SIST EN ISO 9409-1:2004

SLOVENSKI STANDARD
SIST EN ISO 9409-1:2004
01-september-2004
1DGRPHãþD
SIST EN ISO 9409-1:2003
0DQLSXOLUQLLQGXVWULMVNLURERWL±0HKDQVNLYPHVQLNL±GHO3ORãþHREOLND$,62

Manipulating industrial robots - Mechanical interfaces - Part 1: Plates (ISO 9409-1:2004)
Industrieroboter - Mechanische Schnittstellen - Teil 1: Platten (ISO 9409-1:2004)
Robots manipulateurs industriels - Interfaces mécaniques - Partie 1: Interfaces a plateau
(ISO 9409-1:2004)
Ta slovenski standard je istoveten z: EN ISO 9409-1:2004
ICS:
25.040.30 Industrijski roboti. Industrial robots.
Manipulatorji Manipulators
SIST EN ISO 9409-1:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 9409-1:2004

---------------------- Page: 2 ----------------------

SIST EN ISO 9409-1:2004
EUROPEAN STANDARD
EN ISO 9409-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2004
ICS 25.040.30 Supersedes EN ISO 9409-1:1996
English version
Manipulating industrial robots - Mechanical interfaces - Part 1:
Plates (ISO 9409-1:2004)
Robots manipulateurs industriels - Interfaces mécaniques - Industrieroboter - Mechanische Schnittstellen - Teil 1:
Partie 1: Interfaces à plateau (ISO 9409-1:2004) Platten (ISO 9409-1:2004)
This European Standard was approved by CEN on 2 February 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9409-1:2004 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 9409-1:2004
EN ISO 9409-1:2004 (E)
Foreword
This document (EN ISO 9409-1:2004) has been prepared by Technical Committee ISO/TC 184
"Industrial automation systems and integration" in collaboration with Technical Committee
CEN/TC 310 "Advanced Manufacturing Technologies", the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by September 2004, and conflicting national
standards shall be withdrawn at the latest by September 2004.
This document supersedes EN ISO 9409-1:1996.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 9409-1:2004 has been approved by CEN as EN ISO 9409-1:2004 without any
modifications.
2

---------------------- Page: 4 ----------------------

SIST EN ISO 9409-1:2004


INTERNATIONAL ISO
STANDARD 9409-1
Third edition
2004-03-01


Manipulating industrial robots —
Mechanical interfaces —
Part 1:
Plates
Robots manipulateurs industriels — Interfaces mécaniques —
Partie 1: Interfaces à plateau





Reference number
ISO 9409-1:2004(E)
©
ISO 2004

---------------------- Page: 5 ----------------------

SIST EN ISO 9409-1:2004
ISO 9409-1:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2004 – All rights reserved

---------------------- Page: 6 ----------------------

SIST EN ISO 9409-1:2004
ISO 9409-1:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 9409-1 was prepar
...