33.160.99 - Other audio, video and audiovisual equipment
ICS 33.160.99 Details
Other audio, video and audiovisual equipment
Weitere Aspekte der Audio-, Video- und Audiovisuellen Technik
Autres equipements audio et video
Druga avdio, video in avdiovizuelna oprema
General Information
e-Library Subscription
Create subscription and get permanent access to documents within 33.160.99 - Other audio, video and audiovisual equipment
Currently subscription includes documents marked with .We are working on making all documents available within the subscription.
IEC TR 63246-4:2022 describes the CCIS protocol, which includes the protocol messages, parameters and procedures performed by protocol entities. This part is informative; its intent is to provide information that can be considered in order to implement the CCIS protocol.
- Technical report27 pagesEnglish languagesale 15% off
IEC 62394:2022 specifies requirements for service diagnostic software to be implemented in products that incorporate a digital interface. It does not specify requirements for carrying out remote diagnosis or for manufacturer-dependent software.
The Service Diagnostic Interface (SDI) requires an external controller (exclusive or general-purpose/PC) into which service diagnostic software can be loaded. Parts of the controller software are standardized while other parts are proprietary to the manufacturers.
To reach a common approach in servicing all products from all manufacturers, it is necessary to standardize specific items to be tested in products and certain aspects of controllers' diagnostic software.
The SDI is based upon ECHONET specification version 2.11, ECHONET Lite specification version 1.13, and APPENDIX Detailed Requirements for ECHONET Device objects Release M, because this interface will be used in future products. The use of this connection and existing communication protocols enable implementation in products at a low cost, with maximum flexibility and efficiency.
The SDI consists of
• specific hardware and software requirements of the device under test (DUT);
• specific requirements of the controller:
– the service software;
– an ECHONET interface;
• the connection between the controller and the DUT.
This document provides the minimal requirements necessary to carry out computerized diagnosis. It covers the standardized software of the controller as well as the standardized software and provisions in the DUT.
IEC 62394:2022 cancels and replaces the third edition published in 2017. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) updates of the device object super class specifications for the property configurations shared by all device objects;
b) modification and addition of the property configurations defined by each object;
c) addition of new device objects and their property configurations;
d) updates to Bibliography.
- Standard507 pagesEnglish languagesale 15% off
This part of IEC 63033 specifies recording methods of the surround view system that is specified in IEC 63033-1 in order to view the recorded video file with free eye point technology.
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft10 pagesEnglish languagesale 10% offe-Library read for1 day
This part of IEC 63033 specifies the model for generating the surrounding visual image of the surround view system.
- Standard27 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft26 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 63033-2:2022 is available as IEC 63033-2:2022 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 63033-2:2022 specifies recording methods of the surround view system that is specified in IEC 63033-1 in order to view the video file recorded with "free eye point" technology. IEC 63033-2:2022 cancels and replaces the first edition published in 2018. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) updates to the text and the title to reflect the change of the scope of the IEC 63033 series.
- Standard20 pagesEnglish and French languagesale 15% off
IEC 63033-1:2022 specifies the model for generating the surrounding visual image of the surround view system.
IEC 63033-1:2022 cancels and replaces IEC TS 63033-1 published in 2017. This edition constitutes a technical revision.
- Standard49 pagesEnglish and French languagesale 15% off
This part of IEC 63246 specifies the CCIS requirements, which include the general, functional and service requirements for CCIS.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft12 pagesEnglish languagesale 10% offe-Library read for1 day
This part of IEC 63246 describes the CCIS framework, which includes the information flows for registration, device monitoring and control, and content delivery between CCIS functional entities.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft14 pagesEnglish languagesale 10% offe-Library read for1 day
This part of IEC 63087 specifies requirements, and the associated methods of measurement, for the electroacoustic performance of personal listening systems. This document specifies requirements for the provision of assistive listening in audio, video and multimedia systems and equipment. The requirements are of different kinds, because of the diversity of the hardware concerned. Existing IEC standards for methods of measurement are normatively referenced if they exist. Methods of measurement and performance requirements are specified in IEC 63087-21. This document does not apply to hearing aids. Also excluded are devices entirely worn on or in the ear, which cannot be measured independently.
- Standard13 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft10 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 63087-1:2021 specifies requirements, and the associated methods of measurement, for the electroacoustic performance of personal listening systems.
This document specifies requirements for the provision of assistive listening in audio, video and multimedia systems and equipment. The requirements are of different kinds, because of the diversity of the hardware concerned. Existing IEC standards for methods of measurement are normatively referenced if they exist. Methods of measurement and performance requirements are specified in IEC 63087-2.
This document does not apply to hearing aids. Also excluded are devices entirely worn on or in the ear, which cannot be measured independently.
- Standard21 pagesEnglish and French languagesale 15% off
IEC TR 63308:2021 discusses the market of virtual reality (VR) and the technical domains pertaining to a VR system. This document provides clarity on how existing standards can be used and highlights further requirements for standards within the scope of TC 100.
- Technical report20 pagesEnglish languagesale 15% off
IEC 62731:2018(E) specifies the text-to-speech functionality for a (broadcast) receiver with a text-to-speech system. Such a system may be one device, i.e. a receiver with an integrated text-to-speech generator, or may be two devices, i.e. a receiver interfacing with an external text-to-speech device. This document applies only to completely functional stationary (or semi-stationary) digital TV receivers such as set top boxes, integrated digital TVs, recorders and other products whose primary function is to receive TV content. Where this document refers to TV, this will be shorthand for all such receivers. This document does not apply to products that are capable of receiving TV as a secondary function (e.g. PCs or game consoles with digital television receivers). It also does not apply to sub-assemblies (e.g. PC tuner cards). This edition includes the following significant technical changes with respect to the previous edition: a) in 6.2, the levels of announcement quality were revised as well as considerations for ways in which device users can provide service providers with feedback on incorrectly announced terms. b) in 6.3, the following TV functionality was added: the TV can receive updated words, associated conversions and updated conversion rules for the TTS engine via a network connection.
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies a file format for interchanging audio data between compliant
equipment. It is primarily intended for audio applications in professional recording, production,
post-production, and archiving.
It is derived from the AES31-2 [2] but is also compatible with variant specifications including
EBU Tech 3285 [3] to [10], ITU-R BR.1352-3-2007 [11] to [14], and the Japan Post Production
Association's BWF-J [15].
This document contains the specification of the broadcast audio extension chunk and its use
with PCM-coded audio data. Basic information on the RIFF format and how it can be extended
to other types of audio data is given in Annex E. Details of the PCM WAVE format are also
given in Annex A.
An optional extended format, BWF-E, supports 64-bit addressing to permit file sizes greater
than 4 GB.
- Standard44 pagesEnglish languagesale 10% offe-Library read for1 day
- Draft39 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 63029:2017 specifies the scanning scheme to develop raster-graphics image-based e-books from existing printed books.
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 63028:2017(E) defines technical requirements, behaviors and interfaces used for ensuring interoperability for flexibly coupled wireless power transfer (WPT) systems for AirFuel Resonant WPT. This document is based on AirFuel Wireless Power Transfer System Baseline System Specification (BSS) v1.3.
- Standard98 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62827-2:2017(E), IEC 62827 defines a wireless power management protocol for wireless power transfer to multiple devices in a wireless power management system. Various functions of wireless power management systems are justified. The wireless power management frames and messages that work between the management block of a power source and the management block or the coupler block of a device, or the coupler block of a power source, are defined as well to execute various functions. Also, the procedures for each functionality are described based on its frames and messages.
- Standard54 pagesEnglish languagesale 10% offe-Library read for1 day
IEC TR 63231:2019 describes the technical background of current energy efficiency efforts related to wireless power transfer (WPT) technology and commercially available products related to related to audio, video and multimedia systems and equipment. This Technical Report examines use cases, standardization efforts of other standards development organizations (SDOs) and known national regulations. This document concludes with observations and recommendations for the potential future technical standards development activities within the scope of TC 100.
- Technical report14 pagesEnglish languagesale 15% off
IEC 62665:2015(E) this International Standard specifies: - a text encoding scheme to generate a texture map, - a physical shape and dimension of the texture map for printing, - additional features for texture map printing and - a texture map decoding and an auditory presentation of decoded texts. These specifications enable the interchange of documents and publications between visually impaired and non-impaired people. This second edition cancels and replaces the first edition published in 2012 and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition. Two different control codes are described by the different terms: "control codes for text" and "control codes for speech". Pack processing and LZSS processing are shown in their additional subclauses. An example of the header file "Speechio.h" is added. An example of error correction encoding is shown in additional Annex D.
- Standard44 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 63033-2:2018 specifies recording methods of the drive monitoring system that is specified in IEC TS 63033-1 in order to view the recorded video file with free eye point technology.
- Standard20 pagesEnglish and French languagesale 15% off
ISO 20108:2017 sets out requirements for the quality and transmission of sound and image input to interpreters and specifies the characteristics of the audio and video signals. The components of typical interpreting systems are specified in ISO 20109. Together with either permanent (see ISO 2603) or mobile (see ISO 4043) booths, these interpreting systems form the interpreters' working environment. In addition to setting out the requirements for on-site interpreting, where participants (speakers and members of the audience) and interpreters are at the same location, ISO 20108:2017 specifies requirements for different varieties of distance interpreting situations in which the interpreters are not at the same location as one or more of the conference participants.
ISO 20108:2017 also addresses the work of manufacturers and providers of simultaneous interpreting equipment and technical staff.
In conjunction with either ISO 2603 or ISO 4043, ISO 20108:2017 and ISO 20109 provide the relevant requirements both for the quality and transmission of sound and image provided to interpreters and for the equipment needed in the booths, the conference room and the distant site(s).
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
This document defines technical requirements, behaviors and interfaces used for ensuring
interoperability for flexibly coupled wireless power transfer (WPT) systems for AirFuel
Resonant WPT. This document is based on AirFuel Wireless Power Transfer System Baseline
System Specification (BSS) v1.3.
Products implementing this document are expected to follow applicable regulations and global
standards.
- Standard98 pagesEnglish languagesale 10% offe-Library read for1 day
This document sets out requirements for the quality and transmission of sound and image input to
interpreters and specifies the characteristics of the audio and video signals. The components of typical
interpreting systems are specified in ISO 20109. Together with either permanent (see ISO 2603) or
mobile (see ISO 4043) booths, these interpreting systems form the interpreters’ working environment.
In addition to setting out the requirements for on-site interpreting, where participants (speakers
and members of the audience) and interpreters are at the same location, this document specifies
requirements for different varieties of distance interpreting situations in which the interpreters are
not at the same location as one or more of the conference participants.
This document also addresses the work of manufacturers and providers of simultaneous interpreting
equipment and technical staff.
In conjunction with either ISO 2603 or ISO 4043, this document and ISO 20109 provide the relevant
requirements both for the quality and transmission of sound and image provided to interpreters and
for the equipment needed in the booths, the conference room and the distant site(s).
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
IEC corrigendum
- Corrigendum3 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 60728-2:2018(E) applies to the radiation characteristics and immunity to electromagnetic disturbance of EM active equipment (active and passive equipment) for the reception, processing and distribution of television, sound and interactive multimedia signals as dealt with in IEC 60728-3, IEC 60728-4, IEC 60728-5 and IEC 60728-6.
This document covers the following frequency ranges:
- disturbance voltage injected into the mains: 150 kHz to 30 MHz;
- radiation from active equipment: 5 MHz to 25 GHz;
- immunity of active equipment: 150 kHz to 25 GHz;
- screening effectiveness of passive equipment: 5 MHz to 3,5 GHz.
This document specifies requirements for maximum allowed radiation, minimum immunity and minimum screening effectiveness and describes test methods for conformance testing.
This third edition cancels and replaces the second edition published in 2010. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) Frequency extensions:
a.1) The upper frequency limit of conventional cable network equipment was extended from 862 MHz to 1 000 MHz due to market demands.
a.2) The first intermediate frequency range (1st IF range) for satellite signal transmission was extended to cover now frequencies from 950 MHz up to 3 500 MHz.
a.3) The methods of measurement and the EMC requirements in the overlapping frequency range from 950 MHz to 1 000 MHz were allocated in relation to the upper frequency limit, 1 000 MHz, and the lower frequency limit, 950 MHz, of the relevant equipment under test.
b) New EMC environment in the 800 MHz band:
b.1) The European Commission has requested CENELEC and ETSI to draft immunity requirements for equipment, to protect against disturbance from the new wireless service in the 790 MHz to 862 MHz band.
b.2) A CENELEC/ETSI Joint Working Group “Digital Dividend” was formed to describe the new EMC environment and to advise on appropriate test methods and limits.
b.3) IEC 60728-2 is the document specifying immunity requirements for active and passive cable network equipment.
b.4) The method of measurement and the requirements for in-band immunity were extended taking into account this new EMC environment due to the allocation of broadband wireless services in the frequency band 694 MHz to 862 MHz. As a consequence, the limits of in-band immunity were specified for analogue and additionally for digital signals in this frequency range.
b.5) Consequently it is recommended, that, where cable networks and wireless networks coexist, only the transmission of digitally modulated signals should be used in the frequency range 694 MHz to 862 MHz.
b.6) For passive equipment, Class A and Class B specifications were kept in the standard but a note was added recommending that only Class A equipment should be used in the planning and implementation of new networks.
c) The methods of measurement for all kinds of indoor antennas were combined in the new 4.9.
d) A Bibliography has been added at the end of the document referencing, for example, CEPT Report 30 on “The identification of common and minimal (least restrictive) technical conditions for 790-862 MHz for the digital dividend in the European Union”.
- Standard56 pagesEnglish languagesale 15% off
IEC 62731:2018 specifies the text-to-speech functionality for a (broadcast) receiver with a text-to-speech system. Such a system may be one device, i.e. a receiver with an integrated text-to-speech generator, or may be two devices, i.e. a receiver interfacing with an external text-to-speech device. This document applies only to completely functional stationary (or semi-stationary) digital TV receivers such as set top boxes, integrated digital TVs, recorders and other products whose primary function is to receive TV content. Where this document refers to TV, this will be shorthand for all such receivers.
This document does not apply to products that are capable of receiving TV as a secondary function (e.g. PCs or game consoles with digital television receivers). It also does not apply to sub-assemblies (e.g. PC tuner cards).
This edition includes the following significant technical changes with respect to the previous edition:
a) in 6.2, the levels of announcement quality were revised as well as considerations for ways in which device users can provide service providers with feedback on incorrectly announced terms.
b) in 6.3, the following TV functionality was added: the TV can receive updated words, associated conversions and updated conversion rules for the TTS engine via a network connection.
- Standard19 pagesEnglish languagesale 15% off
- Standard39 pagesEnglish and French languagesale 15% off
IEC 63029:2017 specifies the scanning scheme to develop raster-graphics image-based e-books from existing printed books.
The contents of the corrigendum of January 2018 have been included in this copy.
- Standard18 pagesEnglish languagesale 15% off
- Standard38 pagesEnglish and French languagesale 15% off
IEC 62827-2:2017, defines a wireless power management protocol for wireless power transfer to multiple devices in a wireless power management system. Various functions of wireless power management systems are justified. The wireless power management frames and messages that work between the management block of a power source and the management block or the coupler block of a device, or the coupler block of a power source, are defined as well to execute various functions. Also, the procedures for each functionality are described based on its frames and messages.
- Standard51 pagesEnglish languagesale 15% off
- Standard109 pagesEnglish and French languagesale 15% off
IEC 63028:2017 defines technical requirements, behaviors and interfaces used for ensuring interoperability for flexibly coupled wireless power transfer (WPT) systems for AirFuel Resonant WPT. This document is based on AirFuel Wireless Power Transfer System Baseline System Specification (BSS) v1.3.
- Standard95 pagesEnglish languagesale 15% off
- Standard203 pagesEnglish and French languagesale 15% off
IEC 62766-1:2017(E) defines general common elements and specifies the structure of the IEC 62766 series, the scopes of, and relationships between the other parts
- Standard44 pagesEnglish languagesale 15% off
IEC 62394:2017 specifies requirements for service diagnostic software to be implemented in products that incorporate a digital interface. The Service Diagnostic Interface (SDI) requires an external controller (exclusive or general-purpose/PC) into which service diagnostic software can be loaded. Parts of the controller software should be standardized while other parts should be unique to the manufacturer. The SDI is based upon ECHONET specification version 2.11, ECHONET Lite specification version 1.11, and APPENDIX Detailed Requirements for ECHONET Device objects Release G, because this interface will be used in future products. The use of this connection and existing communication protocols enable implementation in products at a low cost, with maximum flexibility and efficiency.
- Standard358 pagesEnglish languagesale 15% off
This part of IEC 62580 specifies the general architecture of the On-board Multimedia and
Telematic Subsystem, which includes four categories of multimedia and telematic subsystems
identified as:
A Video surveillance/CCTV
B Driver and crew orientated services
C Passenger orientated services
D Train operator and maintainer orientated services
This part establishes:
• the boundary between the OMTS and the on-board communication system, as described
by the IEC 61375 series
• the methodology to describe an OMTS in terms of abstract model
• the general principles and the basic requirements to specify the services provided/needed
by each category
• the approach to ensure interoperability between services
This part gives guidelines for:
• OMTS classification
• functional breakdown structuring
• system breakdown structuring
• formal specification of an OMTS
This part is applicable to any type of train, e.g. open trains, multiple unit trains and closed
trains.
NOTE The general architecture provides a common basis for the application categories defined in part 2 and
possible future parts of this series of standards. Consequently, the approach is homogeneous for all multimedia
and telematic subsystems addressed by this series of standards.
- Standard77 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 60728-6:2011(E) lays down the measuring methods, performance requirements and data publication requirements of optical equipment of cable networks for television signals, sound signals and interactive services. This third edition cancels and replaces the second edition published in 2003 of which it constitutes a technical revision. It includes the following significant technical changes with respect to the previous edition: - The normative references were updated. - The methods of measurement for optical power and return loss were substituted by references to other standards. - The method of measurement for polarization dependent loss was deleted. - A method of measurement for carrier-to-crosstalk ratio (CCR) was added. - The methods of measurement for CSO and CTB of optical amplifiers were substituted by a method of measurement for microscopic gain tilt of optical amplifiers. This parameter can be used for calculating the second order distortion of optical amplifiers according to the method described in the new Annex B. New classes for optical transmitters and receivers have been defined.
- Standard67 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62637-1:2011 defines a charging interface between small handheld multimedia devices and power-supply accessories, specifically chargers. Devices, which could be based on this standard may vary over time, but have to comply with the limited power available. The interface is a 2 mm barrel type charging interface. The French version of this standard has not been voted upon. This bilingual version (2011-07) replaces the English version.
- Standard24 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62637-2:2011 provides the conformance testing rules and guidelines for equipment built to meet the 2 mm barrel type charging interface specified in the 62637-1. This bilingual version (2011-07) replaces the English version.
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
This part of IEC 62629 provides a list of the terminologies that are frequently used in describing 3D display technologies in the IEC 62629 series. Terms for various 3D display technologies on stereoscopic, autostereoscopic, volumetric, and holographic displays are included.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 60728-1-2:2014 provides the minimum performance requirements to be fulfilled in operation at the system outlet or terminal input and describes the summation criteria for the impairments present in the received signals and those produced by the CATV/MATV/SMATV cable network, including individual receiving systems. It is applicable to cable networks intended for television signals, sound signals and interactive services operating between about 5 MHz and 3 000 MHz. The frequency range is extended to 6 000 MHz for home distribution techniques that replace wired cords with a wireless two way communication inside a room (or a small number of adjacent rooms) that uses the 5 GHz to 6 GHz frequency band. This second edition cancels and replaces the first edition published in 2009, and constitutes a technical revision. It includes the following technical: update of performance requirements in Clause 7 to include those for DVB-T2 signals.
This publication is to be read in conjunction with IEC 60728-1:2007.
- Standard75 pagesEnglish and French languagesale 15% off
IEC 60728-14:2014 describes the system and equipment specification of FTTH/FTTB (fibre to the home/fibre to the building) networks where information is transmitted in both, forward and return path directions using RF subcarrier multiplexing technology, and where the return path transmission uses additionally time division multiple access technique imposed by the transmission of the return path signals using a TDMA (e.g. TDMA mode of DOCSIS) protocol. Such systems are called RF over Glass (RFoG) and consist of an RFoG optical network unit (R-ONU), an optical distribution network based on xPON structure, and an RFoG optical return path receiver. This standard specifies the basic system parameters and methods of measurement for RFoG systems in order to assess the system performance and its performance limits.
- Standard112 pagesEnglish and French languagesale 15% off
IEC 62524:2009 specifies a reader's format for multimedia e-publishing employed for e-book data interchange among publishers and readers, satisfying a number of readers' requirements such as being non-revisable, equipment-adaptive and application-adaptive.
- Standard51 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62394:2013 specifies requirements for service diagnostic software to be implemented in products that incorporate a digital interface. It does not specify requirements for carrying out remote diagnosis or for manufacturer-dependent software. It is based upon the ECHONET specification version 2.11, ECHONET Lite specification version 1.01 and APPENDIX Detailed Requirements for ECHONET Device objects Release B because this interface will be used in future products. The use of this connection and existing communication protocols enable implementation in products at low cost, with maximum flexibility and efficiency. This second edition cancels and replaces the first edition, published in 2006, and constitutes a technical revision. It includes the following changes:
- addition of new message structure (frame format);
- updates of the device object super class specifications for the property configurations shared by all device objects;
- addition of the property configurations defined by each device object;
- updates of normative references.
- Standard511 pagesEnglish and French languagesale 15% off
This part of IEC 62629-22 specifies optical measuring methods for autostereoscopic display devices. It defines general measuring procedures for optical characteristics of two-view and multi-view displays and integral imaging displays.
- Standard36 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 62731:2013 specifies the text-to-speech functionality for a (broadcast) receiver with a text-to-speech system. Such a system may be one device, i.e. a receiver with an integrated text-to-speech generator, or may be two devices, i.e. a receiver interfacing with an external text-to-speech device. This International Standard applies only to completely functional stationary (or semi-stationary) digital TV receivers such as set top boxes, integrated digital TVs, recorders and other products whose primary function is to receive TV content.
- Standard38 pagesEnglish and French languagesale 15% off
IEC/TR 62780:2012(E) provides protection schemes against mechanical stress during distribution or keeping of e-books (see IEC 62229) stored in interchangeable optical storage media such as CDs and DVDs, and shows the stress-strain characteristics of the interchangeable storage media from which the protection schemes are derived.
- Technical report13 pagesEnglish languagesale 15% off
IEC 62665:2012 specifies:
- a text encoding scheme to generate a texture map;
- a physical shape and dimension of the texture map for printing;
- additional features for texture map printing;
- texture map decoding and an auditory presentation of decoded texts. It enables the interchange of documents and publications between visually impaired and non-impaired people.
- Standard48 pagesEnglish and French languagesale 15% off
This part of the IEC 62637 provides the conformance testing rules and guidelines for equipment built to meet the 2 mm barrel type charging interface specified in the 62637-1.
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
This part of IEC 62637 defines a charging interface between small handheld multimedia devices and power-supply accessories, specifically chargers. Devices, which could be based on this standard may vary over time, but have to comply with the limited power available1. The interface is a 2 mm barrel type charging interface. This standard does not include the whole charger nor does it include the internal functions of the device. Chargers and devices shall follow the applicable EMC and safety standards.
- Standard24 pagesEnglish languagesale 10% offe-Library read for1 day
IEC 60728-6:2011 lays down the measuring methods, performance requirements and data publication requirements of optical equipment of cable networks for television signals, sound signals and interactive services. This third edition cancels and replaces the second edition published in 2003 of which it constitutes a technical revision. It includes the following significant technical changes with respect to the previous edition:
- The normative references were updated.
- The methods of measurement for optical power and return loss were substituted by references to other standards.
- The method of measurement for polarization dependent loss was deleted.
- A method of measurement for carrier-to-crosstalk ratio (CCR) was added.
- The methods of measurement for CSO and CTB of optical amplifiers were substituted by a method of measurement for microscopic gain tilt of optical amplifiers.
This parameter can be used for calculating the second order distortion of optical amplifiers according to the method described in the new Annex B. New classes for optical transmitters and receivers have been defined.
- Standard61 pagesEnglish languagesale 15% off
- Standard126 pagesEnglish and French languagesale 15% off
IEC 62637-2:2011 provides the conformance testing rules and guidelines for equipment built to meet the 2 mm barrel type charging interface specified in the 62637-1. This bilingual version (2011-07) replaces the English version.
- Standard36 pagesEnglish and French languagesale 15% off
IEC 62637-1:2011 defines a charging interface between small handheld multimedia devices and power-supply accessories, specifically chargers. Devices, which could be based on this standard may vary over time, but have to comply with the limited power available. The interface is a 2 mm barrel type charging interface. The French version of this standard has not been voted upon. This bilingual version (2011-07) replaces the English version.
- Standard42 pagesEnglish and French languagesale 15% off
IEC 60728-2:2010(E) applies to the radiation characteristics and immunity to electromagnetic disturbance of EM active equipment (active and passive equipment) for the reception, processing and distribution of television, sound and interactive multimedia signals as dealt with in the IEC 60728 series. It specifies requirements for maximum allowed radiation, minimum immunity and minimum screening effectiveness and describes test methods for conformance testing. It cancels and replaces the first edition published in 2002, of which it constitutes a technical revision and includes the following significant technical changes with respect to the previous edition:
- updated scope, added some new terms and definitions;
- added methods of measurement and performance requirements for telecom signal ports of multimedia network equipment;
- updated methods of measurement for immunity and emissions;
- applicability of EMC performance requirements and methods of measurement to different types of equipment.
- Standard53 pagesEnglish languagesale 15% off
IEC 60728-1-2:2009 provides the minimum performance requirements to be fulfilled in operation at the system outlet or terminal input and describes the summation criteria for the impairments present in the received signals and those produced by the CATV/MATV/SMATV cable network, including individual receiving systems. This bilingual version, published in 2011-03, corresponds to the English version. The French version of this standard has not been voted upon.
- Standard33 pagesEnglish languagesale 15% off
- Standard68 pagesEnglish and French languagesale 15% off