Welding and allied processes - Welding positions (ISO 6947:2019)

This document defines welding positions for testing and production, for butt and fillet welds, in all product forms. Annex A gives examples of the limits of the slope of a weld axis and the rotation of the weld face about the weld axis for welding positions in production welds. Annex B gives a comparison of this document and US designation systems for welding positions.

Schweißen und verwandte Prozesse - Schweißpositionen (ISO 6947:2019)

Dieses Dokument legt Schweißpositionen für das Prüfen und die Fertigung von Stumpf- und Kehlnähten in allen Produktformen fest.
Anhang A enthält Beispiele über die Grenzen der Neigung einer Schweißnahtachse und der Drehung der Schweißnahtoberfläche um die Schweißnahtachse für Schweißpositionen bei Fertigungsschweißungen.
Anhang B enthält einen Vergleich zwischen diesem Dokument und US-amerikanischen Benennungssystemen für Schweißpositionen.

Soudage et techniques connexes - Positions de soudage (ISO 6947:2019)

Le présent document définit des positions de soudage pour les essais et la production, pour les soudures bout à bout et les soudures en angle, pour toutes les formes de produit.
L'Annexe A donne des exemples de limites d'inclinaison de l'axe de la soudure et de limites de rotation de la face endroit de la soudure de part et d'autre de l'axe de la soudure, pour les différentes positions de soudage en production.
L'Annexe B donne une comparaison du système de désignation des positions de soudage selon le présent document et celui des États-Unis.

Varjenje in sorodni postopki - Položaji pri varjenju (ISO 6947:2019)

Ta dokument določa položaje varjenja za preskušanje in proizvodnjo, za soležne in kotne zvare, v vseh oblikah izdelkov. V dodatku A so podani primeri za omejitve naklona osi varjenja in vrtenja varilne ploskve okoli osi varjenja za položaje varjenja pri proizvodnih zvarih. V dodatku B je podana primerjava tega dokumenta s sistemi označevanja za položaje varjenja v ZDA.

General Information

Status
Published
Public Enquiry End Date
19-Jun-2018
Publication Date
04-Feb-2020
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
04-Dec-2019
Due Date
08-Feb-2020
Completion Date
05-Feb-2020

Relations

Buy Standard

Standard
EN ISO 6947:2020
English language
27 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 6947:2018
English language
23 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 6947:2020
01-marec-2020
Nadomešča:
SIST EN ISO 6947:2012
Varjenje in sorodni postopki - Položaji pri varjenju (ISO 6947:2019)
Welding and allied processes - Welding positions (ISO 6947:2019)
Schweißen und verwandte Prozesse - Schweißpositionen (ISO 6947:2019)
Soudage et techniques connexes - Positions de soudage (ISO 6947:2019)
Ta slovenski standard je istoveten z: EN ISO 6947:2019
ICS:
25.160.40 Varjeni spoji in vari Welded joints and welds
SIST EN ISO 6947:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 6947:2020

---------------------- Page: 2 ----------------------
SIST EN ISO 6947:2020


EN ISO 6947
EUROPEAN STANDARD

NORME EUROPÉENNE

October 2019
EUROPÄISCHE NORM
ICS 25.160.40 Supersedes EN ISO 6947:2011
English Version

Welding and allied processes - Welding positions (ISO
6947:2019)
Soudage et techniques connexes - Positions de soudage Schweißen und verwandte Prozesse -
(ISO 6947:2019) Schweißpositionen (ISO 6947:2019)
This European Standard was approved by CEN on 14 October 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6947:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 6947:2020
EN ISO 6947:2019 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 6947:2020
EN ISO 6947:2019 (E)
European foreword
This document (EN ISO 6947:2019) has been prepared by Technical Committee ISO/TC 44 "Welding
and allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2020, and conflicting national standards shall be
withdrawn at the latest by April 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 6947:2011.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 6947:2019 has been approved by CEN as EN ISO 6947:2019 without any modification.


3

---------------------- Page: 5 ----------------------
SIST EN ISO 6947:2020

---------------------- Page: 6 ----------------------
SIST EN ISO 6947:2020
INTERNATIONAL ISO
STANDARD 6947
Fourth edition
2019-10
Welding and allied processes —
Welding positions
Soudage et techniques connexes — Positions de soudage
Reference number
ISO 6947:2019(E)
©
ISO 2019

---------------------- Page: 7 ----------------------
SIST EN ISO 6947:2020
ISO 6947:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 8 ----------------------
SIST EN ISO 6947:2020
ISO 6947:2019(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Welding positions . 2
4.1 Main welding positions . 2
4.2 Welding positions and allowable deviations for testing . 5
4.3 Welding positions and ranges in production . 5
5 Designation . 6
Annex A (informative) Limits of the slope of a weld axis and the rotation of the weld face
about the weld axis for welding positions in production welds .8
Annex B (informative) Comparison of this document and US designation systems for
welding positions .15
Bibliography .19
© ISO 2019 – All rights reserved iii

---------------------- Page: 9 ----------------------
SIST EN ISO 6947:2020
ISO 6947:2019(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes,
Subcommittee SC 7, Representation and terms.
This fourth edition cancels and replaces the third edition (ISO 6947:2011), which has been technically
revised. The main changes compared to the previous edition are as follows:
— Figure 1 and Figure 2 have been revised;
— the concept of a special test position which is not covered by defined test positions has been
introduced;
— editorial corrections/improvements have been made.
Any feedback or questions on this document should be directed to the user’s national standards
body. A complete listing of these bodies can be found at www .iso .org/members .html. Official
interpretations of TC 44 documents, where they exist, are available from this page: https: //committee
.iso .org/sites/tc44/home/interpretation .html.
iv © ISO 2019 – All rights reserved

---------------------- Page: 10 ----------------------
SIST EN ISO 6947:2020
ISO 6947:2019(E)

Introduction
This document specifies positions for standard discrete test piece orientation, e.g. PA, PB, H-L045, that
have been included in this document since the third edition (ISO 6947:2011).
Since the third edition was published, positions for production welding are also defined. These
positions are flat, horizontal, vertical, and overhead. Unlike discrete testing positions, these positions
are contiguous.
Welding position are not dependent on the geometrical arrangement of the joint, e.g. butt or fillet joint,
or that of the semi-finished product. Welds of all types and in all directions are covered.
The direction of welding (i.e. upwards or downwards) can also contribute to defining welding positions.
The main positions have been given symbols which can easily be used for designation purposes; these
symbols were not derived from any particular language.
The concept of a special test position, not covered by the existing and well-defined positions, has been
included so that testing can be carried out in positions that do not meet the standard requirements.
The relationship between testing positions and production welding positions is specified elsewhere,
e.g. in the ISO 9606 series or ISO 15614 series.
© ISO 2019 – All rights reserved v

---------------------- Page: 11 ----------------------
SIST EN ISO 6947:2020

---------------------- Page: 12 ----------------------
SIST EN ISO 6947:2020
INTERNATIONAL STANDARD ISO 6947:2019(E)
Welding and allied processes — Welding positions
1 Scope
This document defines welding positions for testing and production, for butt and fillet welds, in all
product forms.
Annex A gives examples of the limits of the slope of a weld axis and the rotation of the weld face about
the weld axis for welding positions in production welds.
Annex B gives a comparison of this document and US designation systems for welding positions
...

SLOVENSKI STANDARD
oSIST prEN ISO 6947:2018
01-junij-2018
Varjenje in sorodni postopki - Položaji pri varjenju (ISO/DIS 6947:2018)
Welding and allied processes - Welding positions (ISO/DIS 6947:2018)
Schweißen und verwandte Prozesse - Schweißpositionen (ISO/DIS 6947:2018)
Soudage et techniques connexes - Positions de soudage (ISO/DIS 6947:2018)
Ta slovenski standard je istoveten z: prEN ISO 6947
ICS:
25.160.40 Varjeni spoji in vari Welded joints and welds
oSIST prEN ISO 6947:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 6947:2018

---------------------- Page: 2 ----------------------
oSIST prEN ISO 6947:2018
DRAFT INTERNATIONAL STANDARD
ISO/DIS 6947
ISO/TC 44/SC 7 Secretariat: BSI
Voting begins on: Voting terminates on:
2018-04-05 2018-06-28
Welding and allied processes — Welding positions
Soudage et techniques connexes — Positions de soudage
ICS: 25.160.40
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 6947:2018(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2018

---------------------- Page: 3 ----------------------
oSIST prEN ISO 6947:2018
ISO/DIS 6947:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 6947:2018
ISO/DIS 6947:2018(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Welding positions . 2
4.1 Main welding positions . 2
4.2 Welding positions and allowable deviations for testing . 5
4.3 Welding positions and ranges in production . 5
5 Designation . 6
Annex A (informative) Limits of the slope of a weld axis and the rotation of the weld face
about the weld axis for welding positions in production welds x title e.g. Example of
a figure and a table . 8
Annex B (informative) Comparison of international, European and US designations .14
Bibliography .18
© ISO 2018 – All rights reserved iii

---------------------- Page: 5 ----------------------
oSIST prEN ISO 6947:2018
ISO/DIS 6947:2018(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.
The committee responsible for this document is Technical Committee ISO/TC 44, Welding and allied
processes, Subcommittee SC 7, Representation and terms.
This fourth edition cancels and replaces the third edition (ISO 6947:2011), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— Figure 1 has been revised
— Introduction of the concept of a special test position which is not covered by those defined
— Editorial corrections/improvements
Requests for official interpretations of any aspect of this document should be directed to the Secretariat
of ISO/TC 44/SC 7 via your national standards body. A complete listing of these bodies can be found at
www .iso .org.
iv © ISO 2018 – All rights reserved

---------------------- Page: 6 ----------------------
oSIST prEN ISO 6947:2018
ISO/DIS 6947:2018(E)

Introduction
This document specifies positions for standard discrete test piece orientation PA, PB, H-L045, etc. that
have been included in this document since the third edition (ISO 6947:2011).
Since the third edition was published, positions for production welding are also defined. These
positions are flat, horizontal, vertical, and overhead. Unlike discrete testing positions, these positions
are contiguous.
Welding position is not dependent on the geometrical arrangement of the joint, e.g. butt or fillet joint, or
that of the semi-finished product. Welds of all types and in all directions are covered.
The direction of welding (i.e., upwards or downwards) may also contribute to defining welding
positions.
The main positions have been given symbols which can easily be used for designation purposes; these
symbols were chosen independently of possible meaningful abbreviations, i.e. they are not derived
from any particular language.
The concept of a special test position, not covered by the existing and well defined positions, has been
included so that testing can be carried out in positions that don’t meet the standard requirements.
The relationship between testing positions and production welding positions is specified elsewhere,
e.g. in ISO 9606 or ISO 15614.
© ISO 2018 – All rights reserved v

---------------------- Page: 7 ----------------------
oSIST prEN ISO 6947:2018

---------------------- Page: 8 ----------------------
oSIST prEN ISO 6947:2018
DRAFT INTERNATIONAL STANDARD ISO/DIS 6947:2018(E)
Welding and allied processes — Welding positions
1 Scope
This document defines welding positions for testing and production, for butt and fillet welds, in all
product forms.
Annex A gives examples of the limits of the slope of a weld axis and the rotation of the weld face about
the weld axis for welding positions in production welds.
Annex B gives a comparison of International, European and US designations for welding positions.
2 Normative references
There are no normative references in this document.
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http:// www .electropedia .org/
— ISO Online browsing platform: available at http:// www .iso .org/ obp
3.1
welding position
position of a weld defined relative to the slope of the axis and rotation of the face of the weld relative to
the horizontal plane
3.2
main welding position
welding position, designated PA, PB, PC, PD, PE, PF, PG and PH, PJ or PK for welding pipe (see Figures
1 and 2)
3.3
special test position
SP
any welding position that is not
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.