SIST EN ISO 20349-2:2017

SLOVENSKI STANDARD
SIST EN ISO 20349-2:2017
01-november-2017
1DGRPHãþD
SIST EN ISO 20349:2011
2VHEQDYDURYDOQDRSUHPD2EXWHY]D]DãþLWRSUHGWYHJDQMLYOLYDUQDKLQSUL
YDUMHQMXGHO=DKWHYHLQSUHVNXVQHPHWRGH]D]DãþLWRSUHGWYHJDQMLSULYDUMHQMX
LQVRURGQLKSRVWRSNLK,62
Personal protective equipment - Footwear protecting against risks in foundries and
welding - Part 2: Requirements and test methods for protection against risks in welding
and allied processes (ISO 20349-2:2017)
Persönliche Schutzausrüstung - Schuhe zum Schutz gegen Risiken in Gießereien und
beim Schweißen - Teil 2: Anforderungen und Prüfverfahren zum Schutz gegen Risiken
beim Schweißen und verwandten Verfahren (ISO 20349-2:2017)
Équipement de protection individuelle - Chaussures protegeant contre les risques dans
les fonderies et la soudure - Partie 2: Exigences et méthode d'essai pour la protection
contre les risques dans la soudure (ISO 20349-2:2017)
Ta slovenski standard je istoveten z: EN ISO 20349-2:2017
ICS:
13.340.50 Varovanje nog in stopal Leg and foot protection
SIST EN ISO 20349-2:2017 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 20349-2:2017

---------------------- Page: 2 ----------------------

SIST EN ISO 20349-2:2017


EN ISO 20349-2
EUROPEAN STANDARD

NORME EUROPÉENNE

September 2017
EUROPÄISCHE NORM
ICS 13.340.50 Supersedes EN ISO 20349:2010
English Version

Personal protective equipment - Footwear protecting
against risks in foundries and welding - Part 2:
Requirements and test methods for protection against
risks in welding and allied processes (ISO 20349-2:2017)
Équipement de protection individuelle - Chaussures de Persönliche Schutzausrüstung - Schuhe zum Schutz
protection contre les risques dans les fonderies et lors gegen Risiken in Gießereien und beim Schweißen - Teil
d'opérations de soudage - Partie 2: Exigences et 2: Anforderungen und Prüfverfahren zum Schutz gegen
méthodes d'essai pour la protection contre les risques Risiken beim Schweißen und verwandten Verfahren
lors d'opérations de soudage et techniques connexes (ISO 20349-2:2017)
(ISO 20349-2:2017)
This European Standard was approved by CEN on 12 June 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 20349-2:2017 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 20349-2:2017
EN ISO 20349-2:2017 (E)
Contents Page
European foreword . 3
Annex ZA (informative) Clauses of this European Standard addressing essential
requirements or other provisions of EU directives 89/686/EEC Personal Protective
Equipment aimed to be covered . 4

2

---------------------- Page: 4 ----------------------

SIST EN ISO 20349-2:2017
EN ISO 20349-2:2017 (E)

European foreword
This document (EN ISO 20349-2:2017) has been prepared by Technical Committee ISO/TC 94
"Personal safety - Protective clothing and equipment" in collaboration with Technical Committee
CEN/TC 161 “Foot and leg protectors” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2018 and conflicting national standards shall be
withdrawn at the latest by March 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 20349:2010.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive.
For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
the United Kingdom.
Endorsement notice
The text of ISO 20349-2:2017 has been approved by CEN as EN ISO 20349-2:2017 without any
modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 20349-2:2017
EN ISO 20349-2:2017 (E)
ANNEX ZA
(informative)

Clauses of this European Standard addressing essential requirements or
other provisions of EU directives 89/686/EEC Personal Protective
Equipment aimed to be covered
This This European Standard has been prepared under a Commission’s standardization request M/031
Personal protective equipment to provide one voluntary means of conforming to essential]
requirements of the New Approach Directive 89/686/EEC Personal Protective Equipment.
Once this standard is cited in the Official Journal of the European Union under that Directive
89/686/EEC, compliance with the normative clauses of this standard given in Table ZA.1 confers,
within the limits of the scope of this standard, a presumption of conformity with the corresponding
essential requirements of that Directive 89/686/EEC, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and EU Directive 89/686/EEC
Personal Protective Equipment
Essential Requirements of Clause(s)/sub-clause(s) of
Remarks/Notes
Directive 89/686/EEC this EN
1.1.1 Ergonomics 7.1 EN ISO 20345:2011, 5.3.4
1.2 Innocuousness of PPE 7.5
1.4 Information supplied by
9
the manufacturer
2.2 PPE enclosing the parts of EN ISO 20345:2011, 5.4.6,

the body to be protected 5.5.3
2.4 PPE subject to ageing EN ISO 20345:2011, 5.3.2.5,
7.3, 7.4
6.4.1, 6.2.3.1, 6.2.3.2 and 5.4.8
2.12 PPE bearing one or more
identification or recognition
8
marks directly or indirectly
relating to health and safety
3.1.1 Impact caused by falling
or ejected objects and EN ISO 20345: 5.3.2.3, 6.2.4,

collisions of parts of the body 6.2.6, 6.2.7, 6.4.1
with an obstacle.
3.1.2.1 Prevention of falls due
EN ISO 20345:2011, 5.3.5
to slipping
3.2 Protection against (static)
EN ISO 20345:2011, 5.3.2.4,
compression of part of the
6.2.1 and 6.2.4
body
3.3 Protection against physical
EN ISO 20345:2011, 6.2.1,
injury (abrasion, perforation,
6.2.6, 6.2.7 and 6.2.8
cuts, bites)
4

---------------------- Page: 6 ----------------------

SIST EN ISO 20349-2:2017
EN ISO 20349-2:2017 (E)

3.6 Protection against heat EN ISO 20345:2011, 6.2.3.1
7.3, 7.4
and/or fire and 6.4.1
3.7 Protection against cold EN ISO 20345:2011, 6.2.3.2
3.8 Protection against electric
EN ISO 20345:2011, 6.2.2.3
shock
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
5

---------------------- Page: 7 ----------------------

SIST EN ISO 20349-2:2017

---------------------- Page: 8 ----------------------

SIST EN ISO 20349-2:2017
INTERNATIONAL ISO
STANDARD 20349-2
First edition
2017-07
Personal protective equipment —
Footwear protecting against risks in
foundries and welding —
Part 2:
Requirements and test methods for
protection against risks in welding
and allied processes
Équipement de protection individuelle — Chaussures de protection
contre les risques dans les fonderies et lors d’opérations de soudage —
Partie 2: Exigences et méthodes d’essai pour la protection contre les
risques lors d’opérations de soudage et techniques connexes
Reference number
ISO 20349-2:2017(E)
©
ISO 2017

---------------------- Page: 9 ----------------------

SIST EN ISO 20349-2:2017
ISO 20349-2:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 20349-2:2017
ISO 20349-2:2017(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classifications of footwear . 1
5 Sampling and conditioning . 2
6 Requirements . 2
7 Specific requirements . 4
7.1 Height of upper . 4
7.2 Upper design . 4
7.3 Small molten metal splash test . 5
7.4 Burning behaviour . 5
7.5 Innocuousness . 5
8 Marking . 6
9 Information to be supplied by the manufacturer . 6
9.1 General . 6
9.2 Information regarding perforation resistant insert . 8
9.3 Electrical properties . 8
9.3.1 Antistatic footwear . 8
9.3.2 Electrically insulating footwear . 8
9.4 Insocks . 9
Bibliography .10
© ISO 2017 – All rights reserved iii

---------------------- Page: 11 ----------------------

SIST EN ISO 20349-2:2017
ISO 20349-2:2017(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: w w w . i s o .org/ iso/ foreword .html.
This document was prepared by the European Committee Standardization (CEN) Technical Committee
CEN/TC 161, Foot and leg protectors in equipment, in collaboration with ISO Technical Committe
...