SIST EN ISO 8826-2:1998

SLOVENSKI STANDARD
SIST EN ISO 8826-2:1998
01-maj-1998
7HKQLþQHULVEH.RWDOQLOHåDMLGHO3RHQRVWDYOMHQRSULND]RYDQMHV
SRGUREQRVWPL
Technical drawings - Rolling bearings - Part 2: Detailed simplified representation (ISO
8826-2:1994)
Technische Zeichnungen - Wälzlager - Teil 2: Detaillierte vereinfachte Darstellung (ISO
8826-2:1994)
Dessins techniques - Roulements - Partie 2: Représentation simplifiée particuliere (ISO
8826-2:1994)
Ta slovenski standard je istoveten z: EN ISO 8826-2:1997
ICS:
01.100.20 Konstrukcijske risbe Mechanical engineering
drawings
21.100.20 Kotalni ležaji Rolling bearings
SIST EN ISO 8826-2:1998 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 8826-2:1998

---------------------- Page: 2 ----------------------

SIST EN ISO 8826-2:1998

---------------------- Page: 3 ----------------------

SIST EN ISO 8826-2:1998

---------------------- Page: 4 ----------------------

SIST EN ISO 8826-2:1998

---------------------- Page: 5 ----------------------

SIST EN ISO 8826-2:1998

---------------------- Page: 6 ----------------------

SIST EN ISO 8826-2:1998
INTERNATIONAL IS0
STANDARD 8826-2
First edition
1994-09-01
Technical drawings - Rolling bearings -
Part 2:
Detailed simplified representation
Des&s techniques - Roulements -
Par-tie 2: Rep&en ta Con simplifiee particuli&re
Reference number
IS0 88262: 1994(E)

---------------------- Page: 7 ----------------------

SIST EN ISO 8826-2:1998
IS0 8826=2:1994(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work
of preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission
(I EC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard IS0 8826-2 was prepared by Technical Committee
ISODC 10, Technical drawings, product definition and related documen-
ta tion.
IS0 8826 consists of the following parts, under the general title Technica/
drawings - Rolling bearings:
- Part 7: General simplified representation
- Part 2: Detailed simplified representation
Annex A of this part of IS0 8826 is for information only.
0 IS0 1994
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means electronic or mechanical, including photocopyrng and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-1211 Geneve 20 l Switzerland
Printed in Switzerland
ii

---------------------- Page: 8 ----------------------

SIST EN ISO 8826-2:1998
0 IS0
IS0 8826-2: 1994(E)
Introduction
IS0 8826 provides rules for the simplified representation of rolling
bearings.
The principle of drawing practice is to depict the object to scale using
lines. In simplified representations, only essential features are shown,
preferably in outline (in order to save time and effort).
The degree of simplification depends on the kind of object represented,
the scale of the drawing and the purpose of the documentation. This
means that either a general simplified representation or a detailed one
may be used. A detailed representation shows more details of rolling
bearings, for example the number of rows or the possibility of alignment.
In order to avoid misunderstandings, only one kind of simplification, either
the general or the detailed simplified representation, should be used on a
drawing.

---------------------- Page: 9 ----------------------

SIST EN ISO 8826-2:1998
This page intentionally left blank

---------------------- Page: 10 ----------------------

SIST EN ISO 8826-2:1998
INTERNATIONAL STANDARD 0 IS0 IS0 8826-2: 1994(E)
Technical drawings - Rolling bearings -
Part 2:
Detailed simplified representation
IS0 582:-*I, Rolling bearings - Metric series -
1 Scope
Chamfer dimension limits.
This part of IS0 8826 specifies a detailed simplified
IS0 1206: 1982, Needle roller bearings - Light and
representation for various rolling bearings. This rep-
medium series - Dimensions and tolerances.
resentation should be used in cases where it is not
necessary to show the exact shape and details of the
IS0 3030: 1974, Needle roller bearings - Needle rol-
rolling bearings, for example in assembly drawings.
ler and cage assemblies - Metric series - Part I:
Radial needle roller and cage assemblies - Boundary
2 Normative references
dimensions and tolerances.
The following standards contain provisions which,
IS0 3031: 1979, Needle roller bearings - Thrust nee-
through reference in this text, constitute provisions
dle roller and cage assemblies, thrust washers - Di-
of this part of IS0 8826. At the time of publication, the
mensions and tolerances.
editions indicated were valid. All standards are subject
to revision, and parties to agreements based on this
IS0 3245: 1974, Rolling bearings - Needle roller
part of IS0 8826 are encouraged to investigate the
bearings, drawn cup, without inner ring - Metric se-
possibility of applying the most recent editions of the
ries - Boundary dimensions and tolerances.
standards indicated below. Members of IEC and IS0
maintain registers of currently valid nternational
IS0 8443: 1985, Radial ball bearings with flanged
Standards.
outer ring - Flange dimensions.
bearings -
I SO 15: 1981, Rolling bearings - Radial
IS0 8826-l :I 989, Technical drawings - Rolling
Boundary dimensions - General plan.
bearings
...