Bitumen and bituminous binders - Determination of kinematic viscosity

This European Standard specifies a method for the determination of the kinematic viscosity of bituminous binders at 60 °C and 135 °C, in a range from 6 mm²/s to 300 000 mm²/s. Other temperatures are possible if calibration constants are known. Bituminous emulsions are not covered within the scope of this method.
NOTE   Emulsions containing bituminous binders are not considered to be covered by this method. The method can be used for anhydrous binders obtained from emulsions (stabilised and/or recovered binders).
Results for this method can be used to calculate dynamic viscosity when the density of the test material is known or can be determined.
WARNING - Use of this European Standard can involve hazardous materials, operations and equipment. This European Standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this European Standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Bitumen und bitumenhaltige Bindemittel - Bestimmung der kinematischen Viskosität

Diese Europäische Norm legt ein Verfahren zur Bestimmung der kinematischen Viskosität von bitumenhaltigen Bindemitteln bei 60 °C und 135 °C in einem Bereich von 6 mm2/s bis 300 000 mm2/s fest. Andere Temperaturen sind möglich, sofern Kalibrierungskonstanten bekannt sind. Dieses Verfahren gilt nicht für Bitumenemulsionen.
ANMERKUNG   Emulsionen, die bitumenhaltige Bindemittel enthalten, gelten als von diesem Verfahren nicht betroffen. Das Verfahren kann auf wasserfreie Bindemittel angewendet werden, die aus Emulsionen erhalten wurden (stabilisierte und/oder rückgewonnene Bindemittel).
Die nach diesem Verfahren erhaltenen Ergebnisse können zur Berechnung der dynamischen Viskosität verwendet werden, wenn die Dichte des Prüfmaterials bekannt ist oder bestimmt werden kann.
WARNUNG — Die Anwendung dieser Europäischen Norm kann den Umgang mit gefährlichen Substanzen und Ausrüstungsteilen und die Ausführung gefährlicher Arbeitsgänge einschließen. Diese Europäische Norm erhebt nicht den Anspruch, alle mit ihrer Anwendung verbundenen Sicherheitsprobleme anzusprechen. Es liegt in der Verantwortung des Anwenders dieser Europäischen Norm, geeignete Verhaltensregeln zur Sicherheit und Gesundheit festzulegen und die Anwendbarkeit ein¬schränkender Vorschriften vor der Anwendung zu bestimmen.

Bitumes et liants bitumineux - Détermination de la viscosité cinématique

La présente Norme européenne prescrit une méthode de détermination de la viscosité cinématique de liants bitumineux à 60 °C et 135 °C, dans l'intervalle de 6 mm2/s à 300 000 mm2/s. D’autres températures sont possibles si les constantes de calibration sont connues. Le domaine d’application de la présente méthode ne comprend pas les émulsions bitumineuses.
NOTE   Les émulsions contenant des liants bitumineux ne sont pas couverts par la présente méthode. Cette méthode peut être utilisée pour les liants anhydres obtenus à partir d’émulsions (liants stabilisés et/ou récupérés).
Les résultats de la présente méthode peuvent être utilisés pour calculer la viscosité dynamique quand la masse volumique du matériau d'essai est connue ou peut être déterminée.
AVERTISSEMENT — L'utilisation de la présente Norme européenne peut impliquer le recours à de produits, des opérations et des équipements à caractères dangereux. La présente Norme européenne n'est pas censée aborder tous les problèmes de sécurité concernés par son usage. Il est de la responsabilité de l'utilisateur de consulter et d'établir des règles de sécurité et d'hygiène appropriées et de déterminer l'applicabilité des restrictions réglementaires avant utilisation.

Bitumen in bitumenska veziva - Določanje kinematične viskoznosti

Ta evropski standard določa metodo za določanje kinematične viskoznosti bitumenskih veziv pri temperaturi 60 °C in 135 °C v razponu od 6 mm²/s do 300 000 mm²/s. Druge temperature so možne, če so poznane kalibracijske konstante. Bitumenske emulzije niso zajete v tej metodi.
OPOMBA   Emulzij z bitumenskimi vezivi ta metoda ne zajema. Metoda se lahko uporablja za brezvodna veziva, pridobljena iz emulzij (stabilizirana in/ali ponovno pridobljena veziva).
Rezultati te metode se lahko uporabijo za izračun dinamične viskoznosti, ko je gostota preskusnega materiala poznana ali jo je mogoče določiti.
OPOZORILO – pri uporabi tega evropskega standarda so lahko prisotni nevarni materiali, postopki in oprema. Ta evropski standard ne obravnava vseh varnostnih težav, ki se nanašajo na njegovo uporabo. Za vzpostavitev ustreznih varnostnih in zdravstvenih praks ter za določitev uporabnosti regulativnih omejitev pred uporabo je odgovoren uporabnik tega evropskega standarda.

General Information

Status
Withdrawn
Public Enquiry End Date
19-May-2013
Publication Date
24-Nov-2014
Withdrawal Date
11-Oct-2023
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
12-Sep-2023
Due Date
05-Oct-2023
Completion Date
12-Oct-2023

Relations

Buy Standard

Standard
EN 12595:2014
English language
18 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 12595:2013
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bitumen und bitumenhaltige Bindemittel - Bestimmung der kinematischen ViskositätBitumes et liants bitumineux - Détermination de la viscosité cinématiqueBitumen and bituminous binders - Determination of kinematic viscosity91.100.50Veziva. Tesnilni materialiBinders. Sealing materials75.140Voski, bitumni in drugi naftni proizvodiWaxes, bituminous materials and other petroleum productsICS:Ta slovenski standard je istoveten z:EN 12595:2014SIST EN 12595:2014en,fr,de01-december-2014SIST EN 12595:2014SLOVENSKI
STANDARDSIST EN 12595:20071DGRPHãþD



SIST EN 12595:2014



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12595
November 2014 ICS 75.140; 91.100.50 Supersedes EN 12595:2007English Version
Bitumen and bituminous binders - Determination of kinematic viscosity
Bitumes et liants bitumineux - Détermination de la viscosité cinématique
Bitumen und bitumenhaltige Bindemittel - Bestimmung der kinematischen Viskosität This European Standard was approved by CEN on 16 August 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12595:2014 ESIST EN 12595:2014



EN 12595:2014 (E) 2 Contents Page Foreword .3 1 Scope .4 2 Normative references .4 3 Terms and definitions .4 4 Principle .5 5 Apparatus .5 6 Preparation of test samples .6 7 Procedure .7 8 Calculation .8 9 Expression of results .8 10 Precision .8 11 Test report .9 Annex A (normative)
Specifications of viscometers . 10 Annex B (informative)
Calibration of viscometers . 14 Annex C (informative)
Characteristics of thermometers. 17 Bibliography . 18
SIST EN 12595:2014



EN
...

SLOVENSKI STANDARD
oSIST prEN 12595:2013
01-april-2013
%LWXPHQLQELWXPHQVNDYH]LYD'RORþDQMHNLQHPDWLþQHYLVNR]QRVWL
Bitumen and bituminous binders - Determination of kinematic viscosity
Bitumen und bitumenhaltige Bindemittel - Bestimmung der kinematischen Viskosität
Bitumes et liants bitumineux - Détermination de la viscosité cinématique
Ta slovenski standard je istoveten z: prEN 12595
ICS:
75.140 Voski, bitumni in drugi naftni Waxes, bituminous materials
proizvodi and other petroleum products
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
oSIST prEN 12595:2013 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 12595:2013

---------------------- Page: 2 ----------------------
oSIST prEN 12595:2013


EUROPEAN STANDARD
DRAFT
prEN 12595
NORME EUROPÉENNE

EUROPÄISCHE NORM

January 2013
ICS 75.140; 91.100.50 Will supersede EN 12595:2007
English Version
Bitumen and bituminous binders - Determination of kinematic
viscosity
Bitumes et liants bitumineux - Détermination de la viscosité Bitumen und bitumenhaltige Bindemittel - Bestimmung der
cinématique kinematischen Viskosität
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 336.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12595:2013: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 12595:2013
prEN 12595:2013 (E)
Contents Page
Foreword .3
1 Scope .4
2 Normative references .4
3 Terms and definitions .4
4 Principle .5
5 Apparatus .5
6 Preparation of test samples .6
7 Procedure .7
8 Calculation .8
9 Expression of results .8
10 Precision .8
11 Test report .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.