SIST EN ISO 5167-3:2020

Oznaka standarda: SIST EN ISO 5167-3:2020
Koda projekta: CSF05030
Organizacija: SIST
Naslov (angleški): Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 3: Nozzles and Venturi nozzles (ISO 5167-3:2019)
Naslov (slovenski): Merjenje pretoka fluida na osnovi tlačne razlike, povzročene z napravo, vstavljeno v polno zapolnjen vod s krožnim prerezom - 3. del: Šobe in Venturijeve šobe (ISO 5167-3:2020)
Če kupite standardizacijski dokument v .pdf formatu prek spletne prodaje, vam nudimo 20% popust pri spodnji ceni brez DDV. Cenik SIST
Dokumenti
Ime Jezik Status Cena Dodaj v košarico
SIST EN ISO 5167-3:2020 angleški jezik Active SIST-J: 96.80 EUR
PDF
Papir
Tehnični odbor: IMIN - Merilni instrumenti
ICS: 17.120.10
Status: Objavljen
Objavljen: 01-Nov-2020
Refer. št. objave: Sporocila 2020-11
Referenčna oznaka: EN ISO 5167-3:2020
Področje projekta (angleško): This document specifies the geometry and method of use (installation and operating conditions) of nozzles and Venturi nozzles when they are inserted in a conduit running full to determine the flowrate of the fluid flowing in the conduit. This document also provides background information for calculating the flowrate and is applicable in conjunction with the requirements given in ISO 5167-1. This document is applicable to nozzles and Venturi nozzles in which the flow remains subsonic throughout the measuring section and where the fluid can be considered as single-phase. In addition, each of the devices can only be used within specified limits of pipe size and Reynolds number. It is not applicable to the measurement of pulsating flow. It does not cover the use of nozzles and Venturi nozzles in pipe sizes less than 50 mm or more than 630 mm, or where the pipe Reynolds numbers are below 10 000. This document deals with a) three types of standard nozzles: 1) ISA 19325) nozzle; 2) the long radius nozzle6); 3) the throat-tapped nozzle b) the Venturi nozzle. The three types of standard nozzle are fundamentally different and are described separately in this document. The Venturi nozzle has the same upstream face as the ISA 1932 nozzle, but has a divergent section and, therefore, a different location for the downstream pressure tappings, and is described separately. This design has a lower pressure loss than a similar nozzle. For all of these nozzles and for the Venturi nozzle direct calibration experiments have been made, sufficient in number, spread and quality to enable coherent systems of application to be based on their results and coefficients to be given with certain predictable limits of uncertainty.
Povezava na standarde
Povezava Ime Datum
Nadomešča SIST EN ISO 5167-3:2004 - Merjenje pretoka fluida na osnovi tlačne razlike, povzročene z napravo, vstavljeno v polno zapolnjen vod s krožnim prerezom – 3. del: Šobe in Venturijeve šobe (ISO 5167-3:2003) 01-Nov-2020


• Slovenski standardi SIST s cenovnim razredom AC so popravki standardov in so v večini primerov brezplačni.

• Slovenski standardi SIST s cenovnim razredom AP so privzeti tuji standardi, katerih sestavni del je izvirni standard, ki ga moramo pridobiti pri izdajatelju v tujini. Naročilo pošljite na: prodaja@sist.si.

Najbolje prodajani standardi