SIST EN ISO 3834-3:2006

SLOVENSKI STANDARD
SIST EN ISO 3834-3:2006
01-marec-2006
1DGRPHãþD
SIST EN 729-3:1995
Zahteve za kakovost pri talilnem varjenju kovinskih materialov – 3. del: Standardne
zahteve za kakovost (ISO 3834-3:2005)
Quality requirements for fusion welding of metallic materials - Part 3: Standard quality
requirements (ISO 3834-3:2005)
Qualitätsanforderungen für das Schmelzschweißen von metallischen Werkstoffen - Teil
3: Standard-Qualitätsanforderungen (ISO 3834-3:2005)
Exigences de qualité en soudage par fusion des matériaux métalliques - Partie 3:
Exigences de qualité normale (ISO 3834-3:2005)
Ta slovenski standard je istoveten z: EN ISO 3834-3:2005
ICS:
03.120.99 Drugi standardi v zvezi s Other standards related to
kakovostjo quality
25.160.10 Varilni postopki in varjenje Welding processes
SIST EN ISO 3834-3:2006 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 3834-3:2006

---------------------- Page: 2 ----------------------

SIST EN ISO 3834-3:2006


EUROPEAN STANDARD EN ISO 3834-3

NORME EUROPÉENNE

EUROPÄISCHE NORM
December 2005
ICS 25.160.01 Supersedes EN 729-3:1994
English Version
Quality requirements for fusion welding of metallic materials -
Part 3: Standard quality requirements (ISO 3834-3:2005)
Exigences de qualité en soudage par fusion des matériaux Qualitätsanforderungen für das Schmelzschweißen von
métalliques - Partie 3: Exigences de qualité normale (ISO metallischen Werkstoffen - Teil 3: Standard-
3834-3:2005) Qualitätsanforderungen (ISO 3834-3:2005)
This European Standard was approved by CEN on 28 October 2005.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.

CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.






EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3834-3:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 3834-3:2006

EN ISO 3834-3:2005 (E)





Foreword


This document (EN ISO 3834-3:2005) has been prepared by Technical Committee ISO/TC 44
"Welding and allied processes" in collaboration with Technical Committee CEN/TC 121
"Welding", the secretariat of which is held by DIN.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by June 2006, and conflicting national
standards shall be withdrawn at the latest by June 2006.

This document supersedes EN 729-3:1994.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.


Endorsement notice

The text of ISO 3834-3:2005 has been approved by CEN as EN ISO 3834-3:2005 without any
modifications.

2

---------------------- Page: 4 ----------------------

SIST EN ISO 3834-3:2006

INTERNATIONAL ISO
STANDARD 3834-3
Second edition
2005-12-15


Quality requirements for fusion welding
of metallic materials —
Part 3:
Standard quality requirements
Exigences de qualité en soudage par fusion des matériaux
métalliques —
Partie 3: Exigences de qualité normale





Reference number
ISO 3834-3:2005(E)
©
ISO 2005

---------------------- Page: 5 ----------------------

SIST EN ISO 3834-3:2006
ISO 3834-3:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2005 – All rights reserved

---------------------- Page: 6 ----------------------

SIST EN ISO 3834-3:2006
ISO 3834-3:2005(E)
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 1
4 Use of this part of ISO 3834 . 1
5 Review of requirements and technical review.2
6 Sub-contracting . 3
7 Welding personnel. 3
8 Inspection and testing personnel . 4
9 Equipment. 4
10 Welding and related activities . 5
11 Storage and handling welding consumables . 6
12 Storage of parent materials . 6
13 Post-weld heat treatment . 6
14 Inspection and testing. 6
15 Non-conformance and corrective actions. 8
16 Calibration and validation of measuring, inspection and testing equipment . 8
17 Identification and traceability. 8
18 Quality records. 8

© ISO 2005 – All rights reserved iii

---------------------- Page: 7 ----------------------

SIST EN ISO 3834-3:2006
ISO 3834-3:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 3834-3 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee
SC 10, Unification of requirements in the field of metal welding.
This second edition cancels and replaces the first edition (ISO 3834-3:1994), which has been technically
revised.
ISO 3834 consists of the following parts, under the general title Quality requirements for fusion welding of
metallic materials:
⎯ Part 1: Criteria for the selection of the appropriate level of quality requirements
⎯ Part 2: Comprehensive quality requirements
⎯ Part 3: Standard quality requirements
⎯ Part 4: Elementary quality requirements
⎯ Part 5: Documents with which it is necessary to conform to claim conformity to the quality requirements of
ISO 3834-2, ISO 3834-3 or ISO 3834-4
NOTE A Technical Report ISO/TR 3834-6, Quality requirements for fusion welding of metallic materials — Part 6:
Guidance on implementing ISO 3834 is being prepared.
Requests for official interpretations of any aspect of this part of ISO 3834 should be directed to the Secretariat
of ISO/TC 44/SC 10 via your national standards body, a complete listing which can be found at
http://www.iso.org.

iv © ISO 2005 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 3834-3:2006
INTERNATIONAL STANDARD ISO 3834-3:2005(E)

Quality requirements for fusion welding of metallic materials —
Part 3:
Standard quality requirements
1 Scope
This part of ISO 3834 defines standard quality requirements for fusion welding of metallic materials both in
workshops and at field installation sites.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 3834-1, Quality requirements for fusion welding of metallic materials — Part 1: Criteria for the selection of
the appropriate level of quality requirements
ISO 3834-5:2005, Quality requirements for fusion welding of metallic materials — Part 5: Documents with
which it is necessary to conform to claim conformity to the quality requirements of ISO 3834-2, ISO 3834-3 or
ISO 3834-4
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 3834-1 apply.
4 Use of this part of ISO 3834
For general information on the use of this part of ISO 3834, ISO 3834-1 shall be used.
In order to fulfil the quality requirements given in this part of ISO 3834, the conformity to relevant documents
given in ISO 3834-5 shall be verified.
In certain situations, e.g. where manufacturing is more suited to ISO 3834-4, or where particular operations,
such as heat treatment, are not undertaken, the requirements detailed in this part of ISO 3834 may be
selectively amended or deleted.
Otherwise, the requirements contained within this part of ISO 3834 shall be adopted in full.
© ISO 2005 – All rights reserved 1

---------------------- Page: 9 ----------------------

SIST EN ISO 3834-3:2006
ISO 3834-3:2005(E)
5 Review of requirements and technical review
5.1 General
The manufacturer shall review the contractual requirements and any other requirements, together with any
technical data provided by the purchaser or in-house data when the construction is designed by the
manufacturer. The manufacturer shall establish that all information necessary to carry out the manufacturing
operations is complete and available prior to the commencement of the work. The manufacturer shall affirm
its capability to meet all requirements and shall ensure adequate planning of all quality-related activities.
The review of requirements is carried out by the manufacturer to verify that the work content is within its
capability to perform, that sufficient resources are available to achieve delivery schedules and that
documentation is clear and unambiguous. The manufacturer shall ensure that any variations between the
contract and any previous quotation are identified and the purchaser notified of any programme, cost or
engineering changes that may result.
Items in 5.2 are typically considered at or before the time of the review of requirements. Items in 5.3 usually
form part of the technical review and are considered during the initial planning stage.
When a contract does not exist, e.g. items made for stock, the manufacturer is required to take into
consideration the requirements of 5.2 while carrying out the technical review (see 5.3).
5.2 Review of requirements
Aspects to be considered shall include the following:
a) the product standard to be used, together with any supplementary requirements;
b) statutory and regulatory requirements;
c) any additional requirement determined by the manufacturer;
d) the capability of the manufacturer to meet the prescribed requirements.
5.3 Technical review
Technical requirements to be considered shall include the following:
a) parent material(s) specification and welded joint properties;
b) quality and acceptance requirements for welds;
c)
...