SIST EN 61158-3-3:2015

SLOVENSKI STANDARD
SIST EN 61158-3-3:2015
01-marec-2015
1DGRPHãþD
SIST EN 61158-3-3:2008
Industrijska komunikacijska omrežja - Specifikacije za procesna vodila - 3-3. del:
Specifikacija protokola na ravni podatkovnih povezav - Elementi tipa 3 (IEC 61158-
3-3:2014)
Industrial communication networks - Fieldbus specifications - Part 3-3: Data-link layer
service definition - Type 3 elements (IEC 61158-3-3:2014)
Industrielle Kommunikationsnetze - Feldbusse - Teil 3-3: Dienstfestlegungen des Data
Link Layer (Sicherungsschicht) - Typ 3-Elemente (IEC 61158-3-3:2014)
Réseaux de communication industriels - Spécifications des bus de terrain - Partie 3-3:
Définition des services de la couche liaison de données - Éléments de type 3 (CEI 61158
-3-3:2014)
Ta slovenski standard je istoveten z: EN 61158-3-3:2014
ICS:
25.040.40 Merjenje in krmiljenje Industrial process
industrijskih postopkov measurement and control
35.100.20 Podatkovni povezovalni sloj Data link layer
35.110 Omreževanje Networking
SIST EN 61158-3-3:2015 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61158-3-3:2015

---------------------- Page: 2 ----------------------

SIST EN 61158-3-3:2015


EUROPEAN STANDARD EN 61158-3-3

NORME EUROPÉENNE

EUROPÄISCHE NORM
October 2014
ICS 25.040.40; 35.100.20; 35.110 Supersedes EN 61158-3-3:2008
English Version
Industrial communication networks - Fieldbus specifications -
Part 3-3: Data-link layer service definition - Type 3 elements
(IEC 61158-3-3:2014)
Réseaux de communication industriels - Spécifications des Industrielle Kommunikationsnetze - Feldbusse - Teil 3-3:
bus de terrain - Partie 3-3: Définition des services de la Dienstfestlegungen des Data Link Layer
couche liaison de données - Éléments de type 3 (Sicherungsschicht) - Typ 3-Elemente
(CEI 61158-3-3:2014) (IEC 61158-3-3:2014)
This European Standard was approved by CENELEC on 2014-09-17. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 61158-3-3:2014 E

---------------------- Page: 3 ----------------------

SIST EN 61158-3-3:2015
EN 61158-3-3:2014 - 2 -
Foreword
The text of document 65C/759/FDIS, future edition 2 of IEC 61158-3-3, prepared by SC 65C
"Industrial networks" of IEC/TC 65 "Industrial-process measurement, control and automation" was
submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61158-3-3:2014.
The following dates are fixed:
(dop) 2015-06-17
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
(dow) 2017-09-17
• latest date by which the national standards conflicting with
the document have to be withdrawn

This document supersedes EN 61158-3-3:2008.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association.
Endorsement notice
The text of the International Standard IEC 61158-3-3:2014 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 61158-2 NOTE Harmonized as EN 61158-2.
IEC 61158-4-3 NOTE Harmonized as EN 61158-4-3.
IEC 61158-5-3 NOTE Harmonized as EN 61158-5-3.
IEC 61158-6-3 NOTE Harmonized as EN 61158-6-3.

---------------------- Page: 4 ----------------------

SIST EN 61158-3-3:2015
- 3 - EN 61158-3-3:2014
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is
available here: www.cenelec.eu.

Publication Year Title EN/HD Year
IEC 61158-1 -  Industrial communication networks - EN 61158-1 -
Fieldbus specifications -
Part 1: Overview and guidance for the
IEC 61158 and IEC 61784 series
ISO/IEC 7498-1 -  Information technology - Open Systems - -
Interconnection - Basic Reference Model:
The Basic Model
ISO/IEC 7498-3 -  Information technology - Open Systems - -
Interconnection - Basic Reference Model:
Naming and addressing
ISO/IEC 10731 - Information technology - Open Systems - -
Interconnection - Basic Reference Model -
Conventions for the definition of OSI
services

---------------------- Page: 5 ----------------------

SIST EN 61158-3-3:2015

---------------------- Page: 6 ----------------------

SIST EN 61158-3-3:2015



IEC 61158-3-3

®


Edition 2.0 2014-08




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Industrial communication networks – Fieldbus specifications –

Part 3-3: Data-link layer service definition – Type 3 elements




Réseaux de communication industriels – Spécifications des bus de terrain –

Partie 3-3: Définition des services de la couche liaison de données – Éléments

de type 3














INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX XB


ICS 25.040.40; 35.100.20; 35.110 ISBN 978-2-8322-1701-6



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 61158-3-3:2015
– 2 – IEC 61158-3-3:2014 © IEC 2014
CONTENTS
FOREWORD . 5
INTRODUCTION . 7
1 Scope . 8
1.1 General . 8
1.2 Specifications . 8
1.3 Conformance . 9
2 Normative references . 9
3 Terms, definitions, symbols, abbreviations and conventions . 9
3.1 Reference model terms and definitions . 9
3.2 Service convention terms and definitions . 11
3.3 Common data-link service terms and definitions . 12
3.4 Additional Type 3 data-link specific definitions. 13
3.5 Common symbols and abbreviations . 15
3.6 Additional Type 3 symbols and abbreviations . 16
3.7 Common conventions . 18
3.8 Additional Type 3 conventions . 19
4 Connectionless-mode data-link service . 20
4.1 General . 20
4.2 Model of the connectionless-mode data-link service . 20
4.3 Sequence of primitives . 22
4.4 Detailed description of DL services. 25
5 DL-management Service . 44
5.1 General . 44
5.2 Facilities of the DLMS . 44
5.3 Services of the DL-management . 45
5.4 Overview of interactions . 46
5.5 Detailed specification of services and interactions . 48
Bibliography . 68

Figure 1 – Relationships of DLSAPs, DLSAP-addresses and group DL-addresses . 12
Figure 2 – SDA service . 23
Figure 3 – SDN service . 23
Figure 4 – SRD service . 23
Figure 5 – MSRD service . 24
Figure 6 – CS service . 24
Figure 7 – Reset, Set value, Get value, Ident (local), DLSAP status, DLSAP activate,
DLSAP activate responder, DLSAP activate subscriber and DLSAP deactivate services . 47
Figure 8 – Event service . 47
Figure 9 – Ident (remote) service . 48

Table 1 – Summary of DL services and primitives . 22
Table 2 – SDA data ack primitives and parameters . 26
Table 3 – Values of DL_status for the SDA data ack service . 28
Table 4 – SDN data primitives and parameters . 29

---------------------- Page: 8 ----------------------

SIST EN 61158-3-3:2015
IEC 61158-3-3:2014 © IEC 2014 – 3 –
Table 5 – Values of DL_status for the SDN data service . 31
Table 6 – SRD data reply primitives and parameters . 32
Table 7 – Values of Update_status for the SRD data reply service . 33
Table 8 – Additional values of DL_status for the SRD data reply service . 34
Table 9 – SRD reply-update primitives and parameters . 34
Table 10 – Values of DL_status for the SRD reply-update service . 36
Table 11 – MSRD MCT data reply primitives and parameters . 37
Table 12 – MSRD DXM data reply primitive and parameters . 39
Table 13 – CS time event primitives and parameters . 41
Table 14 – Values of DL_status for the CS time event service . 42
Table 15 – CS clock value primitives and parameters . 42
Table 16 – Values of CS_status for the CS clock value service . 44
Table 17 – Values of DL_status for the CS clock value service . 44
Table 18 – Summary of DL-management services and primitives . 47
Table 19 – Reset primitives and parameters . 48
Table 20 – Values of DLM_status for the reset service . 48
Table 21 – Set value primitives and parameters . 49
Table 22 – Mandatory DLE-variables . 50
Table 23 – Optional DLE-variables . 50
Table 24 – Permissible values of mandatory DLE-variables . 51
Table 25 – Permissible values of optional DLE-variables . 51
Table 26 – Meaning of the values for the parameter isochronous_mode . 52
Table 27 – Default reaction times and operating parameters for a master station for
asynchronous transmission . 52
Table 28 – Default reaction times and operating parameters for a slave station with
asynchronous transmission . 52
Table 29 – Default reaction times and operating parameters for master stations for
coupling of synchronous and asynchronous transmission segments. 53
Table 30 – Default reaction times and operating parameter for slave stations for
coupling of synchronous and asynchronous transmission segments. 53
Table 31 – Values of DLM_status for the set value service . 53
Table 32 – Get value primitives and parameters . 54
Table 33 – Additional mandatory DLE-variables in master stations . 54
Table 34 – Permissible values of the additional DLE-variables in master stations . 55
Table 35 – Values of DLM_status for the get value service . 55
Table 36 – Event primitive and parameters . 55
Table 37 – Mandatory DLL events and fault types . 56
Table 38 – Permissible values of T . 56
SH
Table 39 – Ident primitives and parameters . 57
Table 40 – Ident_list for the ident service . 57
Table 41 – Values of DLM_status for the ident service (local) . 58
Table 42 – Values of DLM_status for the ident service (remote) . 58
Table 43 – DLSAP status primitives and parameters . 58
Table 44 – Values of DLM_status for the DLSAP status service . 59

---------------------- Page: 9 ----------------------

SIST EN 61158-3-3:2015
– 4 – IEC 61158-3-3:2014 © IEC 2014
Table 45 – DLSAP activate primitives and parameters . 60
Table 46 – DLSAP activate service_list . 60
Table 47 – DLSAP activate DLSDU_length_list (SDA, SDN, SRD, MSRD and CS) . 61
Table 48 – DLSDU lengths of SDA and SDN as used in the DLSAP activate service . 62
Table 49 – DLSDU lengths of SRD and MSRD as used in the (master station) DLSAP
activate service . 62
Table 50 – DLSDU lengths of CS as used in the DLSAP activate service . 62
Table 51 – Values of DLM_status for the DLSAP activate service . 62
Table 52 – DLSAP activate responder primitives and parameters . 63
Table 53 – DLSDU_length_list for the DLSAP activate responder service . 63
Table 54 – DLSDU length of SRD and MSRD as used in the DLSAP activate responder
service . 64
Table 55 – Values of DLM_status for the DLSAP activate responder service . 65
Table 56 – DLSAP activate subscriber primitives and parameters . 65
Table 57 – DLSDU_length_list for the DLSAP activate subscriber service . 66
Table 58 – DLSDU lengths of MSRD as used in the DLSAP activate subscriber service
(master and slave stations) . 66
Table 59 – Values of DLM_status for the DLSAP activate subscriber service . 66
Table 60 – DLSAP deactivate primitives and parameters . 67
Table 61 – Values of DLM_status for the DLSAP deactivate service . 67

---------------------- Page: 10 ----------------------

SIST EN 61158-3-3:2015
IEC 61158-3-3:2014 © IEC 2014 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

INDUSTRIAL COMMUNICATION NETWORKS –
FIELDBUS SPECIFICATIONS –

Part 3-3: Data-link layer service definition –
Type 3 elements


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
Attention is drawn to the fact that the use of the associated protocol type is restricted by its
intellectual-property-right holders. In all cases, the commitment to limited release of
intellectual-property-rights made by the holders of those rights permits a layer protocol type to
be used with other layer protocols of the same type, or in other type combinations explicitly
authorized by its intellectual-property-right holders.
NOTE Combinations of protocol types are specified in IEC 61784-1 and IEC 61784-2.
International Standard IEC 61158-3-3 has been prepared by subcommittee 65C: Industrial
networks, of IEC technical committee 65: Industrial-process measurement, control and
automation.
This second edition cancels and replaces the first edition published in 2007. This edition
constitutes a technical revision. The main changes with respect to the previous edition are
listed below:

---------------------- Page: 11 ----------------------

SIST EN 61158-3-3:2015
– 6 – IEC 61158-3-3:2014 © IEC 2014
– Two notes in definitions modified.
The text of this standard is based on the following documents:
FDIS Report on voting
65C/759/FDIS 65C/769/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with ISO/IEC Directives, Part 2.
The list of all the parts of the IEC 61158 series, under the general title Industrial
communication networks – Fieldbus specifications, can be found on the IEC web site.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under http://webstore.iec.ch in the data related
to the specific publication. At this date, the publication will be:
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.

---------------------- Page: 12 ----------------------

SIST EN 61158-3-3:2015
IEC 61158-3-3:2014 © IEC 2014 – 7 –
INTRODUCTION
This part of IEC 61158 is one of a series produced to facilitate the interconnection of
automation system components. It is related to other standards in the set as defined by the
“three-layer” fieldbus reference model described in IEC 61158-1.
Throughout the set of fieldbus standards, the term “service” refers to the abstract capability
provided by one layer of the OSI Basic Reference Model to the layer immediately above.
Thus, the data-link layer service defined in this standard is a conceptual architectural service,
independent of administrative and implementation divisions.

---------------------- Page: 13 ----------------------

SIST EN 61158-3-3:2015
– 8 – IEC 61158-3-3:2014 © IEC 2014
INDUSTRIAL COMMUNICATION NETWORKS –
FIELDBUS SPECIFICATIONS –

Part 3-3: Data-link layer service definition –
Type 3 elements



1 Scope
1.1 General
This part of IEC 61158 provides common elements for basic time-critical messaging
communications between devices in an automation environment. The term “time-critical” is
used to represent the presence of a time-window, within which one or more specified actions
are required to be completed with some defined level of certainty. Failure to complete
specified actions within the time window risks failure of the applications requesting the
actions, with attendant risk to equipment, plant and possibly human life.
This standard defines in an abstract way the externally visible service provided by the Type 3
fieldbus data-link layer in terms of
a) the primitive actions and events of the service;
b) the parameters associated with each primitive action and event, and the form which they
take; and
c) the interrelationship between these actions and events, and their valid sequences.
The purpose of this standard is to define the services provided to
– the Type 3 fieldbus application layer at the boundary between the application and data-link
layers of the fieldbus reference model, and
– systems management at the boundary between the data-link layer and systems
management of the fieldbus reference model.
1.2 Specifications
The principal objective of this standard is to specify the characteristics of conceptual data-link
layer services suitable for time-critical communications, and thus supplement the OSI Basic
Reference Model in guiding the development of data-link protocols for time-critical
communications. A secondary objective is to provide migration paths from previously existing
industrial communications protocols.
This specification may be used as the basis for formal DL-Programming-Interfaces.
Nevertheless, it is not a formal programming interface, and any such interface will need to
address implementation issues not covered by this specification, including
a) the sizes and octet ordering of various multi-octet service parameters, and
b) the correlation of paired request and confirm, or indication and response, primitives.

---------------------- Page: 14 ----------------------

SIST EN 61158-3-3:2015
IEC 61158-3-3:2014 © IEC 2014 – 9 –
1.3 Conformance
This standard does not specify individual implementations or products, nor do they constrain
the implementations of data-link entities within industrial automation systems.
There is no conformance of equipment to this data-link layer service definition standard.
Instead, conformance is achieved through implementation of the corresponding data-link
protocol that fulfills the Type 1 data-link layer services defined in this standard.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and
are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any
amendments) applies.
NOTE All parts of the IEC 61158 series, as well as IEC 61784-1 and IEC 61784-2 are maintained simultaneously.
Cross-references to these documents within the text therefore refer to the editions as dated in this list of normative
references.
IEC 61158-1, Industrial communication networks – Fieldbus specifications – Part 1: Overview
and guidan
...