SIST EN ISO 8099:2001

SLOVENSKI STANDARD
SIST EN ISO 8099:2001
01-junij-2001
1DGRPHãþD
SIST EN 24567:2000
0DODSORYLOD6LVWHPL]D]DGUåHYDQMHVWUDQLãþQLKRGSODN,62
Small craft - Toilet waste retention systems (ISO 8099:2000)
Kleine Wasserfahrzeuge - Toiletten-Abfall-Sammel-Anlagen (ISO 8099:2000)
Petits navires - Systemes de rétention des déchets des installations sanitaires (toilettes)
(ISO 8099:2000)
Ta slovenski standard je istoveten z: EN ISO 8099:2000
ICS:
47.080 ýROQL Small craft
SIST EN ISO 8099:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 8099:2001

---------------------- Page: 2 ----------------------

SIST EN ISO 8099:2001
EUROPEAN STANDARD
EN ISO 8099
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2000
ICS 47.080
English version
Small craft - Toilet waste retention systems (ISO 8099:2000)
Petits navires - Systèmes de rétention des déchets des Kleine Wasserfahrzeuge - Toiletten-Abfall-Sammel-
installations sanitaires (toilettes) (ISO 8099:2000) Anlagen (ISO 8099:2000)
This European Standard was approved by CEN on 10 December 2000.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2000 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8099:2000 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 8099:2001
Page 2
EN ISO 8099:2000
CORRECTED 2001-04-04
Foreword
The text of the International Standard ISO 8099:2000 has been prepared by Technical
Committee ISO/TC 188 "Small craft", the secretariat of which is held by CMC.
This European Standard shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by June 2001, and conflicting national
standards shall be withdrawn at the latest by June 2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,
Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United
Kingdom.
Endorsement notice
The text of the International Standard ISO 8099:2000 was approved by CEN as a European
Standard without any modification.
NOTE: Normative references to International Standards are listed in annex ZA (normative).

---------------------- Page: 4 ----------------------

SIST EN ISO 8099:2001
Page 3
EN ISO 8099:2000
Annex ZA (normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions
of any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications,
indicated by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 9093-1 1994 Small craft - Seacocks and through- EN ISO 9093-1 1997
hull fittings - Part 1: Metallic
ISO 10133 2000 Small craft - Electrical systems - EN ISO 10133 2000
Extra low-voltage d.c. installations
ISO 13297 2000 Small craft - Electrical systems - EN ISO 13297 2000
Alternating current installations

---------------------- Page: 5 ----------------------

SIST EN ISO 8099:2001

---------------------- Page: 6 ----------------------

SIST EN ISO 8099:2001
INTERNATIONAL ISO
STANDARD 8099
Second edition
2000-12-15
Small craft — Toilet waste retention
systems
Petits navires — Systèmes de rétention des déchets des installations
sanitaires (toilettes)
Reference number
ISO 8099:2000(E)
©
ISO 2000

---------------------- Page: 7 ----------------------

SIST EN ISO 8099:2001
ISO 8099:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 8099:2001
ISO 8099:2000(E)
Contents Page
Foreword.iv
1 Scope .1
2 Normative reference .1
3 Terms and definitions .1
4 General requirements.2
5 Materials .2
6 Design and installation .2
7 Requirements for fixed holding tanks .5
8 Requirements for portable holding tanks .5
9 Test for fixed holding tanks.5
10 Identification.5
11 Pump-out deck fitting.6
12 Information for owner's manual .6
Annex A (normative) Nominal design of pump-out fitting.7
Annex B (informative) Typical installations for toilet retention systems .9
© ISO 2000 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 8099:2001
ISO 8099:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 8099 was prepared by Technical Committee ISO/TC 188, Small craft.
This second edition cancels and replaces the first edition (ISO 8099:1985), of which it constitutes a technical
revision.
Annex A forms a normative part of this International Standard. Annex B is for information only.
iv © ISO 2000 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 8099:2001
INTERNATIONAL STANDARD ISO 8099:2000(E)
Small craft — Toilet waste retention systems
1 Scope
This International Standard specifies requirements for the design, construction, and installation of systems for
temporary retention of sewage for subsequent disposal. It applies to small craft of hull length up to 24 m.
2 Normative reference
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of IEC and ISO
maintain registers of currently valid International Standards.
ISO 228-1:1994, Pipe threads where pressure-tight joints are not made on the threads — Part 1: Dimensions,
tolerances and designation.
1�
ISO 9093-1:1994 , Small craft — Seacocks and through-hull fittings — Part 1: Metallic.
ISO 10133:2000, Small craft — Electrical systems — Extra-low-voltage d.c. installations.
ISO 13297:2000, Small craft — Electrical systems — Alternating current installations.
3 Terms and definitions
For the purposes of this International Standard, the following terms and definitions apply.
3.1
retention system
interconnected sanitation equipment including hoses, pipes, holding tank and fittings designed for use on board
small craft to receive, retain, vent and dispose of sewage
3.2
sewage
human body waste
...