DC or AC supplied electronic step-down convertors for filament lamps - Performance requirements

This International Standard specifies performance requirements for electronic step-down convertors for use on d.c. supplies up to 250 V and a.c. supplies up to 1 000 V at 50 Hz or 60 Hz with operating frequencies deviating from the supply frequency, associated with tungsten halogen lamps as specified in EN 60357 and other filament lamps.

Gleich- oder wechselstromversorgte elektronische Konverter für Glühlampen - Anforderungen an die Arbeitsweise

Convertisseurs abaisseurs électroniques alimentés en courant continu ou alternatif pour lampes à incandescence - Exigences de performance

Cette Norme internationale spécifie les prescriptions de performances pour les convertisseurs abaisseurs électroniques pour les alimentations en courant continu jusqu'à 250 V et les alimentations en courant alternatif jusqu'à 1000 V, à 50 Hz ou 60 Hz fonctionnant à des fréquences différentes de la tension d'alimentation, associés à des lampes à incandescence aux halogènes comme spécifié dans la EN 60357 et à d'autres lampes à incandescence.

Enosmerno ali izmenično napajani elektronski pretvorniki za žarnice in sijalke – Zahteve za tehnične karakteristike (IEC 61047:2004)

General Information

Status
Published
Publication Date
31-May-2005
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Jun-2005
Due Date
01-Jun-2005
Completion Date
01-Jun-2005

Relations

Buy Standard

Standard
EN 61047:2005
English language
20 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI SIST EN 61047:2005

STANDARD
junij 2005
Enosmerno ali izmenično napajani elektronski pretvorniki za žarnice in sijalke
– Zahteve za tehnične karakteristike (IEC 61047:2004)
DC or AC supplied electronic step-down convertors for filament lamps -
Performance requirements (IEC 61047:2004)
ICS 29.140.20 Referenčna številka
SIST EN 61047:2005(en)
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD EN 61047
NORME EUROPÉENNE
EUROPÄISCHE NORM October 2004

ICS 29.140.20 Supersedes EN 61047:1992 + A1:1996 + A2:2001


English version


DC or AC supplied electronic step-down convertors for filament lamps -
Performance requirements
(IEC 61047:2004)


Convertisseurs abaisseurs électroniques Gleich- oder wechselstromversorgte
alimentés en courant continu ou alternatif elektronische Konverter für Glühlampen -
pour lampes à incandescence – Anforderungen an die Arbeitsweise
Exigences de performance (IEC 61047:2004)
(CEI 61047:2004)






This European Standard was approved by CENELEC on 2004-09-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2004 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 61047:2004 E

---------------------- Page: 2 ----------------------

EN 61047:2004 - 2 -
Foreword
The text of document 34C/635/FDIS, future edition 2 of IEC 61047, prepared by SC 34C, Auxiliaries
for lamps, of IEC TC 34, Lamps and related equipment, was submitted to the IEC-CENELEC parallel
vote and was approved by CENELEC as EN 61047 on 2004-09-01.
This European Standard supersedes EN 61047:1992 + A1:1996 + A2:2001.
It constitutes a technical revision. EN 61047:1992 needed to be revised completely after the decision
to delete all EMC-related requirements, given that EMC varies from region to region.
This European Standard is to be read in conjunction with EN 61347-1 and EN 61347-2-2.
In this standard, the following print types are used:
– requirements proper: in roman type;
– test specifications: in italic type;
– notes: in smaller roman type.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2005-06-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2011-09-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61047:2004 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 3 ----------------------

- 3 - EN 61047:2004
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
1) 2)
IEC 60357 (mod) - Tungsten halogen lamps (non-vehicle) - EN 60357 2003
Performance specifications

1)
2)
IEC 61347-1 - Lamp controlgear EN 61347-1 2001
Part 1: General and safety requirements

1)
2)
IEC 61347-2-2 - Part 2-2: Particular requirements for d.c. EN 61347-2-2 2001
or a.c. supplied electronic step-down
convertors for filament lamps





1)
Undated reference.
2)
Valid edition at date of issue.

---------------------- Page: 4 ----------------------

NORME CEI
INTERNATIONALE
IEC



61047
INTERNATIONAL


Deuxième édition
STANDARD

Second edition

2004-06


Convertisseurs abaisseurs électroniques
alimentés en courant continu ou alternatif
pour lampes à incandescence –
Exigences de performances

DC or AC supplied electronic step-down
convertors for filament lamps –
Performance requirements

 IEC 2004 Droits de reproduction réservés  Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
CODE PRIX
Q
PRICE CODE
Commission Electrotechnique Internationale
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
Pour prix, voir catalogue en vigueur
For price, see current catalogue

---------------------- Page: 5 ----------------------

61047  IEC:2004 – 3 –
CONTENTS
FOREWORD.5
INTRODUCTION.9

1 Scope.11
2 Normative references.11
3 Terms and definitions .11
4 General notes on tests .13
5 Classification.15
5.1 Classification according to the load .15
5.2 Classification according to output voltage.15
6 Marking.15
6.1 Mandatory marking.15
6.2 Optional marking.15
7 Output voltage and current .17
7.1 Open-circuit voltage.17
7.2 Voltage during operation.17
7.3 Voltage surges during switching and operation.17
7.4 Voltage waveform.17
7.5 Inrush current.17
8 Total circuit power.19
9 Circuit power factor.19
10 Supply current.19
11 Impedance at audio-frequencies.19
12 Operational tests for abnormal conditions.19
13 Endurance.21

Annex A (normative) Tests.23
Annex B (informative) A guide to quoting product life and failure rate .31

Bibliography.32

Figure A.1 – Measurement of currents .27
Figure A.2 – Measurement of impedance at audio-frequencies .29

---------------------- Page: 6 ----------------------

61047  IEC:2004 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

DC OR AC SUPPLIED ELECTRONIC
STEP-DOWN CONVERTORS FOR FILAMENT LAMPS –
PERFORMANCE REQUIREMENTS


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61047 has been prepared by subcommittee 34C: Auxiliaries for
lamps, of IEC technical committee 34: Lamps and related equipment.
This second edition of IEC 61047 cancels and replaces the first edition published in 1991, its
Amendment 1 (1996) and Amendment 2 (2001). This second edition constitutes a technical
revision. The first edition needed to be revised completely after the decision to delete all
EMC-related requirements, given that EMC varies from region to region.

---------------------- Page: 7 ----------------------

61047  IEC:2004 – 7 –
The text of this standard is based on the following documents:
FDIS Report on voting
34C/635/FDIS 34C/643/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This standard is to be read in conjunction with IEC 61347-1 and IEC 61347-2-2.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
In this standard, the following print types are used:
– requirements proper: in roman type;
– test specifications: in italic type;
– notes: in smaller roman type.

The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.

---------------------- Page: 8 ----------------------

61047  IEC:2004 – 9 –
INTRODUCTION
This International Standard covers performance requirements for electronic step-down
convertors for d.c. supplies up to 250 V and a.c. supplies up to 1 000 V at 50 Hz or 60 Hz,
operating with controlled voltage filament lamps at frequencies deviating from the supply
frequency.
Attention is drawn to the fact that operating frequencies below 20 kHz may cause audio noise.
NOTE CISPR requirements regarding radio interference have to be observed in some countries.
In order to obtain satisfactory performance of filament lamps and electronic convertors, it is
necessary that certain features of their designs be properly coordinated.

---------------------- Page: 9 ----------------------

61047  IEC:2004 – 11 –
DC OR AC SUPPLIED ELECTRONIC
STEP-DOWN CONVERTORS FOR FILAMENT LAMPS –
PERFORMANCE REQUIREMENTS



1 Scope
This International Standard specifies performance requirements for electronic step-down
convertors for use on d.c. supplies up to 250 V and a.c. supplies up to 1 000 V at 50 Hz or
60 Hz with operating frequencies deviating from the supply frequency, associated with
tungsten halogen lamps as specified in IEC 60357 and other filament lamps.
NOTE 1 The tests in this standard are type tests. Requirements for testing individual convertors during production
are not included.
NOTE 2 Requirements for convertors which incorporate means for varying the lamp power are under
consideration.
NOTE 3 It may be expected that convertors complying with this standard will ensure satisfactory operation
between 92 % and 106 % of rated supply voltage of filament lamps with rated lives greater than 200 h and rated
voltage less than 50 V.
NOTE 4 There exist regional standards regarding the regulation of mains current harmonics for end-products
such as luminaires and independent control gear. In a luminaire, the control gear is dominant in this respect.
Control gear, together with other components, should comply with these st
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.