SIST EN ISO 8735:2001

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Zylinderstifte mit Innengewinde aus gehärtetem Stahl und martensitischem nichtrostendem Stahl (ISO 8735:1997)Goupilles cylindriques a trou taraudé en acier trempé et en acier inoxydable martensitique (ISO 8735:1997)Parallel pins with internal thread, of hardened steel or martensitic stainless steel (ISO 8735:1997)21.060.50Pins, nailsICS:Ta slovenski standard je istoveten z:EN ISO 8735:1997SIST EN ISO 8735:2001en01-julij-2001SIST EN ISO 8735:2001SLOVENSKI
STANDARD



SIST EN ISO 8735:2001



SIST EN ISO 8735:2001



SIST EN ISO 8735:2001



SIST EN ISO 8735:2001



SIST EN ISO 8735:2001



AReference numberISO 8735:1997(E)INTERNATIONALSTANDARDISO8735Second edition1997-11-15Parallel pins with internal thread,of hardened steel and martensiticstainless steelGoupilles cylindriques à trou taraudé en acier trempé eten acier inoxydable martensitiqueSIST EN ISO 8735:2001



ISO 8735:1997(E)©
ISO 1997All rights reserved. Unless otherwise specified, no part of this publication may be reproducedor utilized in any form or by any means, electronic or mechanical, including photocopying andmicrofilm, without permission in writing from the publisher.International Organization for StandardizationCase postale 56 · CH-1211 Genève 20 · SwitzerlandInternetcentral@iso.chX.400c=ch; a=400net; p=iso; o=isocs; s=centralPrinted in SwitzerlandiiForewordISO (the International Organization for Standardization) is a worldwidefederation of national standards bodies (ISO member bodies). The work ofpreparing International Standards is normally carried out through ISOtechnical committees. Each member body interested in a subject for whicha technical committee has been established has the right to be representedon that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISOcollaborates closely with the International Electrotechnical Commission(IEC) on all matters of electrotechnical standardization.Draft International Standards adopted by the technical committees arecirculated to the member bodies for voting. Publication as an InternationalStandard requires approval by at least 75 % of the member bodies castinga vote.International Standard ISO 8735 was prepared by Technical CommitteeISO/TC 2, Fasteners.This second edition cancels and replaces the first edition (ISO 8735:1987),which has been technically revised.SIST EN ISO 8735:2001



INTERNATIONAL STANDARD
© ISOISO 8735:1997(E)1Parallel pins with internal thread of hardened steel andmartensitic stainless steel1
ScopeThis International Standard specifies the characteristics of parallel pins with internal thread of steel, throughhardened or case hardened and martensitic stainless steel, with nominal diameters d1 from 6 mm to 50 mminclusive.2
Normative referencesThe following standards contain provisions which, through reference in this text, constitute provisions of thisInternational Standard. At the time of publication, the editions indicated were valid. All standards are subjectto revision, and parties to agreements based on this International Standard are encouraged to investigate thepossibility of applying the most recent editions of the standards indicated below. Members of IEC and ISOmaintain registers of currently valid International Standards.ISO 965-2:–1), ISO general purpose metric screw threads – Tolerances – Part 2: Limits of sizes for generalpurpose bolt and nut threads – Medium quality.ISO 3269:1988, Fasteners – Acceptance inspection.ISO 3506
...