SIST EN 13523-1:2017
(Main)Coil coated metals - Test methods - Part 1: Film thickness
Coil coated metals - Test methods - Part 1: Film thickness
This part of EN 13523 specifies the procedures for determining the dry-film thickness of an organic coating on a metallic substrate (coil coating).
Four appropriate methods are given in this European Standard:
a) magnetic induction;
b) eddy current;
c) micrometer;
d) optical.
The methods are applicable only to products with smooth and flat substrates but the coating itself may be textured. In that case, for methods a) and b) the average of a series of readings will represent an average of the thickness of the organic coating, while method c) will give the maximum thickness and method d) can provide the minimum, maximum and average thickness.
Non-destructive continuous-web methods on measurement of dry-film thickness (see EN ISO 2808) are not dealt with.
Bandbeschichtete Metalle - Prüfverfahren - Teil 1: Schichtdicke
Dieser Teil der Normenreihe EN 13523 legt die Verfahren zum Bestimmen der Trockenschichtdicke einer organischen Beschichtung auf einem metallischen Substrat (Bandbeschichtung) fest.
Vier geeignete Verfahren werden in dieser Europäischen Norm angegeben:
a) Magnetoinduktion;
b) Wirbelstrom;
c) Messschraube;
d) optisch.
Die Verfahren sind nur auf Produkte mit glatten und ebenen Oberflächen anwendbar, die Beschichtung darf aber strukturiert sein. In diesem Fall stellt bei den Verfahren a) und b) der Mittelwert einer Reihe von Messungen einen Durchschnittswert der Dicke der organischen Beschichtung dar, während bei Verfahren c) die maximale Schichtdicke und bei Verfahren d) die minimale, maximale und durchschnittliche Schichtdicke angegeben wird.
Nicht zerstörende Verfahren zum Messen der Trockenschichtdicke (siehe EN ISO 2808) für Endlosbahnen werden nicht behandelt.
Tôles prélaquées - Méthodes d'essai - Partie 1 : Epaisseur du revêtement
La présente partie de l'EN 13523 prescrit les méthodes de détermination de l’épaisseur de feuil sec d’un revêtement organique sur un subjectile métallique (prélaquage).
Quatre méthodes appropriées sont décrites dans la présente Norme européenne :
a) induction magnétique ;
b) courants de Foucault ;
c) micromètre ;
d) optique.
Ces méthodes s’appliquent seulement aux produits qui comprennent des subjectiles lisses et plats, le revêtement lui-même pouvant être texturé. Dans ce cas, pour les méthodes a) et b), la moyenne d’une série de valeurs de lecture représentera une moyenne de l’épaisseur du revêtement organique, tandis que la méthode c) donnera l’épaisseur maximale et que la méthode d) fournira les épaisseurs minimales, maximales et moyennes.
Les méthodes non destructives sur toiles continues visant à déterminer l’épaisseur de feuil sec (voir l’EN ISO 2808) ne sont pas abordées dans le présent document.
Prevlečene kovine, ki se navijajo - Preskusne metode - 1. del: Debelina premaza
Ta del standarda EN 13523 določa postopke za ugotavljanje debeline suhega premaza organske prevleke na kovinski podlagi (prevleke kovin, ki se navijajo).
V tem evropskem standardu so podane štiri ustrezne metode.
a) magnetna indukcija;
b) vrtinčni tok;
c) mikrometer;
d) optična metoda.
Metode se uporabljajo samo za proizvode z gladko in ravno podlago, medtem ko je lahko prevleka teksturirana. V tem primeru bo za metodi a) in b) povprečje niza odčitkov odražalo povprečno debelino organske prevleke, metoda c) bo podala največjo debelino, metoda d) pa bo podala najmanjšo, največjo in povprečno debelino.
Ta dokument ne obravnava neporušitvenih metod z neprekinjeno mrežo za merjenje debeline suhega premaza (glej standard EN ISO 2808).
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bandbeschichtete Metalle - Prüfverfahren - Teil 1: SchichtdickeTôles prélaquées - Méthodes d'essai - Partie 1 : Epaisseur du revêtementCoil coated metals - Test methods - Part 1: Film thickness25.220.60Organske prevlekeOrganic coatings17.040.20Lastnosti površinProperties of surfacesICS:Ta slovenski standard je istoveten z:EN 13523-1:2017SIST EN 13523-1:2017en,fr,de01-maj-2017SIST EN 13523-1:2017SLOVENSKI
STANDARDSIST EN 13523-1:20101DGRPHãþD
SIST EN 13523-1:2017
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13523-1
February
t r s y ICS
s yä r v rä t râ
t wä t t rä x r Supersedes EN
s u w t uæ sã t r r {English Version
Coil coated metals æ Test methods æ Part
sã Film thicknessTôles prélaquées æ Méthodes d 5essai æ Partie
s ã Épaisseur du revêtement
Bandbeschichtete Metalle æ Prüfverfahren æ Teil
sã Schichtdicke This European Standard was approved by CEN on
s z December
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s u w t uæ sã t r s y ESIST EN 13523-1:2017
EN 13523-1:2017 (E) 2 Contents Page European foreword . 3 1 Scope . 5 2 Normative references . 5 3 Terms and definitions . 5 4 Principle . 5 4.1 Method A: Measurement on a magnetic substrate – magnetic induction . 5 4.2 Method B: Measurement on a non-magnetic substrate – eddy current . 6 4.3 Method C: Measurement on all substrates – micrometer method . 6 4.4 Method D: Measurement on all substrates – optical method . 6 5 Apparatus and materials . 6 6 Sampling . 6 7 Test panels . 6 8 Procedure. 6 8.1 Calibration . 6 8.1.1 General . 6 8.1.2 Calibration standards . 7 8.2 Scale rating . 7 8.3 Measurement . 7 8.3.1 Ambient conditions . 7 8.3.2 Number of measurements . 7 8.3.3 Method A: Magnetic induction . 7 8.3.4 Method B: Eddy current . 8 8.3.5 Method C: Micrometer method . 8 8.3.6 Method D: Optical method . 8 9 Expression of results . 9 10 Accuracy . 9 11 Test report . 9 Bibliography . 10
SIST EN 13523-1:2017
EN 13523-1:2017 (E) 3 European foreword This document (EN 13523-1:2017) has been prepared by Technical Committee CEN/TC 139 “Paints and varnishes”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2017, and conflicting national standards shall be withdrawn at the latest by August 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13523-1:2009. The main changes are: a) a reference to EN 13523-0 concerning conditioning of the test panels was added; b) the principle clause for methods A and B have been stated more precisely; c) the number of measurements has been added to methods C and D; d) the text has been editorially revised and the normative references have been updated. The EN 13523 series, Coil coated metals — Test methods, consists of the following parts: — Part 0: General introduction — Part 1: Film thickness — Part 2: Gloss — Part 3: Colour difference — Instrumental comparison — Part 4: Pencil hardness — Part 5: Resistance to rapid deformation (impact test) — Part 6: Adhesion after indentation (cupping test) — Part 7: Resistance to cracking on bending (T-bend test) — Part 8: Resistance to salt spray (fog) — Part 9: Resistance to water immersion — Part 10: Resistance to fluorescent UV radiation and water condensation — Part 11: Resistance to solvents (rubbing test) — Part 12: Resistance to scratching — Part 13: Resistance to accelerated ageing by the use of heat SIST EN 13523-1:2017
EN 13523-1:2017 (E) 4 — Part 14: Chalking (Helmen method) — Part 15: Metamerism — Part 16: Resistance to abrasion — Part 17: Adhesion of strippable films — Part 18: Resistance to staining — Part 19: Panel design and method of atmospheric exposure testing — Part 20: Foam adhesion — Part 21: Evaluation of outdoor exposed panels — Part 22: Colour difference — Visual comparison — Part 23: Resistance to humid atmospheres containing sulfur dioxide — Part 24: Resistance to blocking and pressure marking — Part 25: Resistance to humidity — Part 26: Resistance to condensation of water — Part 27: Resistance to humid poultice (Cataplasm test) — Part 29: Resistance to environmental soiling (Dirt pick-up and striping) According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 13523-1:2017
EN 13523-1:2017 (E) 5 1 Scope This part of the EN 13523 series specifies the procedures for determining the dry-film thickness of an organic coating on a metallic substrate (coil coating). Four appropriate methods are given in this European Standard: a) magnetic induction; b) eddy current; c) micrometer; d) optical. The methods are applicable only to products with smooth and flat substrates but the coating itself may be textured. In that case, for methods a) and b) the average of a series of readings will represent an average of the thickness of the organic coating, while method c) will give the maximum thickness and m
...
SLOVENSKI STANDARD
oSIST prEN 13523-1:2016
01-januar-2016
3UHYOHþHQHNRYLQHNLVHQDYLMDMR3UHVNXVQHPHWRGHGHO 'HEHOLQDSUHPD]D
Coil coated metals - Test methods - Part 1: Film thickness
Bandbeschichtete Metalle - Prüfverfahren - Teil 1: Schichtdicke
Tôles prélaquées - Méthodes d'essai - Partie 1 : Epaisseur du revêtement
Ta slovenski standard je istoveten z: prEN 13523-1
ICS:
17.040.20 Lastnosti površin Properties of surfaces
25.220.60 Organske prevleke Organic coatings
oSIST prEN 13523-1:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 13523-1:2016
---------------------- Page: 2 ----------------------
oSIST prEN 13523-1:2016
DRAFT
EUROPEAN STANDARD
prEN 13523-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2015
ICS 17.040.20; 25.220.60 Will supersede EN 13523-1:2009
English Version
Coil coated metals - Test methods - Part 1: Film thickness
Tôles prélaquées - Méthodes d'essai - Partie 1 : Bandbeschichtete Metalle - Prüfverfahren - Teil 1:
Epaisseur du revêtement Schichtdicke
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 139.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13523-1:2015 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 13523-1:2016
prEN 13523-1:2015 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 5
4.1 Method A: Measurement on a magnetic substrate – magnetic induction . 5
4.2 Method B: Measurement on a non-magnetic substrate – eddy current . 6
4.3 Method C: Measurement on all substrates – micrometre method . 6
4.4 Method D: Measurement on all substrates – optical method . 6
5 Apparatus and materials . 6
6 Sampling . 6
7 Test panels . 6
8 Procedure. 7
8.1 Calibration . 7
8.1.1 General . 7
8.1.2 Calibration standards . 7
8.2 Scale rating . 7
8.3 Measurement . 7
8.3.1 Ambient conditions . 7
8.3.2 Number of measurements . 7
8.3.3 Method A: Magnetic induction . 7
8.3.4 Method B: Eddy current . 8
8.3.5 Method C: Micrometre method . 8
8.3.6 Method D: Optical method . 8
9 Expression of results . 9
10 Accuracy . 9
11 Test report . 9
Bibliography . 10
2
---------------------- Page: 4 ----------------------
oSIST prEN 13523-1:2016
prEN 13523-1:2015 (E)
European foreword
This document (prEN 13523-1:2015) has been prepared by Technical Committee CEN/TC 139 “Paints
and varnishes”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 13523-1:2009.
The main changes are:
a) a reference to EN 13523-0 concerning conditioning of the test panels was added;
b) the principle clause for methods A and B have been stated more precisely;
c) the number of measurements has been added to methods C and D;
d) the text has been editorially revised and the normative references have been updated.
The EN 13523 series, Coil coated metals — Test methods, consists of the following parts:
— Part 0: General introduction;
— Part 1: Film thickness;
— Part 2: Gloss;
— Part 3: Colour difference — Instrumental comparison;
— Part 4: Pencil hardness;
— Part 5: Resistance to rapid deformation (impact test);
— Part 6: Adhesion after indentation (cupping test);
— Part 7: Resistance to cracking on bending (T-bend test);
— Part 8: Resistance to salt spray (fog);
— Part 9: Resistance to water immersion;
— Part 10: Resistance to fluorescent UV radiation and water condensation;
— Part 11: Resistance to solvents (rubbing test);
— Part 12: Resistance to scratching;
— Part 13: Resistance to accelerated ageing by the use of heat;
— Part 14: Chalking (Helmen method);
— Part 15: Metamerism;
3
---------------------- Page: 5 ----------------------
oSIST prEN 13523-1:2016
prEN 13523-1:2015 (E)
— Part 16: Resistance to abrasion;
— Part 17: Adhesion of strippable films;
— Part 18: Resistance to staining;
— Part 19: Panel design and method of atmospheric exposure testing;
— Part 20: Foam adhesion;
— Part 21: Evaluation of outdoor exposed panels;
— Part 22: Colour difference — Visual comparison;
— Part 23: Resistance to humid atmospheres containing sulfur dioxide;
— Part 24: Resistance to blocking and pressure marking;
— Part 25: Resistance to humidity;
— Part 26: Resistance to condensation of water;
— Part 27: Resistance to humid poultice (Cataplasm test);
— Part 29: Resistance to environmental soiling (Dirt pick-up and striping).
4
---------------------- Page: 6 ----------------------
oSIST prEN 13523-1:2016
prEN 13523-1:2015 (E)
1 Scope
This part of the EN 13523 series specifies the procedures for determining the dry-film thickness of an
organic coating on a metallic substrate (coil coating).
Four appropriate methods are given in this European Standard:
a) magnetic induction;
b) eddy current;
c) micrometer;
d) optical.
The methods are applicable only to products with smooth and flat substrates but the coating itself may
be textured. In that case, for methods a) and b) the average of a series of readings will represent an
average of the thickness of the organic coating, while method c) will give the maximum thickness and
method d) can provide the minimum, maximum and average thickness.
Non-destructive continuous-web methods on measurement of dry-film thickness (see EN ISO 2808) are
not dealt with.
2 Norm
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.