SIST EN ISO 2400:2013

SLOVENSKI STANDARD
SIST EN ISO 2400:2013
01-februar-2013
1DGRPHãþD
SIST EN 12223:2000
1HSRUXãLWYHQRSUHVNXãDQMH8OWUD]YRþQHSUHLVNDYH6SHFLILNDFLMH]DXPHULWYHQL
Y]RUHFãW,62
Non-destructive testing - Ultrasonic examination - Specification for calibration block No. 1
(ISO 2400:2012)
Zerstörungsfreie Prüfung - Ultraschallprüfung - Beschreibung des Kalibrierkörpers Nr 1
(ISO 2400:2012)
Essais non destructifs - Contrôle par ultrasons - Spécifications relatives au bloc
d'étalonnage n° 1 (ISO 2400:2012)
Ta slovenski standard je istoveten z: EN ISO 2400:2012
ICS:
19.100 Neporušitveno preskušanje Non-destructive testing
SIST EN ISO 2400:2013 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 2400:2013

---------------------- Page: 2 ----------------------

SIST EN ISO 2400:2013


EUROPEAN STANDARD
EN ISO 2400

NORME EUROPÉENNE

EUROPÄISCHE NORM
September 2012
ICS 25.160.40 Supersedes EN 12223:1999
English Version
Non-destructive testing - Ultrasonic testing - Specification for
calibration block No. 1 (ISO 2400:2012)
Essais non destructifs - Contrôle par ultrasons - Zerstörungsfreie Prüfung - Ultraschallprüfung -
Spécifications relatives au bloc d'étalonnage n° 1 (ISO Beschreibung des Kalibrierkörpers Nr 1 (ISO 2400:2012)
2400:2012)
This European Standard was approved by CEN on 14 September 2012.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 2400:2012: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 2400:2013
EN ISO 2400:2012 (E)
Contents Page
Foreword .3
2

---------------------- Page: 4 ----------------------

SIST EN ISO 2400:2013
EN ISO 2400:2012 (E)
Foreword
This document (EN ISO 2400:2012) has been prepared by Technical Committee CEN/TC 138 “Non-
destructive testing”, the secretariat of which is held by AFNOR, in collaboration with Technical Committee
ISO/TC 135 "Non-destructive testing".
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by mars 2013, and conflicting national standards shall be withdrawn at
the latest by mars 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12223:1999.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 2400:2013

---------------------- Page: 6 ----------------------

SIST EN ISO 2400:2013
INTERNATIONAL ISO
STANDARD 2400
Second edition
2012-09-15
Non-destructive testing — Ultrasonic
testing — Specification for calibration
block No. 1
Essais non destructifs — Contrôle par ultrasons — Spécifications
o
relatives au bloc d’étalonnage n 1
Reference number
ISO 2400:2012(E)
©
ISO 2012

---------------------- Page: 7 ----------------------

SIST EN ISO 2400:2013
ISO 2400:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 2400:2013
ISO 2400:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 2400 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 138, Non-destructive testing, in collaboration with Technical Committee ISO/TC 135, Non-destructive
testing, Subcommittee SC 3, Ultrasonic testing, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 2400:1972), which has been technically revised.
Changes from the first edition include the addition of:
— a new clause on manufacture of the block;
— a new clause on sound velocities;
— a new clause on marking and certification of the blocks;
— a new clause on possible modifications to block No. 1;
— a new clause on the use of existing blocks;
— a normative annex on the determination of velocities.
© ISO 2012 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 2400:2013

---------------------- Page: 10 ----------------------

SIST EN ISO 2400:2013
INTERNA
...