iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 60439-5:1999

(Main)

Low-voltage switchgear and controlgear assemblies -- Part 5: Particular requirements for assemblies intended to be installed outdoors in public places - Cable distribution cabinets (CDCs) for power distribution in networks

Low-voltage switchgear and controlgear assemblies -- Part 5: Particular requirements for assemblies intended to be installed outdoors in public places - Cable distribution cabinets (CDCs) for power distribution in networks

Gives supplementary requirements for cable distribution cabinets (CDC), which are stationary, type-tested assemblies (TTA) for outdoor installation in places which are exposed to the public, but where only skilled persons have access to their use. They are safe for use in public three-phase systems

Niederspannung-Schaltgerätekombinationen -- Teil 5: Besondere Anforderungen an Niederspannung-Schaltgerätekombinationen, die im Freien an öffentlich zugängigen Plätzen aufgestellt werden - Kabelverteilerschränke in Energieversorgungsnetzen

Ensembles d'appareillage à basse tension -- Partie 5: Règles particulières pour les ensembles destinés à être installés à l'extérieur, en des lieux publics - Ensembles d'appareillage pour réseaux de distribution (ERD)

Fournit les exigences complémentaires pour les ensembles d'appareillage fixes pour réseaux de distribution (ERD), ensembles de série (ES) pour installation à l'extérieur, dans des emplacements au contact avec le public, mais qui ne sont accessibles pour l'utilisation que par des personnes qualifiées. Ils sont destinés à être utilisés avec des systèmes triphasés publics.

Sestavi nizkonapetostnih stikalnih in krmilnih naprav – 5. del: Posebne zahteve za sestave, predvidene za zunanjo postavitev na javnih mestih – Kabelske razdelilne omare (CDC) za elektroenergetska omrežja

General Information

Status
Withdrawn
Publication Date
30-Jun-1999
Withdrawal Date
17-Sep-2007
ICS
29.130.20 - Low voltage switchgear and controlgear
29.240.99 - Other equipment related to power transmission and distribution networks
Technical Committee
SKA - Switchgear and control gear
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
17-Sep-2007
Due Date
10-Oct-2007
Completion Date
18-Sep-2007
Directive
2006/95/EC - Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (codified version)
73/23/EEC - Electrical equipment designed for use within certain voltage limits
Ref Project
EN 60439-5:1996 - Low-voltage switchgear and controlgear assemblies - Part 5: Particular requirements for assemblies intended to be installed outdoors in public places - Cable distribution cabinets (CDCs) for power distribution in networks

Relations

Amended By
SIST EN 60439-5:1999/A1:1999 - Low-voltage switchgear and controlgear assemblies -- Part 5: Particular requirements for assemblies intended to be installed outdoors in public places - Cable distribution cabinets (CDCs) for power distribution in networks
Effective Date
21-Sep-2010
Replaced By
SIST EN 60439-5:2007 - Low-voltage switchgear and controlgear assemblies -- Part 5: Particular requirements for assemblies for power distribution in public networks
Effective Date
29-Jan-2023
Amended By
SIST EN 60439-5:1999/A1:1999 - Low-voltage switchgear and controlgear assemblies -- Part 5: Particular requirements for assemblies intended to be installed outdoors in public places - Cable distribution cabinets (CDCs) for power distribution in networks
Effective Date
28-Jan-2023
Replaced By
SIST EN 60439-5:2007 - Low-voltage switchgear and controlgear assemblies -- Part 5: Particular requirements for assemblies for power distribution in public networks
Effective Date
06-May-2014
Replaced By
SIST EN 60439-5:2007 - Low-voltage switchgear and controlgear assemblies -- Part 5: Particular requirements for assemblies for power distribution in public networks
Effective Date
07-Jun-2022
Amended By
SIST EN 60439-5:1999/A1:1999 - Low-voltage switchgear and controlgear assemblies -- Part 5: Particular requirements for assemblies intended to be installed outdoors in public places - Cable distribution cabinets (CDCs) for power distribution in networks
Effective Date
07-Jun-2022
Replaced By
SIST EN 60439-5:2007 - Low-voltage switchgear and controlgear assemblies -- Part 5: Particular requirements for assemblies for power distribution in public networks
Effective Date
01-Jan-2007

Buy Standard

EN 60439-5:1999EN 60439-5:1999
PreviousNext
Standard
EN 60439-5:1999
English language
29 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60439-5:1999
01-julij-1999
Sestavi nizkonapetostnih stikalnih in krmilnih naprav – 5. del: Posebne zahteve za
sestave, predvidene za zunanjo postavitev na javnih mestih – Kabelske razdelilne
omare (CDC) za elektroenergetska omrežja
Low-voltage switchgear and controlgear assemblies -- Part 5: Particular requirements for
assemblies intended to be installed outdoors in public places - Cable distribution
cabinets (CDCs) for power distribution in networks
Niederspannung-Schaltgerätekombinationen -- Teil 5: Besondere Anforderungen an
Niederspannung-Schaltgerätekombinationen, die im Freien an öffentlich zugängigen
Plätzen aufgestellt werden - Kabelverteilerschränke in Energieversorgungsnetzen
Ensembles d'appareillage à basse tension -- Partie 5: Règles particulières pour les
ensembles destinés à être installés à l'extérieur, en des lieux publics - Ensembles
d'appareillage pour réseaux de distribution (ERD)
Ta slovenski standard je istoveten z: EN 60439-5:1996
ICS:
29.130.20 Nizkonapetostne stikalne in Low voltage switchgear and
krmilne naprave controlgear
29.240.99 'UXJDRSUHPDY]YH]L] Other equipment related to
RPUHåML]DSUHQRVLQ power transmission and
GLVWULEXFLMRHOHNWULþQHHQHUJLMH distribution networks
SIST EN 60439-5:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60439-5:1999

---------------------- Page: 2 ----------------------

SIST EN 60439-5:1999

---------------------- Page: 3 ----------------------

SIST EN 60439-5:1999

---------------------- Page: 4 ----------------------

SIST EN 60439-5:1999

---------------------- Page: 5 ----------------------

SIST EN 60439-5:1999

---------------------- Page: 6 ----------------------

SIST EN 60439-5:1999

---------------------- Page: 7 ----------------------

SIST EN 6043
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 61439-5:2015/AC:2016(Corrigendum)
Low-voltage switchgear and controlgear assemblies - Part 5: Assemblies for power distribution in public networks
EN 61439-5:2015/AC:2015

IEC Corrigendum only

  • Corrigendum
    1 page
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61439-5:2015(Main)
Low-voltage switchgear and controlgear assemblies - Part 5: Assemblies for power distribution in public networks (IEC 61439-5:2014)
EN 61439-5:2015

This part of IEC 61439 defines the specific requirements for public electricity network
distribution assemblies (PENDAs).
PENDAs have the following criteria:
– used for the distribution of electrical energy in three phase systems for which the rated
voltage does not exceed 1 000 V a.c. (see Figure 101 for a typical distribution network);
– stationary;
– open ASSEMBLIES are not covered by this standard;
– suitable for installation in places where only skilled persons have access for their use,
however, outdoor types may be installed in situations that are accessible to ordinary
persons;
– for indoor or outdoor use.
The object of this standard is to state the definitions and to specify the service conditions,
construction requirements, technical characteristics and tests for PENDAs. Network
parameters may require tests at higher performance levels.
PENDAs may also include control and or signalling devices associated with the distribution of
electrical energy.
This standard applies to all PENDAs whether they are designed, manufactured on a one-off
basis or fully standardised and manufactured in quantity.
The manufacture and/or assembly may be carried out other than by the original manufacturer
(see 3.10.1 of IEC 61439-1:2011).
This standard does not apply to individual devices and self-contained components, such as
motor starters, fuse switches, electronic equipment, etc. which comply with the relevant
product standards.
This standard does not apply to specific types of ASSEMBLIES covered by other parts of
IEC 61439 series.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard – translation
    38 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day
SIST
kSIST FprEN IEC 61439-5:2023(Main)
Low-voltage switchgear and controlgear assemblies - Part 5: Assemblies for power distribution in public networks
FprEN IEC 61439-5:2023

IEC 61439-5:2023 is available as IEC 61439-5:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.

IEC 61439-5:2023 defines the specific requirements for public electricity network distribution assemblies (PENDAs). PENDAs have the following criteria:
- used for the distribution of electrical energy in three phase systems for which the rated voltage does not exceed 1 000 V AC (see Figure 101 for a typical distribution network) and DC systems not exceeding 1 500 V DC;
- stationary;
- open type assemblies are not covered by this document;
- suitable for installation in places where only skilled persons have access for their use, however, outdoor types can be installed in situations that are accessible to ordinary persons
- intended for use in energy distribution in public power grids;
- indoor use: assemblies for installation inside of electric power substations;
- outdoor use: assemblies containing an enclosure suitable for open air installation.
This third edition cancels and replaces the second edition published in 2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) omission of the requirement to conduct mechanical tests at -25 °C when enclosures are made of a metallic material;
b) addition of assumed loading factors generation supplies and electric vehicle charging applications;
c) additional dielectric tests when a PENDA is used in a distribution substation with separate HV and LV earths;
d) further clarification of representative samples for design verification.

  • Draft
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61439-5:2015/AC:2016(Corrigendum)
Low-voltage switchgear and controlgear assemblies - Part 5: Assemblies for power distribution in public networks
EN 61439-5:2015/AC:2015

IEC Corrigendum only

  • Corrigendum
    1 page
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61439-5:2015(Main)
Low-voltage switchgear and controlgear assemblies - Part 5: Assemblies for power distribution in public networks (IEC 61439-5:2014)
EN 61439-5:2015

This part of IEC 61439 defines the specific requirements for public electricity network
distribution assemblies (PENDAs).
PENDAs have the following criteria:
– used for the distribution of electrical energy in three phase systems for which the rated
voltage does not exceed 1 000 V a.c. (see Figure 101 for a typical distribution network);
– stationary;
– open ASSEMBLIES are not covered by this standard;
– suitable for installation in places where only skilled persons have access for their use,
however, outdoor types may be installed in situations that are accessible to ordinary
persons;
– for indoor or outdoor use.
The object of this standard is to state the definitions and to specify the service conditions,
construction requirements, technical characteristics and tests for PENDAs. Network
parameters may require tests at higher performance levels.
PENDAs may also include control and or signalling devices associated with the distribution of
electrical energy.
This standard applies to all PENDAs whether they are designed, manufactured on a one-off
basis or fully standardised and manufactured in quantity.
The manufacture and/or assembly may be carried out other than by the original manufacturer
(see 3.10.1 of IEC 61439-1:2011).
This standard does not apply to individual devices and self-contained components, such as
motor starters, fuse switches, electronic equipment, etc. which comply with the relevant
product standards.
This standard does not apply to specific types of ASSEMBLIES covered by other parts of
IEC 61439 series.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard – translation
    38 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day
SIST
kSIST FprEN IEC 61439-5:2023(Main)
Low-voltage switchgear and controlgear assemblies - Part 5: Assemblies for power distribution in public networks
FprEN IEC 61439-5:2023

IEC 61439-5:2023 is available as IEC 61439-5:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.

IEC 61439-5:2023 defines the specific requirements for public electricity network distribution assemblies (PENDAs). PENDAs have the following criteria:
- used for the distribution of electrical energy in three phase systems for which the rated voltage does not exceed 1 000 V AC (see Figure 101 for a typical distribution network) and DC systems not exceeding 1 500 V DC;
- stationary;
- open type assemblies are not covered by this document;
- suitable for installation in places where only skilled persons have access for their use, however, outdoor types can be installed in situations that are accessible to ordinary persons
- intended for use in energy distribution in public power grids;
- indoor use: assemblies for installation inside of electric power substations;
- outdoor use: assemblies containing an enclosure suitable for open air installation.
This third edition cancels and replaces the second edition published in 2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) omission of the requirement to conduct mechanical tests at -25 °C when enclosures are made of a metallic material;
b) addition of assumed loading factors generation supplies and electric vehicle charging applications;
c) additional dielectric tests when a PENDA is used in a distribution substation with separate HV and LV earths;
d) further clarification of representative samples for design verification.

  • Draft
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CEN/TR 12349:2023(Main)
Mechanical vibration - Guide to the health effects of vibration on the human body
CEN/TR 12349:2023

The aim of this CEN report is to provide information on the possible adverse health effects caused by exposure to vibration at work.  the report addresses manufacturers as well as employers and employees using vibrating machinery in order to improve their understanding of the possible health problems arising from occupational exposure to vibration.

  • Technical report
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 80004-1:2023(Main)
Nanotechnologies - Vocabulary - Part 1: Core vocabulary (ISO 80004-1:2023)
EN ISO 80004-1:2023

This document defines core terms in the field of nanotechnology. This document is intended to facilitate communication between organizations and individuals in industry and those who interact with them.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 3262-4:2023(Main)
Extenders - Specifications and methods of test - Part 4: Whiting (ISO 3262-4:2022)
EN ISO 3262-4:2023

This document specifies requirements and corresponding methods of test for whiting.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 1247-1:2023(Main)
Aluminium pigments for paints - Part 1: General aluminium pigments (ISO 1247-1:2021)
EN ISO 1247-1:2023

This document specifies the requirements and corresponding test methods for aluminium pigments suitable for use in paints including:
a) general, decorative and protective paints, and
b) special finishing paints.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day