SIST EN 1547:2001/kprA1:2009

SLOVENSKI STANDARD
SIST EN 1547:2001/kprA1:2009
01-februar-2009
,QGXVWULMVNDWHUPRSURFHVQDRSUHPD3RVWRSHNPHUMHQMDKUXSDLQGXVWULMVNH
WHUPRSURFHVQHRSUHPHLQSULSDGDMRþHSRPRåQHRSUHPH
Industrial thermoprocessing equipment - Noise test code for industrial thermoprocessing
equipment including its ancillary handling equipment
Industrielle Thermoprozessanlagen - Geräuschmessverfahren für industrielle
Thermoprozessanlagen einschließlich ihrer Be- und Entladeeinrichtungen
Equipements thermiques industriels - Code d'essai acoustique pour équipements
thermiques industriels, y compris les équipements de manutention auxiliaires
Ta slovenski standard je istoveten z: EN 1547:2001/prA1
ICS:
17.140.20 Emisija hrupa naprav in Noise emitted by machines
opreme and equipment
25.180.01 ,QGXVWULMVNHSHþLQDVSORãQR Industrial furnaces in general
SIST EN 1547:2001/kprA1:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 1547:2001/kprA1:2009

---------------------- Page: 2 ----------------------

SIST EN 1547:2001/kprA1:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 1547:2001
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
November 2008
ICS 25.180.01

English Version
Industrial thermoprocessing equipment - Noise test code for
industrial thermoprocessing equipment including its ancillary
handling equipment
Equipements thermiques industriels - Code d'essai Industrielle Thermoprozessanlagen -
acoustique pour équipements thermiques industriels, y Geräuschmessverfahren für industrielle
compris les équipements de manutention auxiliaires Thermoprozessanlagen einschließlich ihrer Be- und
Entladeeinrichtungen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 186.
This draft amendment A1, if approved, will modify the European Standard EN 1547:2001. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1547:2001/prA1:2008: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 1547:2001/kprA1:2009
EN 1547:2001/prA1:2008 (E)
Contents Page
Foreword.3
1 Modification to the Foreword .4
2 Modification to Clause 1, Scope.4
3 Modification to Clause 2, Normative references .4
4 Modification to 5.1, Basic international standards to be used .5
5 Modification to Clause 12, Declaration and verification of noise emission values .5
6 Modification to Annex ZA .5
7 Modification to Annex ZB .6
8 Addition of Bibliography.7


2

---------------------- Page: 4 ----------------------

SIST EN 1547:2001/kprA1:2009
EN 1547:2001/prA1:2008 (E)
Foreword
This document (EN 1547:2001/prA1:2008) has been prepared by Technical Committee CEN/TC 186
“Industrial thermoprocessing - Safety”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directives.
For relationship with EU Directives, see informative Annexes ZA and ZB, which are integral parts of this
document.
The new safety requirements as stated in this document comply with the additional relevant Essential
Requirements of the new Machinery Directive 2006/42/EC complementing the existing Machinery Directive
98/37/EC.
Once this document is cited in the Official Journal of the European Community under the new Machinery
Directive 2006/42/EC and has been implemented as a national standard in at least one member state, it
confers a presumption of conformity with the new relevant Essential Requirements of that new Directive and
associated EFTA regulations.
This standard forms one part of a series safety standards covering Industrial Thermoprocessing Equipment.
The full list of parts of EN 746 is given below:
EN 746 Industrial thermoprocessing equipment
Part 1: Common safety requirements for industrial thermoprocessing equipment
Part 2: Safety requirements for combustion and fuel handling systems
Part 3: Safety requirements for the generation and use of atmosphere gases
Part 4: Particular safety requirements for hot dip galvanising thermoprocessing equipment
Part 5: Particular safety requirements for salt bath thermoprocessing equipment
Part 6: Particular Safety Requirements for Material Melting, Remelting and Liquid Phase
Maintaining Thermoprocessing Equipment
Part 7: Particular Safety Requirements for Vacuum Thermoprocessing Equipment
Part 8: Particular safety requirements for quenching equipment
EN 1547 Industrial thermoprocessing equipment — Noise test code for industrial thermoprocessing
equipment including its ancillary handling equipment
An assessment of the foreseeable risks arising from the use of the equipment was carried out when this
standard was prepared.

3

---------------------- Page: 5
...