceiling finishes.
Products covered by this European Standard can be used for other purposes provided they comply with the relevant application standard, e.g. rigid underlays.
This European Standard covers sheets reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not cover sheets for fire protection purposes.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.

  • Standard
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement profiled sheets and their fibre-cement fittings for one or more of the following uses:
-   roofing;
-   internal wall finishes;
-   external wall and ceiling finishes.
For the purpose of this European Standard, fibre-cement profiled sheets are classified according to their height of corrugation and their mechanical characteristics.
This European Standard covers fibre-cement profiled sheets reinforced with fibres of different type as specified in 5.1.1, with and without factory applied coating.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.
NOTE   Some of these requirements can be applied, after agreement, to curved sheets for specific applications.

  • Standard
    71 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 8336:2017 specifies methods for the inspection and testing of fibre-cement flat sheets and provides the acceptance conditions for their use in one or more of the following applications: - external wall and ceiling finishes; - internal wall and ceiling finishes; - internal and external backing sheets. Products covered by this document can be used for other purposes, provided they comply with the appropriate national or international application code or standard. NOTE 1 ISO 8336:2017 does not apply to sheets for fire protection purposes. NOTE 2 ISO 8336:2017 does not include calculations for installation design requirements, wind uplift or water proofing of the installed sheets. NOTE 3 ISO 8336:2017 does not apply to the following products: - boards of Portland or equivalent cement reinforced with fibrous wood particles; - fibre-reinforced boards of calcium silicate or cement for thermal insulation or fire protection; - sheets containing asbestos fibre reinforcement; - sheets containing steel fibre reinforcement; - fibre-cement roofing slates.

  • Standard
    47 pages
    English language
    sale 15% off

This European Standard specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement profiled sheets and their fibre-cement fittings for one or more of the following uses:
-   roofing;
-   internal wall finishes;
-   external wall and ceiling finishes.
For the purpose of this European Standard, fibre-cement profiled sheets are classified according to their height of corrugation and their mechanical characteristics.
This European Standard covers fibre-cement profiled sheets reinforced with fibres of different type as specified in 5.1.1, with and without factory applied coating.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.
NOTE   Some of these requirements can be applied, after agreement, to curved sheets for specific applications.

  • Standard
    71 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 10904:2011 specifies technical requirements and methods for the inspection and testing of straight short and long fibre-cement profiled sheets and their fibre-cement fittings designed to provide the weather-exposed surfaces on roofs and internal and external walls of buildings. Products covered by ISO 10904:2011 can be used for other purposes, provided they comply with the appropriate national or international application code or standard. Some of the requirements of ISO 10904:2011 can apply, after agreement between manufacturer and purchaser, to curved profiled sheets. The type tests described in ISO 10904:2011 are not intended to evaluate the performance of the coating in isolation (color fastness, adhesion, etc.). Specific performance requirements for coatings are referenced in other International Standards or national standards. ISO 10904:2011 does not apply to fibre-cement profiled sheets and fittings reinforced with asbestos fibres.

  • Standard
    53 pages
    English language
    sale 15% off

ISO 9125:2009 specifies technical requirements and methods for the inspection and testing of fibre-cement slates and shingles and their fibre-cement fittings, designed to protect the weather-exposed surfaces on roofs and claddings of buildings. Products covered by ISO 9125:2009 can be used for other purposes provided they comply with the appropriate national or international application code or standard. ISO 9125:2009 applies to fibre-cement slates with a height dimension not exceeding 850 mm for overlapping assembly. The type tests described in ISO 9125:2009 are not intended to evaluate the performance of the coating in isolation (colour fastness, adhesion, etc.). Specific performance requirements for coatings are referenced in other ISO or national standards. ISO 9125:2009 does not apply to fibre-cement slates reinforced with asbestos fibres. ISO 9125:2009 does not include calculations for installation requirements, wind uplift or rain proofing of the installed products. National standards for installation requirements can be adopted.

  • Standard
    40 pages
    English language
    sale 15% off

This European Standard specifies a test method for identifying, for a given GRC formulation (constituents and their proportions in the formulation), the effect of environmental factors such as water and temperature on the change of mechanical characteristics. For other conditions of exposure, e.g. where freezing, thawing and action of thawing salt occurs, the test will be adapted.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a soft body impact test method for fibre-cement profiled sheets for roofing.
This European Standard applies to fibre-cement profiled sheets conforming to EN 494 and of length greater than or equal to 1,04 m.
It applies only to products as delivered.
NOTE   This European Standard can be applied, after agreement between manufacturer and purchaser, to curved sheets.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies a soft body impact test method for fibre-cement profiled sheets for roofing.
This European Standard applies to fibre-cement profiled sheets conforming to EN 494 and of length greater than or equal to 1,04 m.
It applies only to products as delivered.
NOTE   This European Standard can be applied, after agreement between manufacturer and purchaser, to curved sheets.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This Standard gives specifications for asbestos free fibre-cement manholes and inspection chambers for use in buried drains and sewers with gravity flow at atmospheric pressure.  
Products covered by this standard include prefabricated elements in as well as prefabricated complete manholes and inspection chambers.
It specifies definitions, descriptions, composition, general appearance and finish, geometrical characteristics, mechanical characteristics, acceptance tests, type tests and quality control requirements.
NOTE   Complete manholes or prefabricated elements may also be used for other purposes such as pumping stations, items of drainage, items for sewage treatment or sewage disposal, when corresponding additional requirements according to the relevant European Standards are fulfilled.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Migrated from Progress Sheet (TC Comment) (2000-07-10): Under UAP following BT C115/2000

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This draft European Standard, applies to both types of fibre-cement pipes AT and NT as defined in EN 512:1994, gives installation recommendations for this pipelines in above or below ground situations. It complements the general principles for all types of water supply systems specified in EN 805:2000, "Water supply - Requirements for systems and components outside buildings", and should be used in conjunction with that standard. This standard gives guidance in on-site working methods and in the selection and use of approved tools for cutting and machining fibre-cement pipes. This standard does not cover the following : a) installation by thrust boring and pipe jacking methods which require the use of highly specialized techniques ; b) problems caused by the use of special installations procedures (e.g. removal of pile sheeting in very deep trenches, etc.).

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Sstandard applies to fibre-cement pipes, joints and fittings used for sewerage and rainwater discharge systems for buildings where pressure tight joints are required. It defines general composition, classification, geometrical, mechanical and physical characteristics and quality control.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part 1 of EN 588 specifies requirements for fibre-cement pipes, joints and fittings suitable for gravity systems at atmospheric pressure intended for sewerage and drainage applications. It is applicable only to the more commonly used fittings i.e. angled branches or tees and bends. It defines general composition, classification, geometrical, mechanical and physical characteristics, acceptance tests and type tests.

  • Standard
    67 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the characteristics of fibre-cement pipes and joints for use under pressure for conveying potable and non potable water and sewage. It is concerned with composition, classification, geometrical, mechanical and physical characteristics, acceptance tests and type tests.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Establishes rules for batching, sampling, inspection and acceptance/rejection of asbestos-cement products. Provides for a uniform method to be used in determining the accordance of the asbest-cement goods with the relevant requirements for such products and a double sampling plan for the method of inspection by attributes as well as an alternative single sampling plan for the method of inspection by variables.

  • Standard
    18 pages
    English language
    sale 15% off
  • Standard
    18 pages
    French language
    sale 15% off
  • Standard
    18 pages
    French language
    sale 15% off

This European Standard specifies the technical requirements and establishes methods of inspection and test as well as acceptance conditions for fibre-cement flat sheets, siding shingles and planks (referred to as sheets later in this document) for one or more of the following uses:
-   internal wall and ceiling finishes;
-   external wall and ceiling finishes.
Products covered by this European Standard can be used for other purposes provided they comply with the relevant application standard, e.g. rigid underlays.
This European Standard covers sheets reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not cover sheets for fire protection purposes.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.

  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement slates and their fibre-cement fittings for one or more of the following uses:
- roofing
- internal wall finishes
- external and ceiling finishes.
This European Standard applies to fibre-cement slates with a height dimension h (see Clause 4) not exceeding 850 mm for overlapping assembly. For the purpose of this European Standard, fibre-cement slates have been classified according to their bending moment.
This European Standard covers fibre-cement slates reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed products.

  • Amendment
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the technical requirements and establishes methods of inspection and test as well as acceptance conditions for fibre-cement flat sheets, siding shingles and planks (referred to as sheets later in this document) for one or more of the following uses:
- internal wall and ceiling finishes,
- external wall and ceiling finishes.
Products covered by this European Standard can be used for other purposes provided they comply with the relevant application standard, e.g. rigid underlays.
This European Standard covers sheets reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not cover sheets for fire protection purposes.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.

  • Amendment
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement profiled sheets and their fibre-cement fittings for one or more the following uses:
- roofing;
- internal wall finishes;
- external wall and ceiling finishes.
For the purpose of this European Standard, fibre-cement profiles sheets are classified according to their height of corrugation and their mechanical characteristics.
This European Standard covers fibre-cement profiled sheets reinforced with fibres of different type as specified in  5.1.1, with and without facotory applied coating.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.
NOTE: Some of these requirements can be applied, after agreement, to curved sheets for specific applications

  • Amendment
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the technical requirements and establishes methods of inspection and test as well as acceptance conditions for fibre-cement flat sheets, siding shingles and planks (referred to as sheets later in this document) for one or more of the following uses:
- internal wall and ceiling finishes,
- external wall and ceiling finishes.
Products covered by this European Standard can be used for other purposes provided they comply with the relevant application standard, e.g. rigid underlays.
This European Standard covers sheets reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not cover sheets for fire protection purposes.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.

  • Amendment
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the technical requirements and establishes methods of inspection and test as well as acceptance conditions for fibre-cement flat sheets, siding shingles and planks (referred to as sheets later in this document) for one or more of the following uses:
-   internal wall and ceiling finishes;
-   external wall and ceiling finishes.
Products covered by this European Standard can be used for other purposes provided they comply with the relevant application standard, e.g. rigid underlays.
This European Standard covers sheets reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not cover sheets for fire protection purposes.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.

  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement profiled sheets and their fibre-cement fittings for one or more the following uses:
- roofing;
- internal wall finishes;
- external wall and ceiling finishes.
For the purpose of this European Standard, fibre-cement profiles sheets are classified according to their height of corrugation and their mechanical characteristics.
This European Standard covers fibre-cement profiled sheets reinforced with fibres of different type as specified in  5.1.1, with and without facotory applied coating.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.
NOTE: Some of these requirements can be applied, after agreement, to curved sheets for specific applications

  • Amendment
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement slates and their fibre-cement fittings for one or more of the following uses:
- roofing
- internal wall finishes
- external and ceiling finishes.
This European Standard applies to fibre-cement slates with a height dimension h (see Clause 4) not exceeding 850 mm for overlapping assembly. For the purpose of this European Standard, fibre-cement slates have been classified according to their bending moment.
This European Standard covers fibre-cement slates reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed products.

  • Amendment
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the technical requirements and establishes methods of inspection and test as well as acceptance conditions for fibre-cement flat sheets, siding shingles and planks (referred to as sheets later in this document) for one or more of the following uses:
-   internal wall and ceiling finishes;
-   external wall and ceiling finishes.
Products covered by this European Standard can be used for other purposes provided they comply with the relevant application standard, e.g. rigid underlays.
This European Standard covers sheets reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not cover sheets for fire protection purposes.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.

  • Standard
    63 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement slates and their fibre-cement fittings for one or more of the following uses:
-   roofing;
-   internal wall finishes;
-   external wall and ceiling finishes.
This European Standard applies to fibre-cement slates with a height dimension h (see Clause 4) not exceeding 850 mm for overlapping assembly. For the purpose of this European Standard, fibre-cement slates have been classified according to their bending moment.
This European Standard covers fibre-cement slates reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed products.

  • Standard
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the technical requirements and establishes methods of inspection and test as well as acceptance conditions for fibre-cement flat sheets, siding shingles and planks (referred to as sheets later in this document) for one or more of the following uses:
-   internal wall and ceiling finishes;
-   external wall and ceiling finishes.
Products covered by this European Standard can be used for other purposes provided they comply with the relevant application standard, e.g. rigid underlays.
This European Standard covers sheets reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not cover sheets for fire protection purposes.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.

  • Standard
    63 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement slates and their fibre-cement fittings for one or more of the following uses:
-   roofing;
-   internal wall finishes;
-   external wall and ceiling finishes.
This European Standard applies to fibre-cement slates with a height dimension h (see Clause 4) not exceeding 850 mm for overlapping assembly. For the purpose of this European Standard, fibre-cement slates have been classified according to their bending moment.
This European Standard covers fibre-cement slates reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed products.

  • Standard
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement slates and their fibre-cement fittings for one or more of the following uses: - roofing; - internal wall finishes; - external wall and ceiling finishes.

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the technical requirements and establishes methods of inspection and test as well as acceptance conditions for fibre-cement flat sheets, siding shingles and planks for one or more of the following uses: internal wall and ceiling finishes; external wall and ceiling finishes.

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement slates and their fibre-cement fittings for one or more of the following uses:
-   roofing;
-   internal wall finishes;
-   external wall and ceiling finishes.
This European Standard applies to fibre-cement slates with a height dimension h (see Clause 4) not exceeding 850 mm for overlapping assembly. For the purpose of this European Standard, fibre-cement slates have been classified according to their bending moment.
This European Standard covers fibre-cement slates reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed products.

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the technical requirements and establishes methods of inspection and test as well as acceptance conditions for fibre-cement flat sheets, siding shingles and planks (referred to as sheets later in this document) for one or more of the following uses:
-   internal wall and ceiling finishes;
-   external wall and ceiling finishes.
Products covered by this European Standard can be used for other purposes provided they comply with the relevant application standard, e.g. rigid underlays.
This European Standard covers sheets reinforced with fibres of different types as specified in 5.1.1.
This European Standard does not cover sheets for fire protection purposes.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement profiled sheets and their fibre-cement fittings for one or more of the following uses: - roofing; - internal wall finishes; - external wall and ceiling finishes.

  • Standard
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement profiled sheets and their fibre-cement fittings for one or more of the following uses:
-   roofing;
-   internal wall finishes;
-   external wall and ceiling finishes.
For the purpose of this European Standard, fibre-cement profiled sheets are classified according to their height of corrugation and their mechanical characteristics.
This European Standard covers fibre-cement profiled sheets reinforced with fibres of different type as specified in 5.1.1, with and without factory applied coating.
This European Standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.
NOTE   Some of these requirements can be applied, after agreement, to curved sheets for specific applications.

  • Standard
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement profiled sheets and their fibre-cement fittings for one or more of the following uses:
-   roofing,
-   internal wall finishes,
-   external wall and ceiling finishes.
For the purpose of this document fibre-cement profiled sheets are classified according to their height of corrugation and their mechanical characteristics.
This document covers fibre-cement profiled sheets reinforced with fibres of different type as specified in 5.1.1, with and without factory applied coating.
This document does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.
NOTE   Some of these requirements can be applied to curved sheets, after agreement between manufacturer and purchaser.

  • Standard
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement slates and their fibre-cement fittings for one or more of the following uses: - roofing, - internal wall finishes, - external wall and ceiling finishes. It applies to fibre-cement slates with a height dimension h (see Clause 4) not exceeding 850 mm for overlapping assembly. For the purpose of this standard, fibre-cement slates have been classified according to their bending moment. This document covers fibre-cement slates reinforced with fibres of different types as specified in 5.1.1. This standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed products.

  • Amendment
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement slates and their fibre-cement fittings for one or more of the following uses: - roofing, - internal wall finishes, - external wall and ceiling finishes. It applies to fibre-cement slates with a height dimension h (see Clause 4) not exceeding 850 mm for overlapping assembly. For the purpose of this standard, fibre-cement slates have been classified according to their bending moment. This document covers fibre-cement slates reinforced with fibres of different types as specified in 5.1.1. This standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed products.

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement slates and their fibre-cement fittings for one or more of the following uses:
-   roofing,
-   internal wall finishes,
-   external wall and ceiling finishes.
It applies to fibre-cement slates with a height dimension h (see Clause 4) not exceeding 850 mm for overlapping assembly. For the purpose of this standard, fibre-cement slates have been classified according to their bending moment.
This document covers fibre-cement slates reinforced with fibres of different types as specified in 5.1.1.
This standard does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed products.

  • Standard
    48 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the technical requirements and establishes methods of inspection and test as well as acceptance conditions for fibre-cement flat sheets, siding shingles and planks (referred to as sheets later in this document) for one or more of the following uses: - internal wall and ceiling finishes, - external wall and ceiling finishes. Products covered by this document can be used for other purposes provided they comply with the relevant application standard, e.g. rigid underlays. This document covers sheets reinforced with fibres of different types as specified in 5.1.1. This document does not cover sheets for fire protection purposes. This document does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.

  • Amendment
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the technical requirements and establishes methods of inspection and test as well as acceptance conditions for fibre-cement flat sheets, siding shingles and planks (referred to as sheets later in this document) for one or more of the following uses: - internal wall and ceiling finishes, - external wall and ceiling finishes. Products covered by this document can be used for other purposes provided they comply with the relevant application standard, e.g. rigid underlays. This document covers sheets reinforced with fibres of different types as specified in 5.1.1. This document does not cover sheets for fire protection purposes. This document does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.

  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the technical requirements and establishes methods of inspection and test as well as acceptance conditions for fibre-cement flat sheets, siding shingles and planks (referred to as sheets later in this document) for one or more of the following uses:
- internal wall and ceiling finishes,
- external wall and ceiling finishes.
Products covered by this document can be used for other purposes provided they comply with the relevant application standard, e.g. rigid underlays.
NOTE   prEN 14964 "Roof covering products for discontinuous laying and products for wall cladding - Rigid underlays - Rigid underlays for discontinuously laid roof coverings - Product specification and test methods" is under preparation.
This document covers sheets reinforced with fibres of different types as specified in 5.1.1.
This document does not cover sheets for fire protection purposes.
This document does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the technical requirements and establishes methods of control and test as well as acceptance conditions for fibre-cement profiled sheets and their fibre-cement fittings for one or more of the following uses:
-   roofing,
-   internal wall finishes,
-   external wall and ceiling finishes.
For the purpose of this document fibre-cement profiled sheets are classified according to their height of corrugation and their mechanical characteristics.
This document covers fibre-cement profiled sheets reinforced with fibres of different type as specified in 5.1.1, with and without factory applied coating.
This document does not include calculations with regard to works, design requirements, installation techniques, wind uplift or rain proofing of the installed sheets.
NOTE   Some of these requirements can be applied to curved sheets, after agreement between manufacturer and purchaser.

  • Standard
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Introduction in the approved standard of provisions on mounting and fixing for the single burning items test method (EN 13823)

  • Amendment
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day