Heat-treatable steels, alloy steels and free-cutting steels - Part 3: Case-hardening steels (ISO 683-3:2016)

ISO 683-3:2016 specifies the technical delivery requirements for
- semi-finished products, hot formed, e.g. blooms, billets, slabs (see Note 1),
- bars (see Note 1),
- wire rod,
- finished flat products, and
- hammer or drop forgings (see Note 1)
manufactured from the case-hardening non-alloy or alloy steels listed in Table 3 and supplied in one of the heat-treatment conditions given for the different types of products in Table 1 and in one of the surface conditions given in Table 2.
The steels are, in general, intended for the manufacture of case-hardened (see 3.1) machine parts.
NOTE 1 Hammer-forged semi-finished products (blooms, billets, slabs, etc.), seamless rolled rings and hammer-forged bars are covered under semi-finished products or bars and not under the term "hammer and drop forgings".
NOTE 2 For International Standards relating to steels complying with the requirements for the chemical composition in Table 3, however, supplied in other product forms or treatment conditions than given above or intended for special applications, and for other related International Standards, see the Bibliography.
In special cases, variations in these technical delivery requirements or additions to them can form the subject of an agreement at the time of enquiry and order (see 5.2 and Annex A).
In addition to ISO 683-3:2016, the general technical delivery requirements of ISO 404 are applicable.

Für eine Wärmebehandlung bestimmte Stähle, legierte Stähle und Automatenstähle - Teil 3: Einsatzstähle (ISO 683-3:2016)

Dieser Teil der ISO 683 legt die technischen Lieferbedingungen für
— Halbzeug, warmgeformt, zum Beispiel: Vorblöcke, Knüppel, Brammen (siehe Anmerkung 1),
— Stäbe (siehe Anmerkung 1),
— Walzdraht,
— fertige Flacherzeugnisse und
— Schmiedestücke (siehe Anmerkung 1)
fest, hergestellt aus unlegierten und legierten Einsatzstählen nach Tabelle 3, welche in einem der in Tabelle 1
für die verschiedenen Erzeugnisformen angegebenen Wärmebehandlungszustände und in einem der in
Tabelle 2 angegebenen Oberflächenausführungen geliefert werden.
Die Stähle sind im Allgemeinen zur Herstellung einsatzgehärteter Maschinenteile (siehe 3.1) vorgesehen.
ANMERKUNG 1 Freiformgeschmiedete Halbzeuge (Blöcke, Knüppel, Brammen usw.), nahtlos gewalzte Ringe und
freiformgeschmiedeter Stabstahl sind im Folgenden unter den Begriffen „Halbzeug“ und „Stabstahl“ und nicht unter dem
Begriff „Schmiedestücke“ erfasst.
ANMERKUNG 2 Bezüglich internationaler Normen für Stähle, die die chemische Zusammensetzung nach Tabelle 3
erfüllen, die jedoch in anderen Erzeugnisformen oder Wärmebehandlungszuständen als oben angegeben oder für
besondere Anwendungen geliefert werden, sowie bezüglich anderer internationaler Normen siehe die
Literaturhinweise.
In Sonderfällen können bei der Anfrage und Bestellung Abweichungen von oder Zusätze zu diesen
technischen Lieferbedingungen vereinbart werden (siehe 5.2 und Anhang A).
Zusätzlich zu diesem Teil der ISO 683 sind die allgemeinen technischen Lieferbedingungen nach ISO 404
anzuwenden.

Aciers pour traitement thermique, aciers alliés et aciers pour décolletage - Partie 3: Aciers pour cémentation (ISO 683-3:2016)

La présente partie de l'ISO 683 spécifie les conditions techniques de livraison des:
— demi-produits formés à chaud, comme par exemple les blooms, billettes et brames (voir Note 1);
— barres (voir Note 1);
— fils machine;
— produits plats finis; et
— pièces forgées par martelage ou estampage (voir Note 1)
fabriqués à partir d'aciers alliés ou non alliés pour cémentation énumérés dans le Tableau 3 et livrés dans l'un des états de traitement thermique donnés pour les différents types de produits dans le Tableau 1 et dans l'un des états de surface donnés dans le Tableau 2.
Les aciers sont en général destinés à la fabrication de pièces mécaniques cémentées (voir 3.1).
NOTE 1 Les produits semi-finis forgés par martelage (blooms, billettes, brames, etc.), les anneaux laminés sans soudure et les barres forgées par martelage figurent parmi les produits semi-finis ou les barres, et non sous l'appellation «pièces forgées par martelage ou estampage».
NOTE 2 Pour les Normes internationales relatives aux aciers qui sont conformes aux exigences de composition chimique du Tableau 3, mais fournis sous d'autres formes de produits ou dans des états de traitement autres que ceux indiqués ci-dessus, ou qui sont destinés à des applications spéciales, ainsi que pour d'autres Normes internationales analogues, voir la Bibliographie.
Dans certains cas particuliers, il est possible de déroger aux présentes conditions techniques de livraison ou d'en ajouter d'autres, à condition d'en convenir au moment de l'appel d'offres et de la commande (voir 5.2 et Annexe A).
En plus de cette partie de l'ISO 683, les conditions générales techniques de livraison de l'ISO 404 sont applicables.

Toplotno obdelana, legirana in avtomatna jekla - 3. del: Cementacijska jekla (ISO 683-3:2016)

ISO 683-3:2016 določa tehnične dobavne zahteve za
– vroče oblikovane polizdelke, npr. bloke, palice, plošče (glej opombo 1),
– drogove (glej opombo 1),
– valjane žice,
– končne ploščate izdelke in
– izkovke, kovane s padalnimi kladivi (glej opombo 1),
izdelane iz nelegiranih ali legiranih cementacijskih jekel, navedenih v preglednici 3, ter dobavljenih v enem od stanj toplotne obdelave, podanih za različne vrste izdelkov v preglednici 1, in enem od površinskih stanj, podanih v preglednici 2.
Jekla so na splošno namenjena za izdelavo cementiranih (glej točko 3.1) strojnih delov.
OPOMBA 1: S kladivom kovani polizdelki (bloki, palice, plošče itd.), nevarjeni valjani obročki in s kladivom kovani drogovi so zajeti pod polizdelki ali drogovi in ne pod izrazom »izkovki, kovani s padalnimi kladivi«.
OPOMBA 2: Za mednarodne standarde v zvezi z jekli, skladnimi z zahtevami za kemično sestavo v preglednici 3, ki pa so dobavljena v drugih oblikah izdelkov ali stanjih obdelave, kot so podani zgoraj, ali namenjena za posebne aplikacije, in za druge povezane mednarodne standarde glej bibliografijo.
V posebnih primerih so lahko različice teh splošnih tehničnih dobavnih zahtev ali dodatki k njim predmet sporazuma v času povpraševanja in naročila (glej točko 5.2 in dodatek A).
Poleg standarda ISO 683-3:2016 se uporabljajo tudi splošne tehnične dobavne zahteve standarda ISO 404.

General Information

Status
Withdrawn
Public Enquiry End Date
30-Apr-2017
Publication Date
21-Aug-2018
Withdrawal Date
20-Feb-2019
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
21-Feb-2019
Due Date
16-Mar-2019
Completion Date
21-Feb-2019

Relations

Buy Standard

Standard
EN ISO 683-3:2018
English language
44 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 683-3:2017
English language
40 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 683-3:2018
01-september-2018
1DGRPHãþD
SIST EN 10084:2008
Toplotno obdelana, legirana in avtomatna jekla - 3. del: Cementacijska jekla (ISO
683-3:2016)
Heat-treatable steels, alloy steels and free-cutting steels - Part 3: Case-hardening steels
(ISO 683-3:2016)
Für eine Wärmebehandlung bestimmte Stähle, legierte Stähle und Automatenstähle -
Teil 3: Einsatzstähle (ISO 683-3:2016)
Aciers pour traitement thermique, aciers alliés et aciers pour décolletage - Partie 3:
Aciers pour cémentation (ISO 683-3:2016)
Ta slovenski standard je istoveten z: EN ISO 683-3:2018
ICS:
77.140.10 Jekla za toplotno obdelavo Heat-treatable steels
77.140.20 Visokokakovostna jekla Stainless steels
SIST EN ISO 683-3:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 683-3:2018

---------------------- Page: 2 ----------------------

SIST EN ISO 683-3:2018


EN ISO 683-3
EUROPEAN STANDARD

NORME EUROPÉENNE

June 2018
EUROPÄISCHE NORM
ICS 77.140.10; 77.140.20 Supersedes EN 10084:2008
English Version

Heat-treatable steels, alloy steels and free-cutting steels -
Part 3: Case-hardening steels (ISO 683-3:2016)
Aciers pour traitement thermique, aciers alliés et Für eine Wärmebehandlung bestimmte Stähle, legierte
aciers pour décolletage - Partie 3: Aciers pour Stähle und Automatenstähle - Teil 3: Einsatzstähle (ISO
cémentation (ISO 683-3:2016) 683-3:2016)
This European Standard was approved by CEN on 18 May 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 683-3:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 683-3:2018
EN ISO 683-3:2018 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 683-3:2018
EN ISO 683-3:2018 (E)
European foreword
The text of ISO 683-3:2016 has been prepared by Technical Committee ISO/TC 17 “Steel” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 683-3:2018 by
Technical Committee ECISS/TC 105 “Steels for heat treatment, alloy steels, free-cutting steels and
stainless steels” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2018, and conflicting national standards
shall be withdrawn at the latest by December 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 10084:2008.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 683-3:2016 has been approved by CEN as EN ISO 683-3:2018 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 683-3:2018
EN ISO 683-3:2018 (E)
The European steel numbers to the steel grades are to be found in informative Annex B. Some European
steel numbers were not available at the publication of this International standard, for this reason they
are given now below.

Steel 22Mn6 20 Cr4 20CrS4 24CrMo4 24CrMoS4
name
Steel 1.1160 1.7027 1.7028 1.7208 1.7209
number

The references to following European standards are given for information:
EN 10017, Steels rod for drawing and/or cold rolling – Dimensions and tolerances
EN 10021, General technical delivery conditions for steel products
EN 10029, Hot-rolled steel plates 3 mm thick or above – Tolerances on dimensions and shape
EN 10048, Hot-rolled narrow steel strip – Tolerances on dimensions and shape
EN 10051, Continuously hot-rolled strip and plate/sheet cut from wide strip of non.-alloy and alloy steels –
Tolerances on dimensions and shape
EN 10058, Hot rolled flat steel bars for general purposes – Dimensions and tolerances on shape and
dimensions
EN 10059, Hot rolled square steel bars for general purposes – Dimensions and tolerances on shape and
dimensions
EN 10060, Hot rolled round steel bars - Dimensions and tolerances on shape and dimensions
EN 10061, Hot rolled hexagon steel bars – Dimensions and tolerances on shape and dimensions
EN 10160, Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection
method)
EN 10204, Metallic products – Types of inspection documents
EN 10308, Non-destructive testing – Ultrasonic testing of steel bars
4

---------------------- Page: 6 ----------------------

SIST EN ISO 683-3:2018
INTERNATIONAL ISO
STANDARD 683-3
Second edition
2016-07-15
Heat-treatable steels, alloy steels and
free-cutting steels —
Part 3:
Case-hardening steels
Aciers pour traitement thermique, aciers alliés et aciers pour
décolletage —
Partie 3: Aciers pour cémentation
Reference number
ISO 683-3:2016(E)
©
ISO 2016

---------------------- Page: 7 ----------------------

SIST EN ISO 683-3:2018
ISO 683-3:2016(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 683-3:2018
ISO 683-3:2016(E)

Contents Page
Foreword .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Classification and designation . 2
4.1 Classification . 2
4.2 Designation . 3
5 Information to be supplied by the purchaser. 3
5.1 Mandatory information . 3
5.2 Options and/or supplementary or special requirements . 3
5.3 Ordering example . 3
6 Manufacturing process . 4
6.1 General . 4
6.2 Deoxidation . 4
6.3 Heat-treatment condition and surface condition at delivery . 4
6.3.1 Normal condition at delivery . 4
6.3.2 Particular heat-treatment condition . . 4
6.3.3 Particular surface conditions . 4
6.4 Traceability of the cast . 4
7 Requirements . 4
7.1 Chemical composition, hardness and hardenability . 4
7.1.1 General. 4
7.1.2 Chemical composition . 5
7.2 Machinability . 5
7.3 Cold shearability . 5
7.4 Grain size . 5
7.5 Non-metallic inclusions . 5
7.5.1 Microscopic inclusions . 5
7.5.2 Macroscopic inclusions . 5
7.6 Internal soundness . 6
7.7 Surface condition . 6
7.8 Shape, dimensions and tolerances . 6
8 Inspection . 6
8.1 Testing procedures and types of documents . 6
8.2 Frequency of testing . 7
8.3 Tests to be carried out for specific inspection . 7
8.3.1 General. 7
8.3.2 Visual and dimensional inspection . 7
9 Test methods . 7
9.1 Chemical analysis . 7
9.2 Hardness and hardenability tests . 7
9.2.1 Verification of hardness . 7
9.2.2 Verification of hardenability . 7
9.3 Retests . 8
10 Marking . 8
Annex A (normative) Supplementary or special requirements .29
Annex B (informative) Designation of steels given in this part of ISO 683 and of comparable
grades covered in various designation systems.31
© ISO 2016 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 683-3:2018
ISO 683-3:2016(E)

Annex C (informative) Dimensional standards applicable to products complying with this
part of ISO 683 .33
Annex D (informative) Classification of steel grades according to minimum tensile strength
as a function of diameter after hardening and tempering at 200 °C .34
Bibliography .35
iv © ISO 2016 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 683-3:2018
ISO 683-3:2016(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.
The committee responsible for this document is ISO/TC 17, Steel, Subcommittee SC 4, Heat-treatable and
alloy steels.
This second edition cancels and replaces the first edition (ISO 683-3:2014), of which it constitutes a
minor revision.
ISO 683 consists of the following parts, under the general title Heat-treatable steels, alloy steels and free-
cutting steels:
— Part 1: Non-alloy steels for quenching and tempering
— Part 2: Alloy steels for quenching and tempering
— Part 3: Case-hardening steels
— Part 4: Free-cutting steels
— Part 5: Nitriding steels
— Part 14: Hot-rolled steels for quenched and tempered springs
— Part 15: Valve steels for internal combustion engines
— Part 17: Ball and roller bearing steels
— Part 18: Bright steel products
© ISO 2016 – All rights reserved v

---------------------- Page: 11 ----------------------

SIST EN ISO 683-3:2018

---------------------- Page: 12 ----------------------

SIST EN ISO 683-3:2018
INTERNATIONAL STANDARD ISO 683-3:2016(E)
Heat-treatable steels, alloy steels and free-cutting steels —
Part 3:
Case-hardening steels
1 Scope
This part of ISO 683 specifies the technical delivery requirements for
— semi-finished products, hot formed, e.g. blooms, billets, slabs (see Note 1),
— bars (see Note 1),
— wire rod,
— finished flat products, and
— hammer or drop forgings (see Note 1)
manufactured from the case-hardening non-alloy or alloy steels listed in Table 3 and supplied in one
of the heat-treatment conditions given for the different types of products in Table 1 and in one of the
surface conditions given in Table 2.
The steels are, in general, intended for the manufacture of case-hardened (see 3.1) machine parts.
NOTE 1 Hammer-forged semi-finished products (blooms, billets, slabs, etc.), seamless rolled rings and
hammer-forged bars are covered under semi-finished products or bars and not under the term “hammer and
drop forgings”.
NOTE 2 For International Standards relating to steels complying with the requirements for the chemical
composition in Table 3, however, supplied in other product forms or treatment conditions than given above or
intended for special applications, and for other related International Standards, see the Bibliography.
In special cases, variations in these technical delivery requirements or additions to them can form the
subject of an agreement at the time of enquiry and order (see 5.2 and Annex A).
In addition to this part of ISO 683, the general technical delivery requirements of ISO 404 are applicable.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable to its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 377, Steel and steel products — Location and preparation of samples and test pieces for mechanical testing
ISO 404, Steel and steel products — General technical delivery requirements
ISO 642:1999, Steel — Hardenability test by end quenching (Jominy test)
ISO 643, Steels — Micrographic determination of the apparent grain size
ISO 4885, Ferrous products — Heat treatments — Vocabulary
ISO 4948-1, Steels — Classification — Part 1: Classification of steels into unalloyed and alloy steels based
on chemical composition
© ISO 2016 – All rights reserved 1

---------------------- Page: 13 ----------------------

SIST EN ISO 683-3:2018
ISO 683-3:2016(E)

ISO 4948-2, Steels — Classification — Part 2: Classification of unalloyed and alloy steels according to main
quality classes and main property or application characteristics
ISO 4967, Steel — Determination of content of non-metallic inclusions — Micrographic method using
standard diagrams
ISO 6506-1, Metallic materials — Brinell hardness test — Part 1: Test method
ISO 6508-1, Metallic materials — Rockwell hardness test — Part 1: Test method (scales A, B, C, D, E, F, G, H,
K, N, T)
ISO 6929, Steel products — Vocabulary
ISO 7788, Steel — Surface finish of hot-rolled plates and wide flats — Delivery requirements
ISO 9443, Heat-treatable and alloy steels — Surface quality classes for hot-rolled round bars and wire
rods — Technical delivery conditions
ISO 10474, Steel and steel products — Inspection documents
ISO 14284, Steel and iron — Sampling and preparation of samples for the determination of chemical
composition
ISO/TR 9769, Steel and iron — Review of available methods of analysis
ISO/TS 4949, Steel names based on letter symbols
3 Terms and definitions
For the purposes of this document, the definitions of ISO 377, ISO 4885, ISO 4948-1, ISO 4948-2,
ISO 6929, ISO 14284 and the following apply.
NOTE For deviations from these terms and definitions, see Note 1 of the Scope and footnote a of Table 2.
3.1
case-hardening steels
structural steels with a relatively low carbon content, which are carburized or carbonitrided on their
surface and subsequently hardened
Note 1 to entry: These steels, after hardening, have a high degree of hardness in the surface zone and good
resistance to wear, while the core material is characterized principally by extreme toughness.
Note 2 to entry: Further, possibilities for heat treatment of case-hardening steels are, for example, nitrocarburizing
and nitriding.
3.2
non-alloy steel
as defined in ISO 4948-1
3.3
alloy steel
as defined in ISO 4948-1
4 Classification and designation
4.1 Classification
The classification of the relevant steel grades is according to ISO 4948-1 and ISO 4948-2. Steel grades
C10E, C10R, C15E, C15R, C16E, C16R and 22Mn6 are non-alloy special steels. All other steel grades
covered by this part of ISO 683 are alloy special steels.
2 © ISO 2016 – All rights reserved

---------------------- Page: 14 ----------------------

SIST EN ISO 683-3:2018
ISO 683-3:2016(E)

4.2 Designation
For the steel grades covered by this part of ISO 683, the steel names as given in the relevant tables are
allocated in accordance with ISO/TS 4949.
5 Information to be supplied by the purchaser
5.1 Mandatory information
The following information shall be supplied by the purchaser at the time of enquiry and order:
a) quantity to be delivered;
b) designation of the product form (slab, bloom, billet, round bar or square bar, wire rod, wide flats,
sheet, plate, strip, forging, etc.);
c) either the designation of the dimensional standard and the dimensions and tolerances selected
from this (see 7.8) or, for example, in the case of drop forgings, the designation of the drawing or
any other document covering the dimensions and tolerances required for the product;
d) a reference to this part of ISO 683, i.e. ISO 683-3;
e) the designation of the steel type given in Table 3;
f) standard designation for a test report 2.2 or, if required, any other type of inspection document in
accordance with ISO 10474 (or according to another regional standard, e.g. EN 10204 or JIS G 0415).
5.2 Options and/or supplementary or special requirements
A number of options are specified in this International Standard and listed below. If the purchaser does
not indicate the wish to implement any of these options, the products will be supplied in accordance
with the basic specifications of this part of ISO 683 (see 5.1):
a) if a heat-treatment condition other than the untreated condition is required, the symbol for this
other condition (see Table 1, column 2);
b) if a surface condition other than “hot worked” or a special surface quality is required, the surface
condition (see Table 2) and the surface quality (see 7.7.3);
c) any requirement for restricted hardenability scatter bands for alloy steels (+HH, +HL; see 7.1.1,
Table 6 and Figure 1);
d) if any supplementary requirement shall be complied with, the symbol and, where necessary, the
details of this supplementary requirement (see Annex A);
e) any requirement for the verification of non-metallic inclusion content (see 7.5);
f) verification of hardenability and, if agreed, the information about calculation of the hardenability
(see 9.2.2);
g) any requirement concerning suitability of bars and rod for bright drawing (see 7.7.4);
h) any requirement relating to removal of surface defects (see 7.7.5).
5.3 Ordering example
EXAMPLE 50 hot-rolled round bars in accordance with ISO 1035-1 with a nominal diameter of 40 mm and
a nominal length of 8 000 mm with diameter tolerance according to class S and with length tolerance according
to class L2 of ISO 1035-4 made of steel grade ISO 683-3, 20MnCr5 (see Table 3) in the heat-treatment condition
annealed (+A), surface blast cleaned (+BC) (see Table 2), product analysis/option A.3 with an inspection
certificate 3.1 in accordance with ISO 10474.
© ISO 2016 – All rights reserved 3

---------------------- Page: 15 ----------------------

SIST EN ISO 683-3:2018
ISO 683-3:2016(E)

50 Round bars ISO 1035 – 40,0S × 8 000L2
ISO 683-3 – 20MnCr5+A+BC, Option A.3
ISO 10474 – 3.1
6 Manufacturing process
6.1 General
The manufacturing process of the steel and of the products is, with the restrictions given by the
requirements in 6.2 to 6.4, left to the discretion of the manufacturer.
For minimum reduction ratio or minimum thickness deformation ratio of rolled and forged products,
see A.4.
6.2 Deoxidation
All steels shall be deoxidized.
6.3 Heat-treatment condition and surface condition at delivery
6.3.1 Normal condition at delivery
Unless otherwise agreed at the time of enquiry and order, the products shall be delivered in the
untreated condition, i.e. hot-worked condition.
6.3.2 Particular heat-treatment condition
If so agreed at the time of enquiry and order, the products shall be delivered in one of the heat-treatment
conditions given in Table 1, lines 3 to 8.
6.3.3 Particular surface conditions
If so agreed at the time of enquiry and order, the products shall be delivered in one of the particular
surface conditions given in Table 2, lines 3 to 6.
6.4 Traceability of the cast
The products shall be traceable to the cast, see Clause 10.
7 Requirements
7.1 Chemical composition, hardness and hardenability
7.1.1 G
...

SLOVENSKI STANDARD
oSIST prEN ISO 683-3:2017
01-april-2017
Toplotno obdelana, legirana in avtomatna jekla - 3. del: Cementacijska jekla (ISO
683-3:2016)
Heat-treatable steels, alloy steels and free-cutting steels - Part 3: Case-hardening steels
(ISO 683-3:2016)
Für eine Wärmebehandlung bestimmte Stähle, legierte Stähle und Automatenstähle -
Teil 3: Einsatzstähle (ISO 683-3:2016)
Aciers pour traitement thermique, aciers alliés et aciers pour décolletage - Partie 3:
Aciers pour cémentation (ISO 683-3:2016)
Ta slovenski standard je istoveten z: prEN ISO 683-3
ICS:
77.140.10 Jekla za toplotno obdelavo Heat-treatable steels
77.140.20 Visokokakovostna jekla Stainless steels
oSIST prEN ISO 683-3:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 683-3:2017

---------------------- Page: 2 ----------------------
oSIST prEN ISO 683-3:2017
INTERNATIONAL ISO
STANDARD 683-3
Second edition
2016-07-15
Heat-treatable steels, alloy steels and
free-cutting steels —
Part 3:
Case-hardening steels
Aciers pour traitement thermique, aciers alliés et aciers pour
décolletage —
Partie 3: Aciers pour cémentation
Reference number
ISO 683-3:2016(E)
©
ISO 2016

---------------------- Page: 3 ----------------------
oSIST prEN ISO 683-3:2017
ISO 683-3:2016(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 683-3:2017
ISO 683-3:2016(E)

Contents Page
Foreword .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Classification and designation . 2
4.1 Classification . 2
4.2 Designation . 3
5 Information to be supplied by the purchaser. 3
5.1 Mandatory information . 3
5.2 Options and/or supplementary or special requirements . 3
5.3 Ordering example . 3
6 Manufacturing process . 4
6.1 General . 4
6.2 Deoxidation . 4
6.3 Heat-treatment condition and surface condition at delivery . 4
6.3.1 Normal condition at delivery . 4
6.3.2 Particular heat-treatment condition . . 4
6.3.3 Particular surface conditions . 4
6.4 Traceability of the cast . 4
7 Requirements . 4
7.1 Chemical composition, hardness and hardenability . 4
7.1.1 General. 4
7.1.2 Chemical composition . 5
7.2 Machinability . 5
7.3 Cold shearability . 5
7.4 Grain size . 5
7.5 Non-metallic inclusions . 5
7.5.1 Microscopic inclusions . 5
7.5.2 Macroscopic inclusions . 5
7.6 Internal soundness . 6
7.7 Surface condition . 6
7.8 Shape, dimensions and tolerances . 6
8 Inspection . 6
8.1 Testing procedures and types of documents . 6
8.2 Frequency of testing . 7
8.3 Tests to be carried out for specific inspection . 7
8.3.1 General. 7
8.3.2 Visual and dimensional inspection . 7
9 Test methods . 7
9.1 Chemical analysis . 7
9.2 Hardness and hardenability tests . 7
9.2.1 Verification of hardness . 7
9.2.2 Verification of hardenability . 7
9.3 Retests . 8
10 Marking . 8
Annex A (normative) Supplementary or special requirements .29
Annex B (informative) Designation of steels given in this part of ISO 683 and of comparable
grades covered in various designation systems.31
© ISO 2016 – All rights reserved iii

---------------------- Page: 5 ----------------------
oSIST prEN ISO 683-3:2017
ISO 683-3:2016(E)

Annex C (informative) Dimensional standards applicable to products complying with this
part of ISO 683 .33
Annex D (informative) Classification of steel grades according to minimum tensile strength
as a function of diameter after hardening and tempering at 200 °C .34
Bibliography .35
iv © ISO 2016 – All rights reserved

---------------------- Page: 6 ----------------------
oSIST prEN ISO 683-3:2017
ISO 683-3:2016(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.
The committee responsible for this document is ISO/TC 17, Steel, Subcommittee SC 4, Heat-treatable and
alloy steels.
This second edition cancels and replaces the first edition (ISO 683-3:2014), of which it constitutes a
minor revision.
ISO 683 consists of the following parts, under the general title Heat-treatable steels, alloy steels and free-
cutting steels:
— Part 1: Non-alloy steels for quenching and tempering
— Part 2: Alloy steels for quenching and tempering
— Part 3: Case-hardening steels
— Part 4: Free-cutting steels
— Part 5: Nitriding steels
— Part 14: Hot-rolled steels for quenched and tempered springs
— Part 15: Valve steels for internal combustion engines
— Part 17: Ball and roller bearing steels
— Part 18: Bright steel products
© ISO 2016 – All rights reserved v

---------------------- Page: 7 ----------------------
oSIST prEN ISO 683-3:2017

---------------------- Page: 8 ----------------------
oSIST prEN ISO 683-3:2017
INTERNATIONAL STANDARD ISO 683-3:2016(E)
Heat-treatable steels, alloy steels and free-cutting steels —
Part 3:
Case-hardening steels
1 Scope
This part of ISO 683 specifies the technical delivery requirements for
— semi-finished products, hot formed, e.g. blooms, billets, slabs (see Note 1),
— bars (see Note 1),
— wire rod,
— finished flat products, and
— hammer or drop forgings (see Note 1)
manufactured from the case-hardening non-alloy or alloy steels listed in Table 3 and supplied in one
of the heat-treatment conditions given for the different types of products in Table 1 and in one of the
surface conditions given in Table 2.
The steels are, in general, intended for the manufacture of case-hardened (see 3.1) machine parts.
NOTE 1 Hammer-forged semi-finished products (blooms, billets, slabs, etc.), seamless rolled rings and
hammer-forged bars are covered under semi-finished products or bars and not under the term “hammer and
drop forgings”.
NOTE 2 For International Standards relating to steels complying with the requirements for the chemical
composition in Table 3, however, supplied in other product forms or treatment conditions than given above or
intended for special applications, and for other related International Standards, see the Bibliography.
In special cases, variations in these technical delivery requirements or additions to them can form the
subject of an agreement at the time of enquiry and order (see 5.2 and Annex A).
In addition to this part of ISO 683, the general technical delivery requirements of ISO 404 are applicable.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable to its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 377, Steel and steel products — Location and preparation of samples and test pieces for mechanical testing
ISO 404, Steel and steel products — General technical delivery requirements
ISO 642:1999, Steel — Hardenability test by end quenching (Jominy test)
ISO 643, Steels — Micrographic determination of the apparent grain size
ISO 4885, Ferrous products — Heat treatments — Vocabulary
ISO 4948-1, Steels — Classification — Part 1: Classification of steels into unalloyed and alloy steels based
on chemical composition
© ISO 2016 – All rights reserved 1

---------------------- Page: 9 ----------------------
oSIST prEN ISO 683-3:2017
ISO 683-3:2016(E)

ISO 4948-2, Steels — Classification — Part 2: Classification of unalloyed and alloy steels according to main
quality classes and main property or application characteristics
ISO 4967, Steel — Determination of content of non-metallic inclusions — Micrographic method using
standard diagrams
ISO 6506-1, Metallic materials — Brinell hardness test — Part 1: Test method
ISO 6508-1, Metallic materials — Rockwell hardness test — Part 1: Test method (scales A, B, C, D, E, F, G, H,
K, N, T)
ISO 6929, Steel products — Vocabulary
ISO 7788, Steel — Surface finish of hot-rolled plates and wide flats — Delivery requirements
ISO 9443, Heat-treatable and alloy steels — Surface quality classes for hot-rolled round bars and wire
rods — Technical delivery conditions
ISO 10474, Steel and steel products — Inspection documents
ISO 14284, Steel and iron — Sampling and preparation of samples for the determination of chemical
composition
ISO/TR 9769, Steel and iron — Review of available methods of analysis
ISO/TS 4949, Steel names based on letter symbols
3 Terms and definitions
For the purposes of this document, the definitions of ISO 377, ISO 4885, ISO 4948-1, ISO 4948-2,
ISO 6929, ISO 14284 and the following apply.
NOTE For deviations from these terms and definitions, see Note 1 of the Scope and footnote a of Table 2.
3.1
case-hardening steels
structural steels with a relatively low carbon content, which are carburized or carbonitrided on their
surface and subsequently hardened
Note 1 to entry: These steels, after hardening, have a high degree of hardness in the surface zone and good
resistance to wear, while the core material is characterized principally by extreme toughness.
Note 2 to entry: Further, possibilities for heat treatment of case-hardening steels are, for example, nitrocarburizing
and nitriding.
3.2
non-alloy steel
as defined in ISO 4948-1
3.3
alloy steel
as defined in ISO 4948-1
4 Classification and designation
4.1 Classification
The classification of the relevant steel grades is according to ISO 4948-1 and ISO 4948-2. Steel grades
C10E, C10R, C15E, C15R, C16E, C16R and 22Mn6 are non-alloy special steels. All other steel grades
covered by this part of ISO 683 are alloy special steels.
2 © ISO 2016 – All rights reserved

---------------------- Page: 10 ----------------------
oSIST prEN ISO 683-3:2017
ISO 683-3:2016(E)

4.2 Designation
For the steel grades covered by this part of ISO 683, the steel names as given in the relevant tables are
allocated in accordance with ISO/TS 4949.
5 Information to be supplied by the purchaser
5.1 Mandatory information
The following information shall be supplied by the purchaser at the time of enquiry and order:
a) quantity to be delivered;
b) designation of the product form (slab, bloom, billet, round bar or square bar, wire rod, wide flats,
sheet, plate, strip, forging, etc.);
c) either the designation of the dimensional standard and the dimensions and tolerances selected
from this (see 7.8) or, for example, in the case of drop forgings, the designation of the drawing or
any other document covering the dimensions and tolerances required for the product;
d) a reference to this part of ISO 683, i.e. ISO 683-3;
e) the designation of the steel type given in Table 3;
f) standard designation for a test report 2.2 or, if required, any other type of inspection document in
accordance with ISO 10474 (or according to another regional standard, e.g. EN 10204 or JIS G 0415).
5.2 Options and/or supplementary or special requirements
A number of options are specified in this International Standard and listed below. If the purchaser does
not indicate the wish to implement any of these options, the products will be supplied in accordance
with the basic specifications of this part of ISO 683 (see 5.1):
a) if a heat-treatment condition other than the untreated condition is required, the symbol for this
other condition (see Table 1, column 2);
b) if a surface condition other than “hot worked” or a special surface quality is required, the surface
condition (see Table 2) and the surface quality (see 7.7.3);
c) any requirement for restricted hardenability scatter bands for alloy steels (+HH, +HL; see 7.1.1,
Table 6 and Figure 1);
d) if any supplementary requirement shall be complied with, the symbol and, where necessary, the
details of this supplementary requirement (see Annex A);
e) any requirement for the verification of non-metallic inclusion content (see 7.5);
f) verification of hardenability and, if agreed, the information about calculation of the hardenability
(see 9.2.2);
g) any requirement concerning suitability of bars and rod for bright drawing (see 7.7.4);
h) any requirement relating to removal of surface defects (see 7.7.5).
5.3 Ordering example
EXAMPLE 50 hot-rolled round bars in accordance with ISO 1035-1 with a nominal diameter of 40 mm and
a nominal length of 8 000 mm with diameter tolerance according to class S and with length tolerance according
to class L2 of ISO 1035-4 made of steel grade ISO 683-3, 20MnCr5 (see Table 3) in the heat-treatment condition
annealed (+A), surface blast cleaned (+BC) (see Table 2), product analysis/option A.3 with an inspection
certificate 3.1 in accordance with ISO 10474.
© ISO 2016 – All rights reserved 3

---------------------- Page: 11 ----------------------
oSIST prEN ISO 683-3:2017
ISO 683-3:2016(E)

50 Round bars ISO 1035 – 40,0S × 8 000L2
ISO 683-3 – 20MnCr5+A+BC, Option A.3
ISO 10474 – 3.1
6 Manufacturing process
6.1 General
The manufacturing process of the steel and of the products is, with the restrictions given by the
requirements in 6.2 to 6.4, left to the discretion of the manufacturer.
For minimum reduction ratio or minimum thickness deformation ratio of rolled and forged products,
see A.4.
6.2 Deoxidation
All steels shall be deoxidized.
6.3 Heat-treatment condition and surface condition at delivery
6.3.1 Normal condition at delivery
Unless otherwise agreed at the time of enquiry and order, the products shall be delivered in the
untreated condition, i.e. hot-worked condition.
6.3.2 Particular heat-treatment condition
If so agreed at the time of enquiry and order, the products shall be delivered in one of the heat-treatment
conditions given in Table 1, lines 3 to 8.
6.3.3 Particular surface conditions
If so agreed at the time of enquiry and order, the products shall be delivered in one of the particular
surface conditions given in Table 2, lines 3 to 6.
6.4 Traceability of the cast
The products shall be traceable to the cast, see Clause 10.
7 Requirements
7.1 Chemical composition, hardness and hardenability
7.1.1 General
Table 1 gives a survey on combinations of usual heat-treatment conditions at delivery, product forms
and requirements as specified in Tables 3 to 7 (chemical composition, hardenability, maximum hardness
and hardness range).
Unless otherwise agreed for alloy steels, the hardenability requirements given in Table 5 apply. If
agreed at the time of enquiry and order, alloy steels with restricted hardenability scatter bands given
in Table 6 or shown in Figure 1 shall be supplied.
4 © ISO 2016 – All rights reserved

---------------------- Page: 12 ----------------------
oSIST prEN ISO 683-3:2017
ISO 683-3:2016(E)

7.1.2 Chemical composition
The chemical composition determined by cast analysis shall comply with the values in Table 3.
Permissible deviations between the limiting values for cast analysis and the values for product analysis
are given in Table 4.
The product analysis shall be carried out when specified, at the time of the enquiry and order (see A.3).
7.2 Machinability
All steels are machinable in the conditions “soft-annealed”, “treated to hardness range”, “treated to
ferrite/pearlite structure” and “normalized.
Where improved machinability is required, the grades with a specified sulfur range should be ordered
and/or with a specific treatment to improve machinability (see also Table 3, footnote c).
7.3 Cold shearability
7.3.1 Under suitable shearing conditions (avoiding local stress peaks, preheating, application of blades
with a profile adapted to that of the product, etc.), all steels are cold shearable in the condition “soft-
annealed”.
7.3.2 Steel grades 28Cr4, 28CrS4, 20MnCr5, 20MnCrS5, 24CrMo4, 24CrMoS4, 22CrMoS3-5, 20MoCr4,
20MoCrS4, 16NiCr4, 16NiCrS4, 18NiCr5-4, 17CrNi6-6, 15NiCr13, 17NiCrMo6-4 and 18CrNiMo7-6, are,
under suitable conditions, also cold shearable when delivered in the condition “treated to improve
shearability” with the hardness requirements given in Table 7.
7.3.3 The non-alloy steels and steels 17Cr3, 17CrS3, 20Cr4, 20CrS4, 16MnCr5, 16MnCrS5, 16MnCrB5,
18CrMo4, 18CrMoS4, 20NiCrMo2-2 and 20NiCrMoS2-2 are, under suitable conditions, cold shearable
when delivered in the untreated condition.
7.4 Grain size
Unless otherwise agreed at the time of enquiry and order, the steel shall show a fine grain structure
with an austenitic grain size of 5 and finer, when tested in accordance with ISO 643. For verification,
see A.1.
7.5 Non-metallic inclusions
7.5.1 Microscopic inclusions
The special steels shall have a certain degree of cleanness, however, verification of the non-metallic
inclusion content requires a special agreement. If there is such an agreement at the time of enquiry
and order, the microscopic non-metallic inclusion content shall be determined to an agreed procedure
and within agreed limits in accordance with ISO 4967 or another standard, e.g. regional standards
EN 10247 or JIS G 0555.
For grades with specified minimum sulfur content, the agreement should not include sulphides.
7.5.2 Macroscopic inclusions
This requirement is applicable to the verification of the macroscopic inclusions in special steels. If
verification is agreed, the method and acceptance limits shall be agreed at the time of enquiry and order.
© ISO 2016 – All rights reserved 5

---------------------- Page: 13 ----------------------
oSIST prEN ISO 683-3:2017
ISO 683-3:2016(E)

7.6 Internal soundness
Where appropriate, requirements relating to the internal soundness of the products shall be agreed at
the time of inquiry and order (see A.2).
7.7 Surface condition
7.7.1 All products shall have a smooth surface finish appropriate to the manufacturing processes
applied.
7.7.2 Minor surface imperfections which may occur under normal manufacturing conditions, such as
prints originating from rolled-in scale, are not to be regarded as defects.
7.7.3 Bars and wire rod are delivered with surface class 1za2 according to ISO 9443 and hot-rolled
plates and wide flats shall be delivered with a surface according to ISO 7788, unless otherwise agreed at
the time of enquiry and order.
Where no International Standard on the surface quality of steel products exists, detailed requirements
referring to this characteristic shall, where appropriate, be agreed at the time of enquiry and order.
It is more difficult to detect and eliminate surface discontinuities from coiled products than from cut
lengths. This should be taken into account when agreements on surface quality are made.
NOTE Bars and wire rod for cold heading and cold extrusion are covered fully by ISO 4954.
7.7.4 If suitability of bars and rod for bright drawing is required, this shall be agreed at the time of
enquiry and order.
7.7.5 Removal of surface discontinuities by welding shall only be permitted with the approval of the
customer or his/her representative. If surface discontinuities are repaired, the method and maximum
depth of removal shall be agreed at the time of enquiry and order.
7.8 Shape, dimensions and tolerances
The nominal dimensions, tolerances on dimensions and shape of the product shall be agreed at the time
of enquiry and order, if possible, with reference to the dimensional standards applicable (see Annex C).
8 Inspection
8.1 Testing procedures and types of documents
8.1.1 Products complying with this part of ISO 683 shall be ordered and delivered with one of the
inspection documents as specified in ISO 10474 or another standard, e.g. regional standards EN 10204
or JIS G 0415. The type of document shall be agreed upon at the time of enquiry and order. If the order
does not contain any specification of this type, a test report shall be issued.
8.1.2 If, in accorda
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.