SIST EN IEC 60352-3:2020

SLOVENSKI STANDARD
SIST EN IEC 60352-3:2020
01-september-2020
Nadomešča:
SIST EN 60352-3:2002
Nespajkani spoji - 3. del: Dostopni izolacijsko prebodni spoji - Splošne zahteve,
preskusne metode in praktični napotki (IEC 60352-3:2020)
Solderless connections - Part 3: Accessible insulation displacement (ID) connections -
General requirements, test methods and practical guidance (IEC 60352-3:2020)
Lötfreie elektrische Verbindungen - Teil 3: Lötfreie zugängliche
Schneidklemmverbindungen - Allgemeine Anforderungen, Prüfverfahren und
Anwendungshinweise (IEC 60352-3:2020)
Connexions sans soudure - Partie 3: Connexions autodénudantes accessibles sans
soudure - Règles générales, méthodes d'essai et guide pratique (IEC 60352-3:2020)
Ta slovenski standard je istoveten z: EN IEC 60352-3:2020
ICS:
29.120.20 Spojni elementi Connecting devices
SIST EN IEC 60352-3:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 60352-3:2020

---------------------- Page: 2 ----------------------
SIST EN IEC 60352-3:2020


EUROPEAN STANDARD EN IEC 60352-3

NORME EUROPÉENNE

EUROPÄISCHE NORM
May 2020
ICS 29.120.20 Supersedes EN 60352-3:1994 and all of its amendments
and corrigenda (if any)
English Version
Solderless connections - Part 3: Accessible insulation
displacement (ID) connections - General requirements, test
methods and practical guidance
(IEC 60352-3:2020)
Connexions sans soudure - Partie 3: Connexions Lötfreie elektrische Verbindungen - Teil 3: Lötfreie
autodénudantes accessibles sans soudure - Règles zugängliche Schneidklemmverbindungen - Allgemeine
générales, méthodes d'essai et guide pratique Anforderungen, Prüfverfahren und Anwendungshinweise
(IEC 60352-3:2020) (IEC 60352-3:2020)
This European Standard was approved by CENELEC on 2020-05-14. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 60352-3:2020 E

---------------------- Page: 3 ----------------------
SIST EN IEC 60352-3:2020
EN IEC 60352-3:2020 (E)
European foreword
The text of document 48B/2789/FDIS, future edition 2 of IEC 60352-3, prepared by SC 48B "Electrical
connectors" of IEC/TC 48 "Electrical connectors and mechanical structures for electrical and electronic
equipment" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN IEC 60352-3:2020.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-02-14
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-05-14
document have to be withdrawn

This document supersedes EN 60352-3:1994 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 60352-3:2020 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60352-4 NOTE Harmonized as EN 60352-4
IEC 61984 NOTE Harmonized as EN 61984


2

---------------------- Page: 4 ----------------------
SIST EN IEC 60352-3:2020
EN IEC 60352-3:2020 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60068-1 - Environmental testing - Part 1: General and EN 60068-1 -
guidance
IEC 60228 - Conductors of insulated cables EN 60228 -
IEC 60512-1 - Conductors of insulated cables EN IEC 60512-1 -
IEC 60512-1-1 - Connectors for electronic equipment - EN 60512-1-1 -
Tests and measurements - Part 1-1:
General examination - Test 1a: Visual
examination
IEC 60512-1-2 - Connectors for electronic equipment - EN 60512-1-2 -
Tests and measurements - Part 1-2:
General examination - Test 1b:
Examination of dimension and mass
IEC 60512-2-1 - Connectors for electronic equipment - EN 60512-2-1 -
Tests and measurements - Part 2-1:
Electrical continuity and contact resistance
tests - Test 2a: Contact resistance -
Millivolt level method
IEC 60512-2-2 - Connectors for electronic equipment - EN 60512-2-2 -
Tests and measurements - Part 2-2:
Electrical continuity and contact resistance
tests - Test 2b: Contact resistance -
Specified test current method
IEC 60512-2-5 - Connectors for electronic equipment - EN 60512-2-5 -
Tests and measurements - Part 2-5:
Electrical continuity and contact resistance
tests - Test 2e: Contact disturbance
3

---------------------- Page: 5 ----------------------
SIST EN IEC 60352-3:2020
EN IEC 60352-3:2020 (E)
IEC 60512-6-4 - Connectors for electronic equipment - EN 60512-6-4 -
Tests and measurements - Part 6-4:
Dynamic stress tests - Test 6d: Vibration
(sinusoidal)
IEC 60512-9-2 - Connectors for electronic equipment - EN 60512-9-2 -
Tests and measurements - Part 9-2:
Endurance tests - Test 9b: Electrical load
and temperature
IEC 60512-11-1 - Connectors for electrical and electronic EN IEC 60512-11-1 -
equipment - Tests and measurements -
Part 11-1: Climatic tests - Test 11a -
Climatic sequence
IEC 60512-11-4 - Connectors for electronic equipment - EN 60512-11-4 -
Tests and measurements - Part 11-4:
Climatic tests - Test 11d: Rapid change of
temperature
IEC 60512-11-7 - Connectors for electronic equipment - EN 60512-11-7 -
Tests and measurements - Part 11-7:
Climatic tests - Test 11g: Flowing mixed
gas corrosion test
IEC 60512-11-9 - Connectors for electronic equipment - EN 60512-11-9 -
Tests and measurements - Part 11-9:
Climatic tests - Test 11i: Dry heat
IEC 60512-11-10 - Connectors for electronic equipment - EN 60512-11-10 -
Tests and measurements - Part 11-10:
Climatic tests - Test 11j: Cold
IEC 60512-11-12 - Connectors for electronic equipment - EN 60512-11-12 -
Tests and measurements - Part 11-12:
Climatic tests - Test 11m: Damp heat,
cyclic

4

---------------------- Page: 6 ----------------------
SIST EN IEC 60352-3:2020



IEC 60352-3

®


Edition 2.0 2020-04




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Solderless connections –

Part 3: Accessible insulation displacement (ID) connections – General

requirements, test methods and practical guidance




Connexions sans soudure –

Partie 3: Connexions autodénudantes accessibles – Règles générales, méthodes


d’essai et guide pratique













INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 29.120.20 ISBN 978-2-8322-8086-7




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------
SIST EN IEC 60352-3:2020
– 2 – IEC 60352-3:2020 © IEC 2020
CONTENTS
FOREWORD . 5
INTRODUCTION . 7
1 Scope . 9
2 Normative references . 9
3 Terms and definitions . 10
4 Workmanship . 13
5 Prerequisites for basic test schedule . 13
5.1 General . 13
5.2 Prerequisites for accessible ID terminations . 14
5.2.1 Accessible ID termination materials . 14
5.2.2 Accessible ID termination dimensions . 14
5.2.3 Accessible ID termination surface finishes . 14
5.2.4 Accessible ID termination design features . 14
5.3 Prerequisites for wires and conductors. 14
5.3.1 Wires and conductors . 14
5.3.2 Wire insulation . 15
5.4 Accessible insulation displacement connections (accessible ID connections) . 15
6 Testing . 15
6.1 Introduction . 15
6.2 General . 15
6.3 Standard conditions for testing . 16
6.4 Preconditioning . 16
6.5 Recovery . 16
6.6 Mounting of specimen . 16
7 Tests . 16
7.1 General examination . 16
7.2 Mechanical tests . 17
7.2.1 Transverse extraction force . 17
7.2.2 Bending of the wire . 18
7.2.3 Vibration . 19
7.2.4 Repeated connection and disconnection, reusable accessible ID
terminations . 20
7.3 Electrical tests . 20
7.3.1 General . 20
7.3.2 Contact resistance . 21
7.3.3 Electrical load and temperature . 22
7.4 Climatic tests . 22
7.4.1 General . 22
7.4.2 Rapid change of temperature . 22
7.4.3 Climatic sequence . 22
7.4.4 Flowing mixed gas corrosion test . 22
7.4.5 Damp heat, cyclic . 23
8 Test schedules . 23
8.1 General . 23
8.1.1 Overview . 23

---------------------- Page: 8 ----------------------
SIST EN IEC 60352-3:2020
IEC 60352-3:2020 © IEC 2020 – 3 –
8.1.2 ID connections with terminations suitable for a range of wire diameters . 23
8.1.3 Multipole connectors . 23
8.2 Basic test schedule . 24
8.2.1 Généralités . 24
8.2.2 Initial examination . 24
8.2.3 Testing of accessible ID connections . 24
8.3 Full test schedule . 26
8.3.1 General . 26
8.3.2 Initial examination . 26
8.3.3 Testing of accessible ID connections . 26
8.4 Flow charts . 29
Annex A (informative) Practical guidance . 32
A.1 General information on accessible ID connections . 32
A.1.1 General . 32
A.1.2 Advantages of accessible ID connections . 32
A.2 Current-carrying capacity . 33
A.3 Tool information . 33
A.3.1 Wire insertion tool . 33
A.3.2 Wire extraction tool . 33
A.3.3 Combination tool. 33
A.4 Termination information . 33
A.4.1 General . 33
A.4.2 Design features . 34
A.4.3 Materials . 34
A.4.4 Surface finishes . 34
A.5 Wire information. 34
A.5.1 Type . 34
A.5.2 Dimensions . 34
A.5.3 Surface finishes . 34
A.5.4 Insulation . 34
A.6 Connection information . 35
Annex B (informative) Application examples . 37
B.1 Examples for good IDCs or negative results (see Figure B.1 to Figure B.7) . 37
B.2 Examples for good transversal micro section or negative results . 39
Bibliography . 40

Figure 1 – Example of accessible and non-accessible insulation displacement
connection . 7
Figure 2 – Insulation displacement connection . 11
Figure 3 – Slot . 12
Figure 4 – Beam . 13
Figure 5 – Test arrangement, transverse extraction force. 17
Figure 6 – Test arrangement, bending of the wire . 18
Figure 7 – Test arrangement, vibration . 19
Figure 8 – Test arrangement, contact resistance . 21
Figure 9 – Basic test schedule (see 8.2) . 30
Figure 10 – Full test schedule (see 8.3) . 31

---------------------- Page: 9 ----------------------
SIST EN IEC 60352-3:2020
– 4 – IEC 60352-3:2020 © IEC 2020
Figure A.1 – Example of a single-type accessible ID termination with a solid round
conductor . 36
Figure B.1 – Example of correct and acceptable ID connections . 37
Figure B.2 – Examples for good IDCs or negative results . 37
Figure B.3 – Faulty IDC: damaged contacts . 38
Figure B.4 – Requirements for open-ended IDCs . 38
Figure B.5 – Faulty IDC: damaged wire . 38
Figure B.6 – IDC: Wire position . 39
Figure B.7 – IDC: transversal micro section . 39

Table 1 – Minimum transverse extraction force . 18
Table 2 – Vibration, preferred test severities . 19
Table 3 – Contact resistance of accessible ID connections, maximum permitted values . 21
Table 4 – Number of specimens required . 24
Table 5 – Qualification test schedule – Test group 1 . 25
Table 6 – Qualification test schedule – Test group 2 . 25
Table 7 – Qualification test schedule – Test group 3 . 26
Table 8 – Qualification test schedule – Test group A . 27
Table 9 – Qualification test schedule – Test group B . 27
Table 10 – Qualification test schedule – Test group C . 28
Table 11 – Qualification test schedule – Test group D . 29
Table 12 – Qualification test schedule – Test group E . 29

---------------------- Page: 10 ----------------------
SIST EN IEC 60352-3:2020
IEC 60352-3:2020 © IEC 2020 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

SOLDERLESS CONNECTIONS –

Part 3: Accessible insulation displacement (ID) connections –
General requirements, test methods and practical guidance

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote interna-
tional co-operation on all questions concerning standardization in the electrical and electronic fields. To this
end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Tech-
nical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publica-
tion(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested in the
subject dealt with may participate in this preparatory work. International, governmental and non-governmental
organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the Interna-
tional Organization for Standardization (ISO) in accordance with conditions determined by agreement between
the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all inter-
ested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinter-
pretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence be-
tween any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and ex-
penses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publica-
tions.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60352-3 has been prepared by subcommittee 48B: Electrical
connectors, of IEC technical committee 48: Electrical connectors and mechanical structures
for electrical and electronic equipment.
This second edition cancels and replaces the first edition published in 1993. This edition con-
stitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) Subclause 7.2.2: reduce the limit of duration of contact disturbance to 1 µs.
b) Subclause 7.2.3: reduce the limit of duration of contact disturbance to 1 µs.
c) Transferred Clauses 9 to 13 to Annex A (informative).
d) The figures were revised for clarity.

---------------------- Page: 11 ----------------------
SIST EN IEC 60352-3:2020
– 6 – IEC 60352-3:2020 © IEC 2020
The text of this International Standard is based on the following documents:
FDIS Report on voting
48B/2789/FDIS 48B/2802/RVD

Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts in the IEC 60352 series, published under the general title Solderless connec-
tions, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 12 ----------------------
SIST EN IEC 60352-3:2020
IEC 60352-3:2020 © IEC 2020 – 7 –
INTRODUCTION
The two following parts of IEC 60352 are available on solderless insulation displacement con-
nections:
– Part 3: Accessible insulation displacement connections – General requirements, test
methods and practical guidance;
– Part 4: Solderless non-accessible insulation displacement connections – General require-
ments, test methods and practical guidance.
NOTE In this document the term "insulation displacement" is abbreviated to "ID", for example "ID connection", "ID
termination".
Figure 1 illustrates examples of accessible and non-accessible insulation displacement con-
nections that clarify the difference among them.
Part 3 includes requirements and relevant tests (normative) as well as a practical guidance in
Annex A (informative) for accessible ID connections.
Two test schedules are provided:
– the basic test schedule which applies to insulation displacement connections which con-
form to all prerequisites of Clause 5. It is derived from experience with successful applica-
tions of such connections;
– the full test schedule which applies to insulation displacement connections which do not
fully conform to all prerequisites of Clause 5, for example which are manufactured using
materials or finishes not included in Clause 5.
This philosophy permits cost and time effective performance verification using a limited basic
test schedule for established insulation displacement connections and an expanded full test
schedule for connections requiring more extensive performance validation.
The suitability of the accessible
...