SIST EN ISO 8130-14:2004

SLOVENSKI STANDARD
SIST EN ISO 8130-14:2004
01-julij-2004
Coating powders - Part 14: Terminology (ISO 8130-14:2004)
Coating powders - Part 14: Terminology (ISO 8130-14:2004)
Pulverlacke - Teil 14: Terminologie (ISO 8130-14:2004)
Poudres pour revetement - Partie 14: Terminologie (ISO 8130-14:2004)
Ta slovenski standard je istoveten z: EN ISO 8130-14:2004
ICS:
01.040.87 Industrija barv (Slovarji) Paint and colour industries
(Vocabularies)
87.040 Barve in laki Paints and varnishes
SIST EN ISO 8130-14:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 8130-14:2004

---------------------- Page: 2 ----------------------

SIST EN ISO 8130-14:2004
EUROPEAN STANDARD
EN ISO 8130-14
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2004
ICS 87.040; 01.040.87
English version
Coating powders - Part 14: Terminology (ISO 8130-14:2004)
Poudres pour revêtement - Partie 14: Terminologie (ISO Pulverlacke - Teil 14: Terminologie (ISO 8130-14:2004)
8130-14:2004)
This European Standard was approved by CEN on 6 May 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8130-14:2004: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 8130-14:2004

EN ISO 8130-14:2004 (E)





Foreword


This document (EN ISO 8130-14:2004) has been prepared by Technical Committee ISO/TC 35
"Paints and varnishes" in collaboration with Technical Committee CEN/TC 139 "Paints and
varnishes", the secretariat of which is held by DIN.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by November 2004, and conflicting national
standards shall be withdrawn at the latest by November 2004.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.


Endorsement notice

The text of ISO 8130-14:2004 has been approved by CEN as EN ISO 8130-14:2004 without any
modifications.

2

---------------------- Page: 4 ----------------------

SIST EN ISO 8130-14:2004


INTERNATIONAL ISO
STANDARD 8130-14
First edition
2004-05-15


Coating powders —
Part 14:
Terminology
Poudres pour revêtement —
Partie 14: Terminologie



Reference number
ISO 8130-14:2004(E)
©
ISO 2004

---------------------- Page: 5 ----------------------

SIST EN ISO 8130-14:2004
ISO 8130-14:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2004
The reproduction of the terms and definitions contained in this International Standard is permitted in teaching manuals, instruction
booklets, technical publications and journals for strictly educational or implementation purposes. The conditions for such reproduction are:
that no modifications are made to the terms and definitions; that such reproduction is not permitted for dictionaries or similar publications
offered for sale; and that this International Standard is referenced as the source document.
With the sole exceptions noted above, no other part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2004 – All rights reserved

---------------------- Page: 6 ----------------------

SIST EN ISO 8130-14:2004
ISO 8130-14:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 8130-14 was prepared by Technical Com
...