SIST EN IEC 61340-5-3:2022

SLOVENSKI STANDARD
SIST EN IEC 61340-5-3:2022
01-september-2022
Nadomešča:
SIST EN 61340-5-3:2015
Elektrostatika - 5-3. del: Zaščita elektronskih naprav pred elektrostatičnimi pojavi -
Lastnosti in klasifikacija zahtev za embalažo naprav, ki so občutljive za
elektrostatične razelektritve (IEC 61340-5-3:2022)
Electrostatics - Part 5-3: Protection of electronic devices from electrostatic phenomena -
Properties and requirements classification for packaging intended for electrostatic
discharge sensitive devices (IEC 61340-5-3:2022)
Elektrostatik - Teil 5-3: Schutz von elektronischen Bauelementen gegen elektrostatische
Phänomene - Eigenschaften und Anforderungen für die Klassifizierung von
Verpackungen, welche für Bauelemente verwendet werden, die gegen elektrostatische
Entladungen empfindlich sind (IEC 61340-5-3:2022)
Electrostatique - Partie 5-3: Protection des dispositifs électroniques contre les
phénomènes électrostatiques - Classification des propriétés et des exigences relatives à
l'emballage destiné aux dispositifs sensibles aux décharges électrostatiques (IEC 61340-
5-3:2022)
Ta slovenski standard je istoveten z: EN IEC 61340-5-3:2022
ICS:
17.220.99 Drugi standardi v zvezi z Other standards related to
elektriko in magnetizmom electricity and magnetism
SIST EN IEC 61340-5-3:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 61340-5-3:2022

---------------------- Page: 2 ----------------------
SIST EN IEC 61340-5-3:2022


EUROPEAN STANDARD EN IEC 61340-5-3

NORME EUROPÉENNE

EUROPÄISCHE NORM June 2022
ICS 17.220.99; 29.020 Supersedes EN 61340-5-3:2015
English Version
Electrostatics - Part 5-3: Protection of electronic devices from
electrostatic phenomena - Properties and requirements
classification for packaging intended for electrostatic discharge
sensitive devices
(IEC 61340-5-3:2022)
Electrostatique - Partie 5-3: Protection des dispositifs Elektrostatik - Teil 5-3: Schutz von elektronischen
électroniques contre les phénomènes électrostatiques - Bauelementen gegen elektrostatische Phänomene -
Classification des propriétés et des exigences relatives à Eigenschaften und Anforderungen für die Klassifizierung
l'emballage destiné aux dispositifs sensibles aux décharges von Verpackungen, welche für Bauelemente verwendet
électrostatiques werden, die gegen elektrostatische Entladungen
(IEC 61340-5-3:2022) empfindlich sind
(IEC 61340-5-3:2022)
This European Standard was approved by CENELEC on 2022-06-01. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 61340-5-3:2022 E

---------------------- Page: 3 ----------------------
SIST EN IEC 61340-5-3:2022
EN IEC 61340-5-3:2022 (E)
European foreword
The text of document 101/649/FDIS, future edition 3 of IEC 61340-5-3, prepared by IEC/TC 101
"Electrostatics" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN IEC 61340-5-3:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-03-01
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-06-01
document have to be withdrawn
This document supersedes EN 61340-5-3:2015 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61340-5-3:2022 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 61340-5-1 NOTE Harmonized as EN 61340-5-1
2

---------------------- Page: 4 ----------------------
SIST EN IEC 61340-5-3:2022
EN IEC 61340-5-3:2022 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61340-2-3 - Electrostatics - Part 2-3: Methods of test for EN 61340-2-3 -
determining the resistance and resistivity of
solid materials used to avoid electrostatic
charge accumulation
IEC 61340-4-8 - Electrostatics - Part 4-8: Standard test EN 61340-4-8 -
methods for specific applications -
Electrostatic discharge shielding - Bags

3

---------------------- Page: 5 ----------------------
SIST EN IEC 61340-5-3:2022

---------------------- Page: 6 ----------------------
SIST EN IEC 61340-5-3:2022



IEC 61340-5-3

®


Edition 3.0 2022-04




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Electrostatics –

Part 5-3: Protection of electronic devices from electrostatic phenomena –

Properties and requirements classification for packaging intended for


electrostatic discharge sensitive devices



Électrostatique –


Partie 5-3: Protection des dispositifs électroniques contre les phénomènes

électrostatiques – Classification des propriétés et des exigences relatives à

l'emballage destiné aux dispositifs sensibles aux décharges électrostatiques










INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 17.220.99; 29.020 ISBN 978-2-8322-1100-5




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------
SIST EN IEC 61340-5-3:2022
– 2 – IEC 61340-5-3:2022  IEC 2022
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions and abbreviated terms . 7
3.1 Terms and definitions . 7
3.2 Abbreviated terms . 9
4 Tailoring . 9
5 Packaging application requirement . 9
5.1 General . 9
5.2 Inside an EPA . 9
5.3 Outside an EPA . 9
6 Classification of ESD packaging material properties . 10
6.1 General . 10
6.2 Material resistance properties . 10
6.2.1 General . 10
6.2.2 Resistance of conductive materials . 10
6.2.3 Resistance of dissipative materials . 10
6.2.4 Resistance of insulating materials. 11
6.3 Material electrostatic shielding properties . 11
6.3.1 Electrostatic discharge shielding . 11
6.3.2 Electrostatic field shielding . 11
7 Technical requirements for ESD protective packaging . 11
7.1 Packaging and material properties . 11
7.2 Packaging marking . 12
7.2.1 Classification symbol . 12
7.2.2 Packaging classification. 13
7.2.3 Traceability . 13
Annex A (informative) Guidance on ESD packaging material . 14
A.1 Environment and device sensitivity . 14
A.1.1 General . 14
A.1.2 Environment . 14
A.1.3 Device sensitivity . 15
A.2 Equipotential bonding . 16
A.3 Dissipative material for intimate contact . 16
A.4 Packaging from incoming material to the point of use . 16
A.5 Periodic verification . 17
A.6 Examples of measurement procedures for qualification and verification of
packaging . 18
Annex B (informative) Device damage . 20
B.1 Damage from ESD . 20
B.2 Discharge to a device . 20
B.2.1 Discharge to device from external objects . 20
B.2.2 Retained charge on a packaging . 20
B.3 Discharge from a floating device (CDM) . 20

---------------------- Page: 8 ----------------------
SIST EN IEC 61340-5-3:2022
IEC 61340-5-3:2022  IEC 2022 – 3 –
B.3.1 Discharges from devices in an electric field . 20
B.3.2 Discharges from tribo-electrified devices . 20
Annex C (informative) Guidance on electric field shielding . 21
Annex D (informative) Low charging material property . 22
Bibliography . 23

Figure 1 – Example of packaging label (*Primary function code) . 13
Figure A.1 – Examples of EPA configurations . 15
Figure A.2 – Application of ESD protective packaging . 17

Table 1 – Test methods for electrostatic protective packaging . 12
Table 2 – Test methods and requirements for electrostatic discharge shielding
packaging . 12
Table 3 – Primary function code and ESD classification symbol . 13
Table A.1 – Packaging characteristics for environmental consideration . 14
Table A.2 – Examples of qualification and verification of packaging . 18

---------------------- Page: 9 ----------------------
SIST EN IEC 61340-5-3:2022
– 4 – IEC 61340-5-3:2022  IEC 2022
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

ELECTROSTATICS –

Part 5-3: Protection of electronic devices from electrostatic phenomena –
Properties and requirements classification for packaging intended for
electrostatic discharge sensitive devices

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 61340-5-3 has been prepared by IEC technical committee 101: Electrostatics. It is an
International Standard.
This third edition cancels and replaces the second edition published in 2015. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
1 2
a) reference to IEC 61340-4-10 [1] was removed;
b) material resistance property "electrostatic field shielding" was removed;
_____________
1
Withdrawn.
2
Numbers in square brackets refer to the bibliography.

---------------------- Page: 10 ----------------------
SIST EN IEC 61340-5-3:2022
IEC 61340-5-3:2022  IEC 2022 – 5 –
c) the requirement for electrostatic discharge shielding was changed from 50 nJ to 20 nJ;
d) Table 1 – footnote "b" was changed to mention the two-point probe in IEC 61340-2-3;
e) "shall be marked" was changed to "should be marked" in 7.2.2 and 7.2.3;
f) Table 3 – the classification symbol and the primary function code F was removed;
g) Table A.2 – references to IEC TS 61340-5-4 [2] and IEC TR 61340-5-5 [3] were added;
h) Annex C – guidance regarding electric field shielding was added;
i) Annex D – low charging material property was added.
The text of this International Standard is based on the following documents:
Draft Report on voting
101/649/FDIS 101/660/RVD

Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/standardsdev/publications.
A list of all parts in the IEC 61340 series, published under the general title Electrostatics, can
be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 11 ----------------------
SIST EN IEC 61340-5-3:2022
– 6 – IEC 61340-5-3:2022  IEC 2022
INTRODUCTION
Packaging is necessary to protect electrostatic discharge sensitive devices (ESDSs) from static
electricity and electrostatic discharge (ESD) damage as well as physical and environmental
damage during manufacture, transportation and storage.

---------------------- Page: 12 ----------------------
SIST EN IEC 61340-5-3:2022
IEC 61340-5-3:2022  IEC 2022 – 7 –
ELECTROSTATICS –

Part 5-3: Protection of electronic devices from electrostatic phenomena –
Properties and requirements classification for packaging intended for
electrostatic discharge sensitive devices



1 Scope
This part of IEC 61340 defines the ESD protective packaging properties required to protect ESD
sensitive devices (ESDSs) through all phases of production, rework and maintenance, transport
and storage. Test methods are referenced to evaluate packaging and packaging materials for
these product and material properties. Performance limits are provided.
This document does not address protection from electromagnetic interference (EMI),
electromagnetic pulsing (EMP) or protection of electrically initiated explosive materials or
devices.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies.
For undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 61340-2-3, Electrostatics – Part 2-3: Methods of test for determining the resistance and
resistivity of solid materials used to avoid electrostatic charge accumulation
IEC 61340-4-8, Electrostatics – Part 4-8: Standard test methods for specific applications –
Electrostatic discharge shielding – Bags
3 Terms, definitions and abbreviated terms
3.1 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1.1
electrostatic discharge
ESD
rapid transfer of charge between bodies at different electrostatic potentials

---------------------- Page: 13 ----------------------
SIST EN IEC 61340-5-3:2022
– 8 – IEC 61340-5-3:2022  IEC 2022
3.1.2
ESD sensitive device
ESDS
sensitive device, integrated circuit or assembly that can be damaged by electrostatic fields or
electrostatic discharge
Note 1 to entry: See Clause B.2 and Clause B.3 in Annex B.
3.1.3
ESD protected area
EPA
area in which an ESDS can be handled with acceptable risk of damage caused by electrostatic
discharge or fields
SEE: Figure A.1 in Annex A.
3.1.4
unprotected area
UPA
area outside an EPA
SEE: Figure A.1 in Annex A.
3.1.5
intimate packaging
material which makes contact with an ESDS
3.1.6
proximity packaging
material not making contact with an ESDS and which is used to enclose one or more devices
3.1.7
secondary packaging
material used primarily to give additional physical protection to the outside of proximity
packaging
3.1.8
volume resistance
R
V
ratio of a DC voltage (V) applied between two electrodes placed on two (opposite) surfaces of
a specimen and the current (A) between the electrodes
Note 1 to entry: Volume resistance is expressed in Ω.
3.1.9
point-to-point resistance
R
p-p
ratio of a DC voltage (V) applied between two electrodes on a surface of a specimen and the
current (A) between the electrodes
Note 1 to entry: The electrode configuration for point-to-point resistance measurements is usually a pair of circular
faced electrodes with a defined distance apart.
Note 2 to entry: Point-to-point resistance is expressed in Ω.

---------------------- Page: 14 ----------------------
SIST EN IEC 61340-5-3:2022
IEC 61340-5-3:2022  IEC 2022 – 9 –
3.1.10
surface resistance
R
S
ratio of a DC voltage (V) applied between two electrodes in a defined configuration on a surface
of a specimen and the current (A) between the electrodes
Note 1 to entry: The electrode configuration for surface resistance measurement is usually a pair of parallel
rectangular electrodes or a pair of circular concentric electrodes.
Note 2 to entry: Surface resistance is expressed in Ω.
3.2 Abbreviated terms
CDM charged device model
EMI electromagnetic interference
EMP electromagnetic pulsing
EPA ESD protected area
ESD electrostatic discharge
ESDS electrostatic discharge sensitive device
HBM human body model
UPA unprotected area
4 Tailoring
This document, or portions thereof, does not necessarily apply to all applications. Tailoring is
accomplished by evaluating the applicability of each requirement for the specific application.
Upon completion of the evaluation, requirements may be added, modified or deleted.
Tailoring decisions, including rationale, shall be documented.
5 Packaging application requirement
5.1 General
Transportation and storage of ESDSs require packaging that provides protection from
electrostatic hazards (for example from an electrostatic discharge). Within an EPA in which all
ESD risks are well controlled, it is possible that ESD protective packaging will not be necessary.
5.2 Inside an EPA
Packaging used within an EPA shall consist of dissipative or conductive materials for intimate
contact.
Additional protection can be necessary for items sensitive to < 100 V for HBM, < 200 V for CDM
and < 35 V for isolated conductors, depending on application and program plan requirements.
NOTE Dissipative materials are preferred for intimate packaging in situations where charged device model (CDM)
damage is a concern.
5.3 Outside an EPA
Transportation and storage of sensitive products outside of an EPA shall be done in packaging
that provides both
a) dissipative or conductive materials for intimate contact,
b) a structure that provides electrostatic discharge shielding.

---------------------- Page: 15 ----------------------
SIST EN IEC 61340-5-3:2022
– 10 – IEC 61340-5-3:2022  IEC 2022
If electrostatic field shielding materials are used to provide discharge shielding, a material that
provides a barrier to current flow should be used in combination with the electrostatic field
shielding material.
NOTE Dissipative materials are preferred for intimate packaging in situations where charged device model (CDM)
damage is a concern.
6 Classification of ESD packaging material properties
6.1 General
Materials and packaging that are useful in preventing damage to ESD sensitive devices exhibit
certain properties. These properties include:
a) resistance properties:
– conductive;
– dissipative;
b) shielding properties:
– electrostatic discharge;
– electrostatic field;
c) low charging properties:
See Annex D.
6.2 Material resistance properties
6.2.1 General
Most standard packaging materials are electrically insulating and insulating materials retain
charge. Making the packaging less insulating provides a path for the charge to dissipate from
the packaging to a material at a lower potential.
Specific ranges of resistance are useful for different purposes. Packaging can be classified by
these resistance ranges of the material used in its construction.
6.2.2 Resistance of conductive materials
Conductive materials can be surface conductive, volume conductive or both.
a) Surface conductive materials
4
Surface conductive materials shall have a surface resistance of < 1 × 10 Ω.
b) Volume conductive materials
4
Volume conductive materials shall have a volume resistance of < 1 × 10 Ω.
NOTE The thickness of the material can have a significant influence on the measured value of volume resistance.
6.2.3 Resistance of dissipative materials
Dissipative materials can be surface dissipative, volume dissipative or both.
a) Surface dissipative materials
4 11
Surface dissipative materials shall have a surface resistance ≥ 1 × 10 and < 1 × 10 Ω.
b) Volume dissipative materials
4 11
Volume dissipative materials shall have a volume resistance ≥ 1 × 10 and < 1 × 10 Ω.
NOTE The thickness of the material can have a significant influence on the measured value of volume resistance.

---------------------- Page: 16 ----------------------
SIST EN IEC 61340-5-3:2022
IEC 61340-5-3:2022  IEC 2022 – 11 –
6.2.4 Resistance of insulating materials
Electrostatic insulating materials can be surface insulating, volume insulating or both.
a) Surface insu
...