SIST EN 840-2:2014

SLOVENSKI STANDARD
SIST EN 840-2:2014
01-marec-2014
1DGRPHãþD
SIST EN 840-2:2004
3UHPLþQL]DERMQLNL]DRGSDGNHLQ]DUHFLNOLUDQMHGHO=DERMQLNLQDãWLULKNROHVLK
VSURVWRUQLQRGROLQUDYQLPLSRNURYRPL]DL]WUHVDOQLNH]URNDPDLQDOL
JODYQLNRP0HUHLQREOLND
Mobile waste and recycling containers - Part 2: Containers with 4 wheels with a capacity
up to 1 300 l with flat lid(s), for trunnion and/or comb lifting devices - Dimensions and
design
Fahrbare Abfall- und Wertstoffbehälter - Teil 2: Behälter mit 4 Rädern und einem
Nennvolumen bis 1300 l mit Flachdeckel(n), für Schüttungen mit Zapfenaufnahme
und/oder für Kammschüttungen - Maße und Formgebung
Conteneurs roulants à ordures ménagères et recyclables - Partie 2: Conteneurs à 4
roues de capacité inférieure ou égale à 1300 l à couvercle(s) plat(s), pour lève-
conteneurs par tourillon et/ou à peigne - Dimensions et conception
Ta slovenski standard je istoveten z: EN 840-2:2012
ICS:
13.030.40 Naprave in oprema za Installations and equipment
odstranjevanje in obdelavo for waste disposal and
odpadkov treatment
SIST EN 840-2:2014 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 840-2:2014

---------------------- Page: 2 ----------------------

SIST EN 840-2:2014


EUROPEAN STANDARD
EN 840-2

NORME EUROPÉENNE

EUROPÄISCHE NORM
December 2012
ICS 13.030.40 Supersedes EN 840-2:2004
English Version
Mobile waste and recycling containers - Part 2: Containers with
4 wheels with a capacity up to 1 300 l with flat lid(s), for trunnion
and/or comb lifting devices - Dimensions and design
Conteneurs roulants à ordures ménagères et recyclables - Fahrbare Abfall- und Wertstoffbehälter - Teil 2: Behälter mit
Partie 3: Conteneurs à 4 roues de capacité inférieure ou 4 Rädern und einem Nennvolumen bis 1300 l mit
égale à 1300 l à couvercle(s) bombé(s), pour lève- Flachdeckel(n), für Schüttungen mit Zapfenaufnahme
conteneurs par tourillon et/ou à peigne - Dimensions et und/oder für Kammschüttungen - Maße und Formgebung
conception
This European Standard was approved by CEN on 22 September 2012.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 840-2:2012: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 840-2:2014
EN 840-2:2012 (E)
Contents Page
Foreword .3
1 Scope .4
2 Normative references .4
3 Terms and definitions .4
4 Volumes .5
5 Dimensions and design .5
6 Nominal mass .6
7 Safety and health requirements .6
8 Testing .6
9 Marking .6
10 Designation .7
Annex A (informative) Recommendations for manufacturers of lifting devices . 15
Annex B (informative) A-Deviations . 17
Bibliography . 18

2

---------------------- Page: 4 ----------------------

SIST EN 840-2:2014
EN 840-2:2012 (E)
Foreword
This document (EN 840-2:2012) has been prepared by Technical Committee CEN/TC 183 “Waste
management”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2013, and conflicting national standards shall be withdrawn at
the latest by June 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 840-2:2004.
Technical changes since the latest edition:
 The content was adapted to the current state of the art and revised editorially.
 Figure 3 has been deleted.
 Frontal receivers Form B and C have been deleted. Figure 2 has been changed accordingly.
This European Standard is one part of the series of standards of EN 840 with the main title Mobile waste and
recycling containers comprising the following parts:
 Part 1: Containers with 2 wheels with a capacity up to 400 l for comb lifting devices  Dimensions and
design;
 Part 2: Containers with 4 wheels with a capacity up to 1 300 l with flat lid(s), for trunnion and/or comb
lifting devices  Dimensions and design (the present document);
 Part 3: Containers with 4 wheels with a capacity up to 1 300 l with dome lid(s), for trunnion and/or comb
lifting devices  Dimensions and design;
 Part 4: Containers with 4 wheels with a capacity up to 1 700 l with flat lid(s), for wide trunnion or BG-
and/or wide comb lifting devices  Dimensions and design;
 Part 5: Performance requirements and test methods;
 Part 6: Safety and health requirements.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
3

---------------------- Page: 5 ----------------------

SIST EN 840-2:2014
EN 840-2:2012 (E)
1 Scope
This European Standard specifies dimensions and design requirements of mobile waste containers with
4 wheels, with flat lid(s) and capacity up to 1 300 l to be used by trunnion and/or comb lifting device.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 840-5, Mobile waste and recycling containers — Part 5: Performance requirements and test methods
EN 840-6:2012, Mobile waste and recycling containers — Part 6: Safety and health requirements
EN 1501-1, Refuse collection vehicles — General requirements and safety requirements — Part 1: Rear
loaded refuse collection vehicles
EN 1501-5:2011, Refuse collection vehicles — General requirements and safety requirements — Part 5:
Lifting devices for refuse collection vehicles
EN ISO 11469, Plastics — Generic identification and marking of plastics products (ISO 11469)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
NOTE Terms for components of mobile waste containers and lifting devices in three languages are given in Annex A
of EN 840-1:2012.
3.1
mobile waste and recycling container
appropriately designed container fitted with wheels intended to temporarily store waste
3.2
lifting device
structure which picks-up, tilts and empties containers
3.3
comb lifting device
lifting device in which the picking-up system consists of a row of teeth and a locking system to retain the
container during emptying
3.4
trunnion lifting device
lifting device in which the picking-up system consists of a pair of arms with automatic locking mechanism to fit
the trunnion to retain the container during emptying
3.5
volume
total space inside the container when the lid is closed
Note 1 to entry: See Table 1.
4

---------------------- Page: 6 ----------------------

SIST EN 840-2:2014
EN 840-2:2012 (E)
3.6
nominal volume
capacity
volume stated by the manufacturer
Note 1 to entry: See Table 1 without tolerances.
Note 2 to entry: The English term "capacity" and the French term "capacité" are translated in the German version by
the term "Nennvolumen".
3.7
nominal mass
mass, which is calculated as given in Clause 6
3.8
total permissible mass
mass of the container plus the nominal mass
3.9
functional and safety dimensions
essential dimensions which ensure the functionality and interchangeability of the container with the compatible
lifting device and which are necessary for the operator's safety and health
4 Volumes
This part of EN 840 identifies the two classes of containers:
 Class I - small size (nominal volume up to 1 000 l);
 Class II - large size (nominal volume between 1 000 l and 1 300 l).
Within the two above-mentioned classes of containers the following volumes are identified: 500 l, 660 l, 770 l,
1 000 l, 1 100 l and 1 200 l. Nominal volumes different from those referenced can be used by agreement
between user and manufacturer. The tolerance of the volumes shall be ± 5 % maximum measured according
to EN 840-5.
5 Dimensions and design
5.1 The design of the containers need not correspond to the drawings given in Figure 1. The functional
dimensions given in Table 1 shall be respected. Recommendations for manufacturers of lifting devices are
given in Annex A (see also EN 1501-1).
5.2 The container shall be constructed so that when it is unloaded or loaded with a nominal load
(see Clause 6), it fits on an approved compatible lifting device. It shall be automatically locked safely into the
lifting device during the lifting operation. If the container is equipped with a comb receiver, it shall correspond
to Figure 2.
5.3 The lid(s) shall cover the opening of the container completely. It shall be opened easily by itself during
the emptying cycle it/they shall be made with at least two fixing points and have at least one means of
opening.
5.4 Handles fitted in front of the trunnion shall have a measurement over the handles of 10 mm less than
the actual measurement in Table 1, dimension N° 33. The h
...