SIST EN ISO 1307:2009

SLOVENSKI STANDARD
SIST EN ISO 1307:2009
01-februar-2009
1DGRPHãþD
SIST EN ISO 1307:2000
*XPHQHLQSROLPHUQHFHYL9HOLNRVWLFHYLQDMPDQMãLLQQDMYHþMLQRWUDQMLSUHPHULLQ
WROHUDQFHGROåLQ,62
Rubber and plastics hoses - Hose sizes, minimum and maximum inside diameters, and
tolerances on cut-to-length hoses (ISO 1307:2006)
Gummi- und Kunststoffschläuche - Schlauchmaße, Kleinst- und Größt-
Innendurchmesser, und Toleranzen bei abgelängten Schläuchen (ISO 1307:2006)
Tuyaux en caoutchouc et en plastique - Diametres nominaux, diametres intérieurs
minimaux et maximaux, et tolérances sur la longueur de coupe (ISO 1307:2006)
Ta slovenski standard je istoveten z: EN ISO 1307:2008
ICS:
23.040.70 Gumene cevi in armature Hoses and hose assemblies
SIST EN ISO 1307:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 1307:2009

---------------------- Page: 2 ----------------------

SIST EN ISO 1307:2009
EUROPEAN STANDARD
EN ISO 1307
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2008
ICS 23.040.70 Supersedes EN ISO 1307:1995
English Version
Rubber and plastics hoses - Hose sizes, minimum and
maximum inside diameters, and tolerances on cut-to-length
hoses (ISO 1307:2006)
Tuyaux en caoutchouc et en plastique - Dimensions des Gummi- und Kunststoffschläuche - Schlauchmaße, Kleinst-
tuyaux, diamètres intérieurs minimaux et maximaux, et und Größt-Innendurchmesser, und Toleranzen bei
tolérances sur la longueur de coupe (ISO 1307:2006) abgelängten Schläuchen (ISO 1307:2006)
This European Standard was approved by CEN on 26 December 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1307:2008: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 1307:2009
EN ISO 1307:2008 (E)






Foreword



The text of ISO 1307:2006 has been prepared by Technical Committee ISO/TC 45 "Rubber and
rubber products” of the International Organization for Standardization (ISO) and has been taken
over as EN ISO 1307:2008 by Technical Committee CEN/TC 218 "Rubber and plastics hoses
and hose assemblies", the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by July 2008, and conflicting national standards
shall be withdrawn at the latest by July 2008.
Attention is drawn to the possibility that some of the elements of this document may be the
subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any
or all such patent rights.
This document supersedes EN ISO 1307:1995.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United
Kingdom.

Endorsement notice

The text of ISO 1307:2006 has been approved by CEN as EN ISO 1307:2008 without any
modifications.

2

---------------------- Page: 4 ----------------------

SIST EN ISO 1307:2009


INTERNATIONAL ISO
STANDARD 1307
Fourth edition
2006-09-15

Rubber and plastics hoses — Hose sizes,
minimum and maximum inside diameters,
and tolerances on cut-to-length hoses
Tuyaux en caoutchouc et en plastique — Diamètres nominaux,
diamètres intérieurs minimaux et maximaux, et tolérances sur la
longueur de coupe




Reference number
ISO 1307:2006(E)
©
ISO 2006

---------------------- Page: 5 ----------------------

SIST EN ISO 1307:2009
ISO 1307:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or
...