SIST EN ISO 7840:2014

SLOVENSKI STANDARD
SIST EN ISO 7840:2014
01-januar-2014
1DGRPHãþD
SIST EN ISO 7840:2004
Mala plovila - Proti ognju odporne cevi za gorivo (ISO 7840:2013)
Small craft - Fire-resistant fuel hoses (ISO 7840:2013)
Kleine Wasserfahrzeuge - Feuerwiderstandsfähige Kraftstoffschläuche (ISO 7840:2013)
Petits navires - Tuyaux souples pour carburant résistants au feu (ISO 7840:2013)
Ta slovenski standard je istoveten z: EN ISO 7840:2013
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
47.020.30 Sistemi cevi Piping systems
47.080 ýROQL Small craft
SIST EN ISO 7840:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 7840:2014

---------------------- Page: 2 ----------------------

SIST EN ISO 7840:2014


EUROPEAN STANDARD
EN ISO 7840

NORME EUROPÉENNE

EUROPÄISCHE NORM
July 2013
ICS 47.080 Supersedes EN ISO 7840:2004
English Version
Small craft - Fire-resistant fuel hoses (ISO 7840:2013)
Petits navires - Tuyaux souples pour carburant résistants Kleine Wasserfahrzeuge - Feuerwiderstandsfähige
au feu (ISO 7840:2013) Kraftstoffschläuche (ISO 7840:2013)
This European Standard was approved by CEN on 8 June 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 7840:2013: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 7840:2014
EN ISO 7840:2013 (E)
Contents Page
Foreword .3
Annex ZA (informative) Relationship between this Standard and the Essential Requirements of
EU Directive 94/25/EC as amended by Directive 2003/44/EC .4

2

---------------------- Page: 4 ----------------------

SIST EN ISO 7840:2014
EN ISO 7840:2013 (E)
Foreword
This document (EN ISO 7840:2013) has been prepared by Technical Committee ISO/TC 188 “Small craft”.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2014, and conflicting national standards shall be withdrawn at
the latest by January 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 7840:2004.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 7840:2013 has been approved by CEN as EN ISO 7840:2013 without any modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 7840:2014
EN ISO 7840:2013 (E)
Annex ZA
(informative)

Relationship between this Standard and the Essential Requirements of
EU Directive 94/25/EC as amended by Directive 2003/44/EC
By agreement between ISO and CEN, this CEN annex is included in the DIS and the FDIS but will not appear
in the published ISO standard.
This Standard has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association to provide a means of conforming to Essential Requirements of the New
Approach Directive 94/25 EC as amended by Directive 2003/44/EC.
Once this standard is cited in the Official Journal of the European Union under that Directive and has been
implemented as a national standard in at least one Member State, compliance with the normative clauses of
this standard given in Table ZA.1 confers, within the limits of the scope of this standard, a presumption of
conformity with the corresponding Essential Requirements of that Directive and associated EFTA regulations.

Table ZA.1 — Correspondence between this Standard and EU Directive 94/25/EC
as amended by Directive 2003/44/EC
Clause(s)/sub-clause(s) of this Essential Requirements (ERs) Qualifying remarks/Notes
standard of EU Directive 94/25/EC as
amended by Directive
2003/44/EC
All clauses Annex I A, Clause 5.1.1, Inboard This standard is relevant in
Engine respect of fuel filling lines and
fuel vent lines installed both
Annex I A, Clause 5.2.1, Fuel
inside and outside the engine
system, General
compartment.
Annex I A, Clause 5.6.1, Fire
It does not apply to hoses
protection, General
installed entirely within the
Annex II, Components, 4 splash well and connected
directly to an outboard engine.

WARNING: Other requirements and other EU Directives may be applicable to the product(s) falling within the
scope of this standard.
4

---------------------- Page: 6 ----------------------

SIST EN ISO 7840:2014
INTERNATIONAL ISO
STANDARD 7840
Fourth edition
2013-07-15
Small craft — Fire-resistant fuel hoses
Petits navires — Tuyaux souples pour carburant résistants au feu
Reference number
ISO 7840:2013(E)
©
ISO 2013

---------------------- Page: 7 ----------------------

SIST EN ISO 7840:2014
ISO 7840:2013(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 7840:2014
ISO 7840:2013(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 General requirements . 1
4 Nominal bore . 1
5 Physical tests on finished hose . 2
5.1 General . 2
5.2 Test liquids. 2
5.3 Bursting pressure . 2
5.4 Vacuum-collapse test . 3
5.5 Volume change in test liquids. 3
5.6 Mass reduction of test hose. 3
5.7 Fire resistance . 3
5.8 Effect of ozone . 3
5.9 Fuel permeation . 3
5.10 Cold-flex test . 4
5.11 Abrasion test — 38 mm and larger fuel-fill hose with helical wire
embedded reinforcement . 4
5.12 Dry heat resistance . 4
5.13 Oil resistance test . 4
5.14 Adhesion test . 4
6 Marking . 4
Annex A (normative) Fire test . 6
Annex B (normative) Fuel permeation test (or equivalent test method) . 8
Bibliography .10
© ISO 2013 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 7840:2014
ISO 7840:2013(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
The committee responsible for this document is ISO/TC 188, Small craft.
This fourth edition cancels and replaces the third edition (ISO 7840:2004), which has been technically
revised, mainly concerning test liquids in 5.2 to cover hoses’ long-term resistance to petrol fuel mixed
with ethanol as well as diesel fuel mixed with Fatty Acid Methyl Esters (FAME).
iv © ISO 2013 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 7840:2014
INTERNATIONAL STANDARD ISO 7840:2013(E)
Small craft — Fire-resistant fuel hoses
1 Scope
This International Standard specifies general requirements and physical tests for fire-resistant hoses
for conveying petrol or petrol blended with ethanol and diesel fuel or diesel fuel blended with FAME,
designed for a working pressure not exceeding 0,34 MPa for hoses with nominal bore up to and i
...