SIST EN 13985:2003

SLOVENSKI STANDARD
SIST EN 13985:2003
01-november-2003
Obdelovalni stroji - Varnost - Škarje
Machine tools - Safety - Guillotine shears
Werkzeugmaschinen - Sicherheit - Tafelscheren
Machines-outils - Sécurité - Cisailles guillotines
Ta slovenski standard je istoveten z: EN 13985:2003
ICS:
25.120.10 Kovaški stroji. Stiskalnice. Forging equipment. Presses.
Škarje Shears
SIST EN 13985:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 13985:2003

---------------------- Page: 2 ----------------------

SIST EN 13985:2003
EUROPEAN STANDARD
EN 13985
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2003
ICS 25.120.10
English version
Machine tools - Safety - Guillotine shears
Machines-outils - Sécurité - Cisailles guillotines Werkzeugmaschinen - Sicherheit - Tafelscheren
This European Standard was approved by CEN on 14 November 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13985:2003 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 13985:2003
EN 13985:2003 (E)
Contents
page
Foreword.3
1 Scope .4
2 Normative references .4
3 Terms, definitions and abbreviations .6
3.1 Terms and definitions.6
3.2 Abbreviations .8
4 List of significant hazards.8
5 Safety requirements and/or protective measures .12
5.1 General.12
5.2 Basic design considerations .13
5.3 Mechanical hazards in the blade and associated area .16
5.4 The control and monitoring system.23
5.5 Tool-setting, trial strokes, maintenance and lubrication.25
5.6 Mechanical hazards - Other .26
5.7 Slips, trips and falls .26
5.8 Protection against other hazards.26
6 Verification of the safety requirements and/or protective measures.31
7 Information for use .36
7.1 Marking .36
7.2 Instruction handbook .37
Annex A (normative)  Calculation of minimum safety distances .39
Annex B (normative)  The response time of the redundant hydraulic/pneumatic systems.41
Annex C (informative)  Example of a hydraulic control circuit for a guillotine shear provided with fixed
guards or light curtain.42
Annex D (normative)  Conditions for noise measurement of guillotine shears .44
Annex ZA (informative)  Relationship of this standard with EC Directives.45
Bibliography .46
2

---------------------- Page: 4 ----------------------

SIST EN 13985:2003
EN 13985:2003 (E)
Foreword
This document (EN 13985:2003) has been prepared by Technical Committee CEN/TC 143 ”Machine tools -
Safety“, the secretariat of which is held by SNV.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by July 2003, and conflicting national standards shall be withdrawn at the latest by
July 2003.
This document has been prepared under a mandate given to CEN by the European Commission and the European
Free Trade Association, and supports essential requirements of EC Directive(s).
For relationship with EC directive(s), see informative Annex ZA, which is an integral part of this document.
Organisation contributing to the preparation of this European Standard include the European Manufacturer
Association CECIMO.
NOTE  The safety requirements related to the use of PES or PPS will be dealt with at its next revision.
The European Standards produced by CEN/TC 143 are particular to machine tools and complement the relevant A
and B standards on the subject of general safety (see introduction of EN 292-1:1991 for a description of A, B and C
standards).
Annexes A, B and D are normative. Annex C is informative.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal,
Slovakia, Spain, Sweden, Switzerland and the United Kingdom.
0 Introduction
This European Standard has been prepared to be a harmonised standard to provide one means of conforming to
the essential safety requirements of the “Machinery“ Directive and associated EFTA Regulations. It is a C-type
standard as described in EN 1070:1998.
The machinery concerned and the extent to which hazards, hazardous situations and events are covered are
indicated in the scope of this standard. When provisions of this C type standard are different from those which are
stated in A or B standards, the provision of this C type standard take precedence over the provisions of the other
standards for machines that have been designed and built according to the provisions of this C type standard.
Complementary guidance is given in the A and B standards to which reference is made in the text (see clause 2).
The figures are intended to be examples only and not to give the only interpretation of the text.
The requirements of this European Standard concern designers, manufacturers, suppliers and importers of
machines described in the scope.
This standard also includes information to be provided by the manufacturer to the user.
3

---------------------- Page: 5 ----------------------

SIST EN 13985:2003
EN 13985:2003 (E)
1 Scope
1.1 This European Standard specifies technical safety requirements and measures to be adopted by persons
undertaking the design as defined in 3.11 of EN 292-1:1991, manufacture and supply of guillotine shears which are
intended to work cold metal or material partly of cold metal as defined in 3.1.7 and hereafter referred as machines.
1.2 This standard also covers guillotine shears whose primary intended use is to work cold metal, which are to
be used in the same way to work other sheet materials (e.g. cardboard, plastic, rubber, leather).
1.3 The requirements in this standard take account of intended use, as defined in 3.12 of EN 292-1:1991. This
standard presumes access to the guillotine shear from all directions, deals with the hazards described in clause 4,
and specifies the safety requirements and/or protective measures for both the operator and other exposed persons.
1.4 This standard also applies to ancillary devices which are an integral part of the guillotine shear. This
standard also applies to machines which are integrated into an automatic production line where the hazards and
risk arising are comparable to those of machines working separately.
1.5 This standard includes guillotine shears in which energy is imparted to the blade by a number of means. e.g.:
a) mechanically driven from a motor through a friction clutch;
b) through a direct drive motor and brake;
c) through hydraulic pressure;
d) through pneumatic pressure.
1.6 This standard does not cover machines whose principal designed purpose is:
a) cutting in other than a straight line (e.g. at nibbling machines);
b) cutting by continuous action at crocodile shears (see 3.4).
1.7 This standard does not cover the safety requirements related to the use of PES or PPS. They will be dealt with
at its next revision.
1.8 This standard is not applicable to machines which are manufactured before the date of publication of this
document by CEN.
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For
dated references, subsequent amendments to or revisions of any of these publications apply to this European
Standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the
publication referred to applies (including amendments).
EN 292-1:1991, Safety of machinery – Basic concepts, general principles for design – Part 1: Basic terminology,
methodology.
EN 292-2:1991, Safety of machinery – Basic concepts, general principles for design – Part 2: Technical principles
and specifications.
EN 294:1992, Safety of machinery – Safety distance to prevent danger zones being reached by the upper limbs.
EN 418:1992, Safety of machinery – Emergency stop equipment, functional aspects – Principles for design.
4

---------------------- Page: 6 ----------------------

SIST EN 13985:2003
EN 13985:2003 (E)
EN 563, Safety of machinery – Temperatures of touchable surfaces – Ergonomics data to establish temperature
limit values for hot surfaces.
EN 614-1, Safety of machinery – Ergonomic design principles – Part 1: Terminology and general principles.
EN 894-2:1997, Safety of machinery – Ergonomic requirements for the design of displays and control actuators –
Part 2: Displays.
EN 894-3:2000, Safety of machinery – Ergonomic requirements for the design of displays and control actuators –
Part 3: Control actuators.
EN 953:1997, Safety of machinery – Guards – General requirements for the design and construction of fixed and
movable guards.
EN 954-1:1996, Safety of machinery – Safety related parts of control systems – Part 1: General principles for
design.
EN 982:1996, Safety of machinery – Safety requirements for fluid power systems and their components –
Hydraulics.
EN 983:1996, Safety of machinery – Safety requirements for fluid power systems and their components –
Pneumatics.
EN 999:1998, Safety of machinery – The positioning of protective equipment in respect to approach speeds of
parts of the human body.
prEN 1005-2, Safety of machinery – Human physical performance – Part 2: Manual handling of machinery and
component parts of machinery.
EN 1037:1995, Safety of machinery – Prevention of unexpected started up.
EN 1050:1996, Safety of machinery – Principles for risk assessment.
EN 1070:1998, Safety of machinery –Terminology.
EN 1088:1995, Safety of machinery – Interlocking devices associated with guards – Principles for design and
selection.
EN 1837:1999, Safety of machinery – Integral lighting of machines.
EN ISO 3746:1995, Acoustics – Determination of sound power levels of noise sources using sound pressure –
Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:1995).
EN ISO 4871:1996, Acoustics – Declaration and verification of noise emission values of machinery and equipment
(ISO 4871:1996).
EN ISO 11202:1995, Acoustics – Noise emitted by machinery and equipment – Measurement of emissions of
sound pressure levels at the work station and other specified positions – Survey method in situ (ISO 11202:1995).
EN ISO 11688-1:1998, Acoustics – Recommended practice for the design of low-noise machinery and equipment –
Part 1: Planning (ISO/TR 11688-1:1995).
EN ISO 11688-2:2000, Acoustics – Recommended practice for the design of low-noise machinery and equipment –
Part 2: Introduction to the physics of low-noise design (ISO/TR 11688-2:1998).
EN ISO 14122-1, Safety of machinery – Permanent means of access to machinery – Part 1: Choice of fixed means
of access between two levels (ISO 14122-1:2001).
EN ISO 14122-2, Safety of machinery – Permanent means of access to machinery – Part 2: Working platforms and
walkways (ISO 14122-2:2001).
5

---------------------- Page: 7 ----------------------

SIST EN 13985:2003
EN 13985:2003 (E)
EN ISO 14122-3, Safety of machinery – Permanent means of access to machinery – Part 3: Stairs, stepladders
and guard-rails (ISO 14122-3:2001).
prEN ISO 14122-4, Safety of machinery – Permanent means of access to machines and industrial plants - Part 4:
Fixed ladders (ISO/FDIS 14122-4:1999).
EN 60204-1:1997, Safety of machinery – Electrical equipment of machines – Part 1: General requirements
(IEC 60204-1:1997).
EN 60529, Degrees of protection provided by enclosures (IP code) (IEC 60529:1989).
EN 60825-1, Safety of laser products – Part 1: Equipment classification, requirements and user's guide (IEC
60825-1:1993).
EN 61310-2:1995, Safety of machinery – Indication, marking and actuation – Part 2: Requirements for marking
(IEC 61310-2:1995).
EN 61496-1:1997, Safety of machinery – Electro-sensitive protective equipment – Part 1: General requirements
and tests (IEC 61496-1:1997).
prEN 61496-2:1997, Safety of machinery – Electrosensitive protective equipment – Part 2: Particular requirements
for equipment using active optoelectronic protective devices (IEC 61469-2).
3 Terms, definitions and abbreviations
3.1 Terms and definitions
For the purposes of this European Standard, the terms and definitions given in EN 1070:1998 and the following
definitions apply. Further definitions are provided in relevant A and B standards and in annex A of EN 292-
2:1991/A1:1995.
3.1.1
ancillary device
device intended for use with the guillotine shear and integrated with it (e.g. devices for lubrication, feed, ejection)
3.1.2
beam
main reciprocating guillotine shear member holding the top blade. The top blade can be guided either by direct
slide (vertically up and down) or swinging beam
3.1.3
clamp
part of the machine which holds the sheet material in position on the work table during the cutting stroke. Also
called hold-down or jack
3.1.4
crocodile shears
shears having a shearing action like that of scissors. Power is applied in an angular direction around the pivot and
the action of the blades is guided only by the pivot
3.1.5
cycle (operating cycle)
movement completed by the moving parts from the cycle start position (normally the top dead centre) to the bottom
dead centre and back to the cycle stop position (normally the top dead centre). The operating cycle includes all
operations carried out during this movement
6

---------------------- Page: 8 ----------------------

SIST EN 13985:2003
EN 13985:2003 (E)
3.1.6
dead centres
points at which the moving blade, during its travel, is
a) either at the end of the chosen closing stroke, known as the bottom dead centre (BDC),
b) or at the end of the chosen opening stroke, known as the top dead centre (TDC)
3.1.7
guillotine shears
machine, sometimes known simply as a guillotine or shears, consisting of side frames bridged by a work table to
which is fixed a bottom blade and a movable upper beam to which is fixed a top blade(s). The blades may also be
of fixed or variable angle (i.e. the angular relationship between the top and bottom blades)
Figure 1 — Guillotine shear
3.1.8
inching device; limited movement control device
control device, the actuation of which permits only a limited amount of travel of a machine element, thus minimising
risk as much as possible; further movement is precluded until there is subsequent and separate actuation of the
control (see 3.23.8 of EN 292-1:1991)
3.1.9
monitoring
safety function which ensures that a protective measure is initiated if the ability of a component or an element to
perform its function is diminished, or if the process conditions are changed in such a way that hazards are
generated (see 3.7.6 of EN 292-2:1991)
3.1.10
muting
temporary automatic suspension of a safety function(s) by safety related parts of the control system (see 3.7 of
EN 954-1:1996)
7

---------------------- Page: 9 ----------------------

SIST EN 13985:2003
EN 13985:2003 (E)
3.1.11
overall system stopping performance; overall response time
time occurring from actuating the protective device to the cessation of hazardous motion, or to the machine
assuming a safe condition
3.1.12
redundancy
application of more than one device or system, or part of a device or a system, with the objective of ensuring that,
in the event of one failing to perform its function, another is available to perform that function (see 3.44 of
EN 60204-1:1997 and 3.7.5 of EN 292-2:1991)
3.2 Abbreviations
3.2.1 M Monitoring (see 3.1.9)
3.2.2 R Redundancy (see 3.1.12)
3.2.3 S Single channel
3.2.4 BDC Bottom dead centre (see 3.1.6)
3.2.5 TDC Top dead centre (see 3.1.6)
3.2.6 PES Programmable electronic systems
3.2.7 PPS Programmable pneumatic systems
3.2.8 AOPD Active opto-electronic protective devices
3.2.9 ESPE Electro-sensitive protective equipment
4 List of significant hazards
4.1 The list of hazards contained in Table 1 is the result of a hazard identification, their associated danger zones
and reference to protective measures for guillotine shears covered by the scope of this standard. The safety
requirements and/or protective measures and information for use contained in clauses 5 and 7 are based on a risk
assessment and deal with the identified hazards by either eliminating them or reducing the effects of the risks they
generate.
4.2 The risk assessment assumes foreseeable access from all directions, as well as unexpected and unintended
strokes or gravity falls. Risks to both the operators and other persons who can have access to the danger zones
are identified, taking into account hazards which can occur under various conditions of intended use (e.g.
commissioning, setting, production, maintenance, repair, decommissioning, dismantling - see also 3.11 of
EN 292-1:1991) during the life of the machine. The assessment includes an analysis of the effect of failure in the
control system.
4.3 The user of this standard (i.e. the designer, manufacturer, supplier) shall check that the list of significant
hazards in Table 1 is complete for the machine under consideration. If the user determines that there are additional
hazards then he shall analyse and evaluate the risks associated with these hazards in accordance with EN 1050
with particular attention to the intended use of the machine (e.g. commissioning, setting, production, maintenance,
repair, decommissioning, dismantling - see also 3.11 of EN 292-1:1991), and its reasonably foreseeable misuse.
8

---------------------- Page: 10 ----------------------

SIST EN 13985:2003
EN 13985:2003 (E)
Table 1 — Significant hazards, danger zones, protective measures
No. Hazards Danger zone Relevant Relevant Protective
clauses in clauses in measures:
EN 292- EN 292- relevant
2/A1:1995 1:1991 clauses in this
standard
1.0 Mechanical hazards 1.3 4.2
Generated by machine parts (except 1.3.6)
or work-pieces Blades and associated area:
Generated by accumulation of – between the moving blade 1.5.3, 1.6.1, 4.2
energy inside the machinery and the work-piece 1.6.3
caused, for example, by: – between the moving blade
– elastic elements (springs) and the fixed blade 5.2.6
– liquids and gases under – between moving and fixed 5.5.2
pressure parts of guillotine shear 5.3
– between the table and work- 5.5
piece
– between the clamps and
work-piece or table
– between fixtures/positioning
devices and work-piece
– at power operated gauges
– moving work-pieces,
1.1 Crushing hazard – ejection or falling of work- 1.3
pieces at the rear of guillotine (except 1.3.6)
shear,
1.2 Shearing hazard – rear moving sheet supports, 1.4 (except 4.2.1
– rear sheet conveyor, 1.4.2.3),
– sheet stacking unit 1.5.14
1.3 Cutting of severing hazard From the hazardous event of
falling objects
1.4 Entanglement hazard
1.5 Drawing-in or trapping hazard
1.6 Impact hazard Moving parts of electrical, 1.3 4.2.1 5.6
hydraulic and pneumatic
equipment
Motor and drive machinery
– moving flywheels, belts,
pulleys and other motor driven
parts
Mechanical handling device
1.9 High pressure fluid injection Hydraulic systems 1.3.2 4.2.1 5.8.3
or ejection hazard
(continued)
9

---------------------- Page: 11 ----------------------

SIST EN 13985:2003
EN 13985:2003 (E)
Table 1 (continued)
No. Hazards Danger zone Relevant Relevant Protective
clauses in clauses in measures:
EN 292- EN 292- relevant
2/A1:1995 1:1991 clauses in this
standard
2 Electrical hazards due to
2.1 Contact of persons with live Electrical equipment 1.5.1, 1.6.3 4.3 5.8.3
parts (direct contact)
2.2 Contact of persons with parts Electrical equipment 1.5.1 4.3
which have become live
under faulty conditions
(indirect contact)
3 Thermal hazards
3.1 Thermal hazards resulting in Parts of the hydraulic system 1.5.5, 1.5.6, 4.4 5.2.1.5, 5.8.2
burns and scalds, by a 1.5.7
possible contact of persons
4 Hazards generated by noise
4.1 Other physiological disorders Falling of work-pieces at the 1.5.8 4.5 5.8.5, 7.2.2 g)
(e.g. loss of balance, loss of rear of guillotine shear
awareness) hearing losses
(deafness)
6 Hazards generated by
radiation
6.5 Lasers Any area at the guillotine shear 1.5.12 4.7 5.8.6
where there is a risk due to
laser beam.
7.0 Hazards generated by 5.8.7
materials and substances
processed or used by
machinery, for example:
7.1 Hazards from contact with or Toxic materials used in the 1.1.3, 1.5.13, 4.8 5.8.7.1
inhalation of harmful fluids, construction and intended use 1.6.5 5.8.7.2
gases, mists, fumes and of the guillotine shear 5.8.7.3
dusts
8.0 Hazards generated by
neglecting ergonomic
principles in machinery
design, as e.g. from:
8.1 Unhealthy postures or 1.1.2 d), 1.1.5, 4.9 5.8.8
excessive effort 1.6.2, 1.6.4
8.2 Inadequate consideration of 1.1.2 d), 2.2
hand-arm or foot-leg anatomy
8.4 Inadequate local lighting 1.1.4 5.8.8.3, 7.2.2d)
(continued)
10

---------------------- Page: 12 ----------------------

SIST EN 13985:2003
EN 13985:2003 (E)
Table 1 (continued)
No. Hazards Danger zone Relevant Relevant Protective
clauses in clauses in measures:
EN 292- EN 292- relevant
2/A1:1995 1:1991 clauses in this
standard
8.6 Human error, human 1.1.2 d), 1.2.2, 4.9 5.4.5.1, 5.4.3,
behaviour 1.2.5, 1.2.8, 5.4.6
1.5.4, 1.7
8.7 Inadequate design, location 1.2.2 5.4.3, 5.4.4,
or identification of manual 5.4.5, 5.8.8.2
controls
8.8 Inadequate design or location 1.7.1 5.8.8.2
of visual display units
10 Unexpected start-up,
unexpected overrun/ over
speed
10.1 Failure/disorder of the control 1.2.7, 1.6.3 5.2.1, 5.2.1.4,
system Blades and associated area: 5.2.1.7, 5.2.2,
5.4.1
10.2 Restoration of the energy – between the moving blade 1.2.6 5.4, 7.2.2 o)
supply after an interruption and the work-piece
– between the moving blade
and the fixed blade
– between the table and work-
piece
– between the clamps and
work-piece or table
– between fixtures/positioning
devices and work-piece
– safeguarding
– at power operated gauges
(continued)
11

---------------------- Page: 13 ----------------------

SIST EN 13985:2003
EN 13985:2003 (E)
Table 1 (concluded)
No. Hazards Danger zone Relevant Relevant Protective
clauses in clauses in measures:
EN 292- EN 292- relevant
2/A1:1995 1:1991 clauses in this
standard
10.3 External influences on – ejection or falling of work- 1.2.1, 1.5.11 5.4
electrical equipment pieces at the rear of guillotine
shear
– rear moving sheet supports,
10.4 Other external influences – rear sheet conveyor, 1.2.1
(gravity, wind etc.) – sheet stacking unit
10.5 Errors in the software 1.2.1 5.4.2
10.6 Errors made by the operator 1.1.2 d), 1.2.2, 4.9 7.2.2
(due to mismatch of machin- 1.2.5, 1.2.8,
ery with human character- 1.5.4, 1.7
istics and abilities, see 8.6)
13 Failure of the power supply see 10 1.2.6 5.2.1.12
14 Failure of the control circuit 1.2.1, 1.2.3, 5.2.1.4
1.2.4, 1.2.5,
1.2.7, 1.6.3
15 Errors of fitting
Blades 1.5.4 4.9 5.5.1, 5.5.4
16 Break-up during operation Mechanical, electrical, hydrau- 1.3.2 4.2.2 5.2.1, 5.2.2
lic, and pneumatic equipment
17 Falling or ejected objects or
Machine components 1.3.3 4.2.2 5.2.6, 5.3.13,
fluids Work-pieces and blades 5.6.4, 5.8.3
18 Loss of stability/ Floor area around the guillotine 1.3.1 4.2.2 5.8.4
overturning of machinery shear
19 Slip, trip and fall of persons All access and/or work at 1.5.15 4.2.3 5.7
(related to machinery)
heights
Floor area around the guillotine
shear
5 Safety requirements and/or protective measures
5.1 General
The guillotine shears covered by this standard range in size from small to large machines with a single operator or
several operators.
The methods or measures to be implemented to eliminate the significant hazards or reduce their associated risks
are detailed in this clause in the following manner:
 basic design considerations for major guillotine components or systems (see 5.2);
 safeguarding against mechanical hazards in the blade area under different modes of production (see 5.3);
 protection against hazards due to control system or control component failures (see 5.4);
 safeguarding against hazards which can occur during setting, trial strokes, maintenance and lubrication (see
5.5);
 safeguarding against other hazards (see 5.6 to 5.8).
12

---------------------- Page: 14 ----------------------

SIST EN 13985:2003
EN 13985:2003 (E)
In addition, the machine shall be designed according to the principles of EN 292 for hazards relevant but not
significant which are not dealt with by this standard.
5.2 Basic design considerations
5.2.1 Brakes and friction clutches
5.2.1.1 Fluid or air pressure shall not be used to apply a brake unless means are provided to ensure that, in
the event of loss of fluid or air pressure, the integrity of the brake is maintained and the clutch is disengaged.
Diaphragms shall not be used to apply a brake.
5.2.1.2 The designer shall ensure that:
a) the springs used for applying the brake or disengaging the clutch are of compression type and well tried
components;
b) multiple assemblies are used;
c) all the springs are closely uniform in dimension, quality and rating;
d) the means of loading the springs are such that, when adjusted, the spring anchorages can be locked to
prevent slackening back;
e) the arrangements for spring housing and guiding, and of guide pins, are such as to minimize binding;
f) the brake can function even if 50 % of the spring assembly has failed.
5.2.1.3 The arrangement provided for engagement and disengagement of the clutch and brake shall not affect
their safe function.
NOTE Combined clutch and brake units are recommended so as to reduce the possibility of the overlapping of their
engagement.
5.2.1.4 The clutch and brake shall be designed so that failure of components e.g. for power transmission or
screws shall not prevent the clutch to be disengaged and the brake to be applied.
5.2.1.5 Any heat generated which can cause a hazardous situation shall be dissipated.
5.2.1.6 Effective arrangements shall
...