Small craft, engine-driven - Field of vision from helm position (ISO 11591:2011)

This International Standard specifies requirements for the field of vision from the helm position, forward and astern, in engine-driven small craft of up to 24 m length of hull. It is not applicable to: - tiller-steered craft (3.10) with maximum speed less than 10 knots; - sailing craft (3.11).

Motorgetriebene kleine Wasserfahrzeuge - Sichtfeld vom Steuerstand (ISO 11591:2011)

Diese Internationale Norm legt Anforderungen an das Sichtfeld vom Steuerstand aus nach vorn und hinten in motorgetriebenen kleinen Wasserfahrzeugen mit einer Rumpflänge bis 24 m fest.
Die folgenden Wasserfahrzeuge sind von der Anwendung dieser Internationalen Norm ausgenommen:
   Segelboote;
   Wasserfahrzeuge, die mit einer Ruderpinne gesteuert werden (3.7) und weniger als 10 kn (10 Knoten) Geschwindigkeit erreichen.
ANMERKUNG   Fahrweise und Geschwindigkeit können bei kleinen motorgetriebenen Fahrzeugen zu Trimmwinkeln führen, welche die Sicht nach Voraus zeitweise einschränken. Die Internationale Norm kann nicht sicherstellen, dass ein Fahrzeug beim Auftreten großer Trimmwinkel während des Übergangs von Verdrängungs- zu Gleitfahrt ohne Sichtfeldverlust vom Steuerstand aus betrieben werden kann.

Petits navires à moteur - Champ de visibilité depuis le poste de pilotage (ISO 11591:2011)

L'ISO 11591:2011 spécifie les exigences relatives au champ de vision vers l'avant et vers l'arrière depuis le poste de pilotage des petits navires à moteur dont la longueur de coque est inférieure ou égale à 24 m.
Elle n'est pas applicable aux bateaux à barre franche dont la vitesse maximale est inférieure à 10 noeuds ou aux bateaux à voile.

Mala plovila na motorni pogon - Vidno polje izza krmilne mize (ISO 11591:2011)

Ta mednarodni standard določa zahteve za vidno polje izza krmilne mize, naprej in nazaj, pri manjših plovilih na motorni pogon dolžine trupa do 24 m. Ne velja za: - plovila s krmilom (3.10) z največjo hitrostjo manj kot 10 vozlov; - jadralna plovila (3.11).

General Information

Status
Withdrawn
Public Enquiry End Date
31-Mar-2008
Publication Date
13-Oct-2011
Withdrawal Date
20-May-2019
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
20-May-2019
Due Date
12-Jun-2019
Completion Date
21-May-2019

Relations

Buy Standard

Standard
EN ISO 11591:2011
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 11591:2008
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 11591:2011
01-november-2011
1DGRPHãþD
SIST EN ISO 11591:2001
Mala plovila na motorni pogon - Vidno polje izza krmilne mize (ISO 11591:2011)
Small craft, engine-driven - Field of vision from helm position (ISO 11591:2011)
Motorgetriebene kleine Wasserfahrzeuge - Sichtfeld vom Steuerstand (ISO 11591:2011)
Petits navires à moteur - Champ de visibilité depuis le poste de pilotage (ISO
11591:2011)
Ta slovenski standard je istoveten z: EN ISO 11591:2011
ICS:
47.080 ýROQL Small craft
SIST EN ISO 11591:2011 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 11591:2011

---------------------- Page: 2 ----------------------

SIST EN ISO 11591:2011


EUROPEAN STANDARD
EN ISO 11591

NORME EUROPÉENNE

EUROPÄISCHE NORM
September 2011
ICS 47.080 Supersedes EN ISO 11591:2000
English Version
Small craft, engine-driven - Field of vision from helm position
(ISO 11591:2011)
Petits navires à moteur - Champ de vision depuis le poste Motorgetriebene kleine Wasserfahrzeuge - Sichtfeld vom
de pilotage (ISO 11591:2011) Steuerstand (ISO 11591:2011)
This European Standard was approved by CEN on 10 September 2011.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11591:2011: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 11591:2011
EN ISO 11591:2011 (E)
Contents Page
Foreword .3
Annex ZA (informative)  Relationship between this European Standard and the Essential
Requirements of EU Directive 94/25/EC as amended by Directive 2003/44/EC .4

2

---------------------- Page: 4 ----------------------

SIST EN ISO 11591:2011
EN ISO 11591:2011 (E)
Foreword
This document (EN ISO 11591:2011) has been prepared by Technical Committee ISO/TC 188 "Small craft".
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by March 2012, and conflicting national standards shall be withdrawn at
the latest by March 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11591:2000.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive.
For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 11591:2011 has been approved by CEN as a EN ISO 11591:2011 without any modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 11591:2011
EN ISO 11591:2011 (E)
Annex ZA
(informative)

Relationship between this European Standard and the Essential
Requirements of EU Directive 94/25/EC as amended by Directive
2003/44/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission to
provide one means of conforming to Essential Requirements of the New Approach Directive 94/25/EC as
amended by Directive 2003/44/EC.

Once this standard is cited in the Official Journal of the European Union under that Directive and has been
implemented as a national standard in at least one Member State, compliance with the normative clauses of
this standard given in Table ZA.1 confers, within the limits of the scope of this standard, a presumption of
conformity with the corresponding Essential Requirements of that Directive and associated EFTA regulations.

Table ZA.1 — Correspondence between this European Standard and Directive 94/25/EC as amended
by Directive 2003/44/EC

Clause(s)/sub-clause(s) of this Essential requirements (ERs) of EU Qualifying remarks/Notes
European Standard Directive 94/25/EC as amended by
Directive 2003/44/EC
All clauses 2.4 of Annex I Excludes sailing craft and tiller steered
craft with a maximum speed less than
10 knots.
Visibility from the main steering
position
Clause 7 2.4 of Annex I
Owner’s manual


WARNING — Other requirements and other EU Directives may be applicable to the products falling
within the scope of this standard.
4

---------------------- Page: 6 ----------------------

SIST EN ISO 11591:2011
INTERNATIONAL ISO
STANDARD 11591
Second edition
2011-09-15
Small craft, engine-driven — Field of
vision from helm position
Petits navires à moteur — Champ de vision depuis le poste de pilotage
Reference number
ISO 11591:2011(E)
©
ISO 2011

---------------------- Page: 7 ----------------------

SIST EN ISO 11591:2011
ISO 11591:2011(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 11591:2011
ISO 11591:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11591 was prepared by Technical Committee ISO/TC 188, Small craft.
This second edition cancels and replaces the first edition (ISO 11591:2000), which has been technically revised.
© ISO 2011 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 11591:2011

---------------------- Page: 10 ----------------------

SIST EN ISO 11591:2011
INTERNATIONAL STANDARD ISO 11591:2011(E)
Small craft, engine-driven — Field of vision from helm position
1 Scope
This International Standard specifies requirements for the field of vision from the helm position, forward and
astern, in engine-driven small craft of up to 24 m length of hull.
It is not applicable to:
— tiller-steered craft (3.10) with maximum speed less than 10 knots;
— sailing craft (3.11).
NOTE Small engine driven craft can be operated in a manner and at certain speeds causing trim angles such that
vision forward is temporarily obscured. This International Standard cannot assure that a craft can be operated without some
temporary loss of vision from the helm position while operating at high trim angles during the transition from displacement
to planing mode.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced document
(including any amendments) applies.
ISO 3538:1997, Road vehicles — Safety glazing materials — Test methods for optical properties
ISO 7000:2004, Graphical symbols for use on equipment — Index and synopsis
ISO 8666, Small craft — Principal data
ISO 11192, Small craft — Graphical symbols
ISO 11592, Small craft less than 8 m length of hull — Determination of maximum propulsion power rating
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
high eye position
〈helmsman in standing position〉 position 1 730 mm above the surface on which the helmsman stands, 400 mm
from the centre of the steering-wheel rim
See Figure 1.
3.2
high eye position
〈helmsman in seated position〉 position 840 mm above the intersection of the compressed seat and the seat
back, 400 mm from the centre of the steering-wheel rim
See Figure 2.
© ISO 2011 – All rights reserved 1

---------------------- Page: 11 ----------------------

SIST EN ISO 11591:2011
ISO 11591:2011(E)
3.3
low eye position
〈helmsman in standing position〉 position 1 480 mm above the surface on which the helmsman stands, 400 mm
from the centre of the steering-wheel rim
See Figure 1.
3.4
low eye position
〈helmsman in seated position〉 position 690 mm above the intersection of the compressed seat and the seat-
back, 400 mm from the centre of the steering-wheel rim
See Figure 2.
3.5
compressed seat bottom
surface of the centre of the helm seat at the intersection of the seat-back and seat-bottom when compressed
by a 25 mm diameter spherical object under a vertical load of 100 N
See Figure 2.
Dimensions in millimetres
Key
1 high eye position
2 to horizon
3 low eye position
4 required vertical range of vision
5 lowest unobstructed line of vision
6 point of visual obstruction
Figure 1 — Eye positions and vertical range of vision — Helmsman in standing position
2 © ISO 2011 – All rights reserved

---------------------- Page: 12 ----------------------

SIST EN ISO 11591:2011
ISO 11591:2011(E)
Dimensions in millimetres
Key
1 vision obstruction
2 high eye position
3 to horizon
4 low eye position
5 required vertical range of vision
6 lowest unobstructed line of vision
7 point of visual obstruction
8 seat compression (see 3.5)
Figure 2 — Eye positions and vertical range of vision — Helmsman in seated position
3.6
theoretical keel
〈craft without a clear intersection of bottom running surfaces at the longitudinal centreline〉 intersection of the
lowest bottom surfaces of the craft projected horizontally to the longitudinal centreplane of the craft
See Figure 3.
3.7
level reference line
real or designated waterline of the craft determined for the o
...

SLOVENSKI STANDARD
oSIST prEN ISO 11591:2008
01-marec-2008
Mala plovila na motorni pogon - Vidno polje izza krmilne mize (ISO/DIS 11591:2007)
Small craft, engine-driven - Field of vision from helm position (ISO/DIS 11591:2007)
Motorgetriebene kleine Wasserfahrzeuge - Sichtfeld vom Steuerstand (ISO/DIS
11591:2007)
Petits navires à moteur - Champ de visibilité depuis le poste de pilotage (ISO/DIS
11591:2007)
Ta slovenski standard je istoveten z: prEN ISO 11591
ICS:
47.080
oSIST prEN ISO 11591:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
DRAFT
prEN ISO 11591
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2007
ICS 47.080 Will supersede EN ISO 11591:2000
English Version
Small craft, engine-driven - Field of vision from helm position
(ISO/DIS 11591:2007)
Petits navires à moteur - Champ de visibilité depuis le
poste de pilotage (ISO/DIS 11591:2007)
This draft European Standard is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee
CEN/SS T01.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
: This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
Warning
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN ISO 11591:2007: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------
prEN ISO 11591:2007 (E)
Contents Page
Foreword.3

2

---------------------- Page: 3 ----------------------
prEN ISO 11591:2007 (E)
Foreword
This document (prEN ISO 11591:2007) has been prepared by Technical Committee ISO/TC 188 "Small craft"
in collaboration with Technical Committee CEN/SS T01 "Shipbuilding and maritime structures", the secretariat
of which is held by CMC.
This document is currently submitted to the parallel Enquiry.
This document will supersede EN ISO 11591:2000.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EC Directive(s).
Endorsement notice
The text of ISO/DIS 11591:2007 has been approved by CEN as a prEN ISO 11591:2007 without any
modification.

3

---------------------- Page: 4 ----------------------
DRAFT INTERNATIONAL STANDARD ISO/DIS 11591
ISO/TC 188 Secretariat: SIS
Voting begins on: Voting terminates on:
2007-12-06 2008-05-06
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Small craft, engine-driven — Field of vision from helm position
Petits navires à moteur — Champ de visibilité depuis le poste de pilotage
[Revision of first edition (ISO 11591:2000)]
ICS 47.080

ISO/CEN PARALLEL ENQUIRY
The CEN Secretary-General has advised the ISO Secretary-General that this ISO/DIS covers a subject
of interest to European standardization. In accordance with the ISO-lead mode of collaboration as
defined in the Vienna Agreement, consultation on this ISO/DIS has the same effect for CEN
members as would a CEN enquiry on a draft European Standard. Should this draft be accepted, a
final draft, established on the basis of comments received, will be submitted to a parallel two-month FDIS
vote in ISO and formal vote in CEN.
To expedite distribution, this document is circulated as received from the committee secretariat.
ISO Central Secretariat work of editing and text composition will be undertaken at publication
stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
©
International Organization for Standardization, 2007

---------------------- Page: 5 ----------------------
ISO/DIS 11591
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user's country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying,
recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
©
ii ISO 2007 – All rights reserved

---------------------- Page: 6 ----------------------
ISO/DIS 11591
Contents Page
Foreword .iv
1 Scope.1
2 Normative reference.1
3 Terms and definitions .1
4 General requirements .4
5 Field of vision — forward.5
5.1 Horizontal .5
5.2 Vertical.5
6 Field of horizontal vision — astern.7
7 Owner’s manual.7

© ISO 2007 – All rights reserved iii

---------------------- Page: 7 ----------------------
ISO/DIS 11591
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11591 was prepared by Technical Committee ISO/TC 188, Small craft.
This second edition cancels and replaces the first edition (ISO 11591:2000), which has been technically
revised.
iv © ISO 2007 – All rights reserved

---------------------- Page: 8 ----------------------
DRAFT INTERNATIONAL STANDARD ISO/DIS 11591

Small craft, engine-driven — Field of vision from helm position
1 Scope
This International Standard specifies requirements for the field of vision from the helm position, forward and
astern, in engine-driven small craft of up to 24 m length of hull.
The following craft are exempt from the application of this International Standard:
⎯ sailboats;
⎯ tiller-steered craft (3.7) with maximum speed less than 10 kn (10 knots).
NOTE Small engine driven craft can be operated in a manner and at certain speeds causing trim angles such that
vision forward is temporarily obscured. This International Standard cannot assure that a craft can be operated without
some temporary loss of vision from the helm position while operating at high trim angles during the transition from
displacement to planing mode.paragraph.
2 Normative reference
The following normative document contains provisions which, through reference in this text, constitute
provisions of this International Standard. For dated references, subsequent amendments to, or revisions of,
this publication do not apply. However, parties to agreements based on this International Standard are
encouraged to investigate the possibility of applying the most recent edition of the normative document
indicated below. For undated references, the latest edition of the normative document referred to applies.
Members of IEC and ISO maintain registers of currently valid International Standards.
ISO 8666, Small craft — Principal data
ISO 3538, Road vehicles — Safety glazing materials — Test methods for optical properties
3 Terms and definitions
For the purposes of this International Standard, the following terms and definitions apply.
3.1
high eye position
(1) helmsman in standing positi
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.