SIST EN ISO 583:2008

SLOVENSKI oSIST prEN ISO 583:2005

PREDSTANDARD
maj 2005
Naprave za kontinuirni transport - Trakovi tračnih transporterjev s tekstilnim
vložkom - Tolerance celotne debeline in debeline oblog - Neposredna merilna
metoda (ISO/DIS 583:2005)
Conveyor belts with a textile carcass - Tolerances on total thickness and thickness
of covers - Direct measurement method (ISO/DIS 583:2005)
ICS 53.040.20 Referenčna številka
oSIST prEN ISO 583:2005(en)
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
DRAFT
prEN ISO 583
NORME EUROPÉENNE

EUROPÄISCHE NORM

February 2005
ICS Will supersede EN ISO 583-1:1999
English version
Conveyor belts with a textile carcass - Tolerances on total
thickness and thickness of covers - Direct measurement method
(ISO/DIS 583:2005)
Courroies transporteuses à carcasse textile - Epaisseur
totale de la courroie et épaisseur des éléments - Méthodes
d'essai (ISO/DIS 583:2005)
This draft European Standard is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee
CEN/TC 188.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN ISO 583:2005: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------
prEN ISO 583:2005 (E)




Foreword

This document (prEN ISO 583:2005) has been prepared by Technical Committee ISO/TC 41
"Pulleys and belts (including veebelts)" in collaboration with Technical Committee CEN/TC
188 "Conveyor belts", the secretariat of which is held by BSI.

This document is currently submitted to the parallel Enquiry.

This document will supersede EN ISO 583-1:1999.


Endorsement notice

The text of ISO 583:2005 has been approved by CEN as prEN ISO 583:2005 without any
modifications.

2

---------------------- Page: 3 ----------------------
DRAFT INTERNATIONAL STANDARD ISO/DIS 583
ISO/TC 41/SC 3 Secretariat: BSI
Voting begins on: Voting terminates on:
2005-02-03 2005-07-03
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Conveyor belts with a textile carcass — Total belt thickness and
thickness of elements — Test methods
Courroies transporteuses à carcasse textile — Épaisseur totale de la courroie et épaisseur des éléments —
Méthodes d'essai
[Revision of second edition (ISO 583:1990) and ISO 583-1:1999]
ICS 53.040.20

ISO/CEN PARALLEL ENQUIRY
The CEN Secretary-General has advised the ISO Secretary-General that this ISO/DIS covers a subject
of interest to European standardization. In accordance with the ISO-lead mode of collaboration as
defined in the Vienna Agreement, consultation on this ISO/DIS has the same effect for CEN
members as would a CEN enquiry on a draft European Standard. Should this draft be accepted, a
final draft, established on the basis of comments received, will be submitted to a parallel two-month FDIS
vote in ISO and formal vote in CEN.
To expedite distribution, this document is circulated as received from the committee secretariat.
ISO Central Secretariat work of editing and text composition will be undertaken at publication
stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
© International Organization for Standardization, 2005

---------------------- Page: 4 ----------------------
ISO/DIS 583
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user's country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying,
recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
©
ii ISO 2005 – All rights reserved

---------------------- Page: 5 ----------------------
ISO/DIS 583
Contents Page
Foreword. v
1 Scope. 1
2 Normative references. 1
3 Determination of total belt thickness. 1
3.1 Apparatus. 1
3.2 Test piece. 1
3.3 Measurement points. 2
3.4 Procedure. 4
3.5 Expression of results . 4
4 Determination of thickness of covers. 4
4.1 Method for use when covers can be removed completely from the carcass . 4
4.2 Method for use when covers cannot be removed completely from the carcass. 5
5 Determination of thickness of carcass .6
6 Determination of thickness of interlayer .7
6.1 Method for use when the elastomeric material in the interlayer can be removed
completely from the adjacent fabric ply .7
6.2 Method for use when the elastomeric material in the interlayer cannot be

separated completely from the adjacent fabric ply. 8
7 Test report. 9

© ISO 2005 – All rights reserved iii

---------------------- Page: 6 ----------------------
ISO/DIS 583
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national
standards bodies (ISO member bodies). The work of preparing International Standards is normally
carried out through ISO technical committees. Each member body interested in a subject for which a
technical committee has been established has the right to be represented on that committee.
International organizations, governmental and non-governmental, in liaison with ISO, also take part in
the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all
matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives,
Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 583 was prepared by Technical Committee ISO/TC 41, Pulleys and belts (including veebelts),
Subcommittee SC 3, Conveyor belts.
This third edition of ISO 583 cancels and replaces ISO 583:1990 and ISO 583-1:1999 of which it
constitutes a technical revision.

iv © ISO 2005 – All rights reserved

---------------------- Page: 7 ----------------------
DRAFT INTERNATIONAL STANDARD ISO/DIS 583

Conveyor belts with a textile carcass — Total belt thickness
and thickness of elements — Test methods
1 Scope
This International Standard specifies methods of test for the total thickness and the thickness of
covers of conveyor belts having a textile carcass. It also specifies methods for the determination of
carcass thickness and interlayer thickness.
This International Standard is not suitable or valid for light conveyor belts as described in ISO 21183-
[1]
...