SIST EN 60424-8:2016

SLOVENSKI STANDARD
SIST EN 60424-8:2016
01-marec-2016
Feritna jedra - Smernice o omejitvah površinskih nepravilnostih - 8. del: Jedra PQ
Ferrite cores - Guidelines on the limits of surface irregularities - Part 8: PQ-cores
Noyaux ferrites - Guide relatif aux limites des irrégularités de surface - Partie 8: Noyaux
PQ
Ta slovenski standard je istoveten z: EN 60424-8:2015
ICS:
29.100.10 Magnetne komponente Magnetic components
SIST EN 60424-8:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60424-8:2016

---------------------- Page: 2 ----------------------

SIST EN 60424-8:2016


EUROPEAN STANDARD EN 60424-8

NORME EUROPÉENNE

EUROPÄISCHE NORM
December 2015
ICS 29.100.10

English Version
Ferrite cores - Guidelines on the limits of surface irregularities -
Part 8: PQ-cores
(IEC 60424-8:2015)
Noyaux ferrites - Lignes directrices relatives aux limites des Ferritkerne - Leitfaden für Grenzwerte von sichtbaren
irrégularités de surface - Partie 8: Noyaux PQ Beschädigungen der Kernoberfläche - Teil 8: PQ-Kerne
(IEC 60424-8:2015) (IEC 60424-8:2015)
This European Standard was approved by CENELEC on 2015-09-09. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 60424-8:2015 E

---------------------- Page: 3 ----------------------

SIST EN 60424-8:2016
EN 60424-8:2015
European foreword
The text of document 51/1078/CDV, future edition 1 of IEC 60424-8, prepared by IEC/TC 51
"Magnetic components and ferrite materials" was submitted to the IEC-CENELEC parallel vote and
approved by CENELEC as EN 60424-8:2015.
The following dates are fixed:
(dop) 2016-06-09
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
(dow) 2018-09-09
• latest date by which the national standards conflicting with
the document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 60424-8:2015 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60401-2 NOTE Harmonized as EN 60401-2.
IEC 62317-13 NOTE Harmonized as EN 62317-13.
2

---------------------- Page: 4 ----------------------

SIST EN 60424-8:2016
EN 60424-8:2015
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is
available here: www.cenelec.eu.

Publication Year Title EN/HD Year
IEC 60401-1 -  Terms and nomenclature for cores made of EN 60401-1 -
magnetically soft ferrites -
Part 1: Terms used for physical
irregularities
IEC 60424-1 -  Ferrite cores - Guide on the limits of EN 60424-1 -
surface irregularities -
Part 1: General specification

3

---------------------- Page: 5 ----------------------

SIST EN 60424-8:2016

---------------------- Page: 6 ----------------------

SIST EN 60424-8:2016



IEC 60424-8

®


Edition 1.0 2015-08




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Ferrite cores – Guidelines on the limits of surface irregularities –

Part 8: PQ-cores




Noyaux ferrites – Lignes directrices relatives aux limites des irrégularités de

surface –

Partie 8: Noyaux PQ
















INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 29.100.10 ISBN 978-2-8322-2803-6



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60424-8:2016
– 2 – IEC 60424-8:2015 © IEC 2015
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Limits of surface irregularities . 6
4.1 Chips and ragged edges . 6
4.1.1 Chips and ragged edges located on the mating surface . 6
4.1.2 Chips located on other surfaces . 6
4.2 Cracks . 9
4.3 Pull-out . 10
4.4 Crystallites . 10
4.5 Flash . 11
4.6 Pores . 11
Bibliography . 13

Figure 1 – Examples of surface irregularities . 5
Figure 2 – Chips and ragged edges location . 6
Figure 3 – Cracks location . 9
Figure 4 – Reference dimensions for PQ-cores . 9
Figure 5 – Pull-out location . 10
Figure 6 – Crystallites location . 11
Figure 7 – Flash location. 11
Figure 8 – Pores location . 12

Table 1 – Limits for allowable chipping areas . 7
Table 2 – Area and length reference of irregularities for visual inspection . 8
Table 3 – Limits for cracks . 10

---------------------- Page: 8 ----------------------

SIST EN 60424-8:2016
IEC 60424-8:2015 © IEC 2015 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FERRITE CORES –
GUIDELINES ON THE LIMITS OF SURFACE IRREGULARITIES –

Part 8: PQ-cores

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The f
...