SIST EN ISO 2244:2003

SLOVENSKI STANDARD
SIST EN ISO 2244:2003
01-januar-2003
1DGRPHãþD
SIST EN 22244:1996
Embalaža - Celovita, napolnjena transportna embalaža - Preskus z vodoravnim
udarcem (ISO 2244:2000)
Packaging - Complete, filled transport packages and unit loads - Horizontal impact tests
(ISO 2244:2000)
Verpackung - Versandfertige Packstücke und Ladeeinheiten - Horizontale Stoßprüfung
(ISO 2244:2000)
Emballages - Emballages d'expédition complets et pleins et charges unitaires - Essais
de choc horizontal (ISO 2244:2000)
Ta slovenski standard je istoveten z: EN ISO 2244:2002
ICS:
55.180.40 Celovita, napolnjena Complete, filled transport
transportna embalaža packages
SIST EN ISO 2244:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 2244:2003

---------------------- Page: 2 ----------------------

SIST EN ISO 2244:2003
EUROPEAN STANDARD
EN ISO 2244
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2002
ICS 55.180.40 Supersedes EN 22244:1992
English version
Packaging - Complete, filled transport packages and unit loads -
Horizontal impact tests (ISO 2244:2000)
Emballages - Emballages d'expédition complets et pleins Verpackung - Versandfertige Packstücke und
et charges unitaires - Essais de choc horizontal (ISO Ladeeinheiten - Horizontale Stoßprüfung (ISO 2244:2000)
2244:2000)
This European Standard was approved by CEN on 26 August 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 2244:2002 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 2244:2003
EN ISO 2244:2002 (E)
Foreword
The text of the International Standard from Technical Committee ISO/TC 122 "Packaging" of the
International Organization for Standardization (ISO) has been taken over as a European
Standard by Technical Committee CEN/TC 261 "Packaging", the secretariat of which is held by
AFNOR.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by March 2003, and conflicting national
standards shall be withdrawn at the latest by March 2003.
This document supersedes EN 22244:1992.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,
Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of the International Standard ISO 2244:2000 has been approved by CEN as a
European Standard without any modifications.
NOTE Normative references to International Standards are listed in annex ZA (normative).
2

---------------------- Page: 4 ----------------------

SIST EN ISO 2244:2003
EN ISO 2244:2002 (E)
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 2206 1987 Packaging - Complete, filled transport EN 22206 1992
packages - Identification of parts when
testing
ISO 2233 2000 Packaging - Complete, filled transport EN ISO 2233 2001
packages and unit loads - Conditioning
for testing
3

---------------------- Page: 5 ----------------------

SIST EN ISO 2244:2003

---------------------- Page: 6 ----------------------

SIST EN ISO 2244:2003
INTERNATIONAL ISO
STANDARD 2244
Third edition
2000-03-01
Packaging — Complete, filled transport
packages and unit loads —
Horizontal impact tests
Emballages — Emballages d'expédition complets et pleins et charges
unitaires — Essais de choc horizontal
Reference number
ISO 2244:2000(E)
©
ISO 2000

---------------------- Page: 7 ----------------------

SIST EN ISO 2244:2003
ISO 2244:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading
this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in
this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 2244:2003
ISO 2244:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 2244 was prepared by Technical Committee ISO/TC 122, Packaging, Subcommittee
SC 3, Performance requirements and tests for means of packaging, packages and unit loads (as required by
ISO/TC 122).
This third edition cancels and replaces the second edition (ISO 2244:1985) which has been technically revised.
© ISO 2000 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 2244:2003
ISO 2244:2000(E)
Introduction
It is the responsibility of the user of this International Standard to establish appropriate health and safety practice in
accordance with relevant legislation.
iv © ISO 2000 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 2244:2003
INTERNATIONAL STANDARD ISO 2244:2000(E)
Packaging — Complete, filled transport packages and unit
loads — Horizontal impact tests
1 Scope
This International Standard specifies methods of horizontal impact testing (horizontal or inclined plane test and
pendulum test) on a complete, filled transport package or a unit load. The test may be performed either as a single
test to investigate the effects of horizontal impact or as part of a sequence of tests designed to measure the ability
of a package or a unit load to withstand a distribution system that includes a horizontal impact hazard.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.
ISO 2206, Packaging — Complete, filled transport packages — Identification of parts when testing.
ISO 2233, Packaging — Complete, filled transport packages and unit loads — Conditioning for testing.
3 Term and definition
For the purposes of this International Standard, the following term and definition applies.
3.1
...