SIST EN ISO 14329:2004

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Widerstandsschweißen - Zerstörende Prüfung von Schweißverbindungen - Brucharten und geometrische Messgrößen für Widerstandspunkt-, Rollennaht- und Buckelschweißungen (ISO 14329:2003)Soudage par résistance - Essais destructifs des soudures - Types de rupture et dimensions géométriques pour les assemblages soudés par résistance par points, a la molette et par bossages (ISO 14329:2003)Resistance welding - Destructive tests of welds - Failure types and geometric measurements for resistance spot, seam and projection welds (ISO 14329:2003)25.160.40Varjeni spoji in variWelded jointsICS:Ta slovenski standard je istoveten z:EN ISO 14329:2003SIST EN ISO 14329:2004en01-junij-2004SIST EN ISO 14329:2004SLOVENSKI
STANDARD



SIST EN ISO 14329:2004



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 14329July 2003ICS 25.160.40English versionResistance welding - Destructive tests of welds - Failure typesand geometric measurements for resistance spot, seam andprojection welds (ISO 14329:2003)Soudage par résistance - Essais destructifs des soudures -Types de rupture et dimensions géométriques pour lesassemblages soudés par résistance par points, à lamolette et par bossages (ISO 14329:2003)Widerstandsschweißen - Zerstörende Prüfung vonSchweißverbindungen - Brucharten und geometrischeMessgrößen für Widerstandspunkt-, Rollennaht- undBuckelschweißungen (ISO 14329:2003)This European Standard was approved by CEN on 5 June 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 14329:2003 ESIST EN ISO 14329:2004



EN ISO 14329:2003 (E)2CORRECTED
2003-09-24ForewordThis document (EN ISO 14329:2003) has been prepared by Technical Committee ISO/TC 44"Welding and allied processes" in collaboration with Technical Committee CEN/TC 121"Welding", the secretariat of which is held by DS.This European Standard shall be given the status of a national standard, either by publication ofan identical text or by endorsement, at the latest by January 2004, and conflicting nationalstandards shall be withdrawn at the latest by January 2004.According to the CEN/CENELEC Internal Regulations, the national standards organizations ofthe following countries are bound to implement this European Standard: Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland andthe United Kingdom.Endorsement noticeThe text of ISO 14329:2003 has been approved by CEN as EN ISO 14329:2003 without anymodifications.SIST EN ISO 14329:2004



Reference numberISO 14329:2003(E)© ISO 2003
INTERNATIONAL STANDARD ISO14329First edition2003-07-01Resistance welding — Destructive tests of welds — Failure types and geometric measurements for resistance spot, seam and projection welds Soudage par résistance — Essais destructifs des soudures — Types de rupture et dimensions géométriques pour les assemblages soudés par résistance par points, à la molette et par bossages
SIST EN ISO 14329:2004



ISO 14329:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2003 — All rights reserved
SIST EN ISO 14329:2004



ISO 14329:2003(E) © ISO 2003 — All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 14329 was prepared in collaboration with the International Institute of Welding which has been approved by the ISO Council as an international standardizing body in the field of welding.
SIST EN ISO 14329:2004



SIST EN ISO 14329:2004



INTERNATIONAL STANDARD ISO 14329:2003(E) © ISO 2003 — All rights reserved 1 Resistance welding — Destructive tests of welds — Failure types and geometric measurements for resistance spot, seam and projection welds 1 Scope This International Standard specifies the definitions of the geometric measurements and fracture types to be used in relation to the testing of resistance spot, projection and seam welds in which different loading configurations cause different stress distributions in the weld (see Figure 1). The aim of these definitions is to give a base for all other related standards.
Key 1 shear testing 3 peel testing 2 cross tension testing 4 torsion testing a Testing load Figure 1 — Schematic illustrations showing stress distribution depending on direction of the testing load SIST EN ISO 14329:2004



ISO 14329:2003(E) 2 © ISO 2003 — All rights reserved 2 Terms and definitions For the purposes of this document, the following terms and definitions apply. 2.1 Failure modes of specimens and components 2.1.1 interface failure fracture through the weld nugget between the sheets at the place of the interface See Figure 2. 2.1.2 partia
...