SIST EN 60603-6:2002

SLOVENSKI STANDARD
SIST EN 60603-6:2002
01-september-2002
Connectors for frequencies below 3 MHz for use with printed boards - Part 6: Edge
-socket connectors and printed-board connectors with 2,54 mm (0,1 in) contact
spacing for single or double-sided printed boards of 1,6 mm (0,063 in) nominal
thickness (IEC 60603-6:1987)
Connectors for frequencies below 3 MHz for use with printed boards -- Part 6: Edge-
socket connectors and printed-board connectors with 2,54 mm (0,1 in) contact spacing
for single or double-sided printed boards of 1,6 mm (0,063 in) nominal thickness
Steckverbinder für gedruckte Schaltungen für Frequenzen unter 3 MHz -- Teil 6: Direkte
Steckverbinder und Steckverbinder für gedruckte Schaltungen mit 2,54 mm (0,1 in)
Kontaktabstand für ein- oder beidseitig beschichtete Leiterplatten mit 1,6 mm (0,063 in)
Nenndicke
Connecteurs pour fréquences inférieures à 3 MHz pour utilisation avec cartes imprimées
-- Partie 6: Connecteurs encartables et pour cartes imprimées à écartement des contacts
de 2,54 mm (0,1 in) pour cartes imprimées simple ou double face, ayant une épaisseur
nominale de 1,6 mm (0,063 in)
Ta slovenski standard je istoveten z: EN 60603-6:1998
ICS:
31.220.10 9WLþLLQYWLþQLFHNRQHNWRUML Plug-and-socket devices.
Connectors
SIST EN 60603-6:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60603-6:2002

---------------------- Page: 2 ----------------------

SIST EN 60603-6:2002

---------------------- Page: 3 ----------------------

SIST EN 60603-6:2002

---------------------- Page: 4 ----------------------

SIST EN 60603-6:2002

---------------------- Page: 5 ----------------------

SIST EN 60603-6:2002

---------------------- Page: 6 ----------------------

SIST EN 60603-6:2002
NORME
CEI
INTERNATIONALE
IEC
603-6
INTERNATIONAL
Première édition
STAN DARD
First edition
1987
Connecteurs pour fréquences inférieures à 3 MHz
pour utilisation avec cartes imprimées
Sixième partie:
Connecteurs encartables et pour cartes imprimées à
écartement des contacts de 2,54 mm (0,1 in) pour
simple ou double face, ayant une
cartes imprimées
épaisseur nominale de 1,6 mm (0,063 in)
Connectors for frequencies below 3 MHz
for use with printed boards
Part 6:
Edge-socket connectors and printed-board connectors
with 2.54 mm (0.1 in) contact spacing for single or
double-sided printed boards of 1.6 mm (0.063 in)
nominal thickness
© CEI 1987 Droits de reproduction réservés — Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized
utilisée sous quelque forme que ce soit et par aucun procédé, in any form or by any means, electronic or mechanical,
électronique ou mécanique, y compris la photocopie et les including photocopying and microfilm, without permission
microfilms, sans l'accord écrit de l'éditeur. in writing from the publisher
Bureau central de la Commission Electrotechnique Internationale 3, rue de Varembé Genève Suisse
, n,
Commission Electrotechnique Internationale CODE PRIX
International Electrotechnical Commission PRICE CODE ^/V
IEC MewiyHapoJHa i 3neKTpoTexHN4ecKaR HOMHCCHA
• Pour prix, voir catalogue en vigueur
•
For price, see current catalogue

---------------------- Page: 7 ----------------------

SIST EN 60603-6:2002
603-6 © I E C 1987 — 3 —
CONTENTS
Page
FOREWORD 5
PREFACE 5
Clause
1. Scope 7
2. IEC type designation 9
11
3. Common features
17
4. Dimensions
51
5. Gauges
63
6. Characteristics
65
7. Test schedule

---------------------- Page: 8 ----------------------

SIST EN 60603-6:2002
— 5 —
603-6 © IEC 1987
INTERNATIONAL ELECTROTECHNICAL COMMISSION
CONNECTORS FOR FREQUENCIES BELOW 3 MHz FOR USE
WITH PRINTED BOARDS
Part 6: Edge-socket connectors and printed-board connectors
with 2.54 mm (0.1 in) contact spacing for single or double-sided printed boards
of 1.6 mm (0.063 in) nominal thickness
FOREWORD
The formal decisions or agreements of the IEC on technical matters, prepared by Technical Committees on which all the
1)
National Committees having a special interest therein are represented, express, as nearly as possible, an international
consensus of opinion on the subjects dealt with.
They have the form of recommendations for international use and they are accepted by the National Committees in that sense.
2)
order to promote international unification, the IEC expresses the wish that all National Committees should adopt the text
3) In
of the IEC recommendation for their national rules in so far as national conditions will permit. Any divergence between the
IEC recommendation and the corresponding national rules should, as far as possible, be clearly indicated in the latter.
4) The IEC has not laid down any procedure concerning marking as an indication of approval and has no responsibility when an
item of equipment is declared to comply with one of its recommendations.
PREFACE
This standard has been prepared by Sub-Committee 48B: Connectors, of IEC Technical Committee
No.48: Electromechanical Components for Electronic Equipment.
The text of this standard is based on the following documents:
Report on Voting
Six Months' Rule
48B(CO)133 48B(CO)145
Further information can be found in the Report on Voting indicated in the table above.

---------------------- Page: 9 ----------------------

SIST EN 60603-6:2002
— 7 —
603-6 © I E C 1987
CONNECTORS FOR FREQUENCIES BELOW 3 MHz FOR USE
WITH PRINTED BOARDS
Edge-socket connectors and printed-board connectors
Part 6:
with 2.54 mm (0.1 in) contact spacing for single or double-sided printed boards
of 1.6 mm (0.063 in) nominal thickness
1. Scope
This standard covers a range of connectors with 2.54 mm (0.1 in) contact spacing intended to connect
a single or double-sided printed board to another printed board or wires.
Two kinds are available:
Edge-socket connector
A connector with female contacts intended to mate with edge-board contacts and with printed-board
connectors having male contacts.
Edge-socket connectors are available with:
solder terminations for wire;
–
– solder terminations for board mounting;
– wrap terminations.
Printed-board connector
A connector having male contacts which when mounted on a printed board replaces the edge-board
contacts.
Printed-board connectors are provided with solder terminations for single or double-sided boards of
1.6 mm (0.063 in) nominal thickness.
An edge-socket connector mated with a printed-board connector is referred to as a two-part con-
nector in this standard.
The mandatory method of locating is by means of a guide key which replaces an opposite pair of
contacts, and one such key is provided per connector (see also Sub-clause 4.5)
This standard shall be used in conjunction with the following IEC publications:
Nos. 50 (581) (1978): International Electrotechnical Vocabulary, Chapter 581: Electromechanical
Components for Electronic Equipment.
603-1 (1981): Connectors for Frequencies Below 3 MHz for Use with Printed Boards, Part 1:
General Rules and Guide for the Preparation of Detail Specifications.
512-2 (1976): Electromechanical Components for Electronic Equipment; Basic Testing
Procedures and Measuring Methods, Part 2: General Examination, Electrical
Continuity and Contact Resistance Tests, Insulation Tests and Voltage Stress
Tests.
512-3 (1976): Part 3: Current-carrying Capacity Tests.
512-6 (1984): Part 6: Climatic Tests and Soldering Tests.
512-7 (1978): Part 7: Mechanical Operating Tests and Sealing Tests.
Amendment No.1 (1983).

---------------------- Page: 10 ----------------------

SIST EN 60603-6:2002
603-6 © I E C 1987 — 9 —
2. IEC type designation
X X XX X 603-6IEC X XX X
No. of detail specification/IEC
Style
Number of ways
Single or double-sided and active contact row
Termination style
Contact finish
Contact removal/replacement system
Variant
No. of detail specification/IEC: 603-6 IEC
As shown in Clauses 3 and 4 of this standard.
Style:
Digits denoting the number of contact locations along one side of the
Number of ways:
connector. Maximum 85 for Styles 1, 2, 3 and 5, and 80 for Style 4.
Single or double-
sided and active
A = single-sided, side A active, single row of terminations
contact row:
B = single-sided, side B active, single row of terminations
E = single-sided, side A active, double row of terminations
F = single-sided, side B active, double row of terminations
D = double-sided, both sides active
Termination
S = solder terminations for wire
style:
B = solder terminations for printed board
W= wrap terminations
T = through-board solder, short termination
L = through-board solder, long termination
X = through-board solder, extra long termination
Contact
finish: A = gold alloy
Contact removal/
replacement
A = rear release/front removable/replaceable contacts
system:
B = rear release/rear removable/replaceable contacts
C = front release/front removable/replaceable contacts
D = front release/rear removable/replaceable contacts
Digits identifying individual connector, parts and associated tools for
Variant:
replacement purposes.
Example of
type designation: 603-6IEC A 80 B W A C XX

---------------------- Page: 11 ----------------------

SIST EN 60603-6:2002

— 11 —
603-6 © I E C 1987
3. Common features
3.1 Perspective views
3.1.1 Edge-socket connector

---------------------- Page: 12 ----------------------

SIST EN 60603-6:2002
— 13 —
603-6 © I E C 1987
3.1.2 Printed-board connector

---------------------- Page: 13 ----------------------

SIST EN 60603-6:2002
603-6 © I E C 1987 — 15 —
3.1.3 Values
Reference
Legend
lette
al Pitch of terminations of printed-board connector
a2 Pitch of contacts of edge-socket connector
b2 Distance between two rows
C1 Maximum overall length of printed-board connector
C2
C3 Maximum overall length of edge-socket connector
C4
D Maximum overall width of edge-socket connector
H1 Distance between mating face of printed-board connector and board
M2
M3 Distance between mounting plane of edge-socket connector and bottom of board slot
M4
W Minimum length of mounting cut-out
Distance between fixing holes of edge-socket connector
X
Z Minimum width of mounting cut-out

---------------------- Page: 14 ----------------------

SIST EN 60603-6:2002
- 17 -
603-6 © I E C 1987
Edge-socket Edge-socket
Reference Printed-board Edge-socket
connector connector connector
letter connector
metal feet closed ends
Styles 1 and 2 Style 3 Style 4
Style 5
2.54 n + 0.43
C 1 max.
(0.1 n + 0.017)
2.54 n+ 6
C2 max
(0.1 n + 0.236)
2.54 n + 30
-
C3 max.
+
(0.1 n 1.18)
2.54 n + 29.8
4 - -
C C max.
(0.1 n + 1.17)
10 10,4 10,4 10,4
D max.
(0.394) (0.41) (0.41) (0.41)
13.9/14.5
111
(0.55/0.57)
4.24/6.0 -
_
M2 Style 1
(0.167/0.236)
6.0/7.5
M2 Style 2
(0.236/0.295)
7.3/8.3
M3 A4
(0.29/0.33)
W See page 43
_ 25.4 n+ 16.2 2.5 n+ 16.2
X
(0.1 n + 0.64) (0.1 n + 0.64)
11 11 11
Z min.
(0.433) (0.433) (0.433)
2.54 2.54 2.54
2.54
al
(0.1) (0.1) (0.1) (0.1)
2.54 2.54 2.54 2.54
az
(0.1) (0.1) (0.1) (0.1)
5.08 5.08 5.08 5.08
b2
(0.2) (0.2) (0.2) (0.2)
number of contact positions along one side of connector.
Notes I. - n =
2. - Dimensions in millimetres (inch dimensions in parentheses).
4. Dimensions
4.1
General
Dimensions in millimetres are original. Drawings are shown in third angle projection. The shape of
the connectors may deviate from those given in the following drawings as long as the specified dimen-
sions are not influenced.

---------------------- Page: 15 ----------------------

SIST EN 60603-6:2002

— 19 —
603-6 © IEC 1987
4.2 Connectors
4.2.1
Edge-socket connector
Styles 1 and 2, open-ended.
2 n Contacts
Guide key, polarizing
(typical position)
See Note 1
See Notes 1 and 2
I-12/1 0001 0.2 (0.008)
//
N
m
N
CI)
I--
^ ^
N
Z
Mounting plane
C2 0.2 (0.008) B
QM
3/1 000f 10.2 (0.008) 0IA 1
r
631/87
Notes 1. — This tolerance should lie within dimensions e2.
This measurement should be made with the component mounted in the normal manner.
2. —
— Dimensions 12 should be effective within card slot engagement area.
3.
— Replacement guide keys and contacts should be identical to the originals.
4.
— Row identification A and B is mandatory. Numerical marking is typical.
5.

---------------------- Page: 16 ----------------------

SIST EN 60603-6:2002
— 21 —
603-6 © IEC 1987
mm in
Dimension
0.642
A 2 max. 16.3
9.3/7.8 0.37/0.31
B 2
2.54 n + 6 0.1 n + 0.236
C2 max.
0.41
F2 max. 10.4
x
G2 (n-1) 2.54 (n-1) x 0.1
4.24/6.0 0.167/0.236
M2 style 1
6.0/7.5 0.236/0.295
M2 style 2
a2 2.54 0.1
b2 5.08 0.2
1.85 0.07
c2 min.
0.12
d2 min. 3.10
e2 4.3/5.0 0.17/0.20
f2 5.05/5.20 0.199/0.205
g2 See page 35
0.02
h2 min. 0.5
j2 1.58/1.52 0.062/0.060
number of contact positions along one side of connector (maximum permissible = 85).
Note. — n =

---------------------- Page: 17 ----------------------

SIST EN 60603-6:2002
— 23 —
603-6 © I E C 1987
4.2.2 Edge-socket connector, open-ended with metal mounting feet, Style 3
IG3 ►
0.2 (0.008) min.
Radius or chamfer
Guide key, locating
2 n Contacts
(typical position)
See detail, 4.2.5
4)I
A
Guide key, polarizing
3/1000
(typical position)
See Notes 3 and 4
L3
I=I0.2 ( 0.008)B
See Note 1
See Notes 1 and 2
// 0.2 (0.008)
See Note 5 0.2 (0.008) QM
^ a3
\^+ N (h
d-
C3
Two holes ¢ d3
IA I
4193 0.2 (0.008)
May be elongated 632/87
Notes 1. — This tolerance zone should lie within dimension M3.
These measurements should be made with the components mounted in the normal manner.
2. —
— This dimension should be effective within card slot engagement area.
3.
4. — Replacement contacts and guide keys should be identical to the originals.
Row identification A and B is mandatory. Numerical marking is typical.
5. —

---------------------- Page: 18 ----------------------

SIST EN 60603-6:2002
— 25 —
603-6 © I E C 1987
mm in
Dimension
0.69
17.6
A 3 max.
0.37/0.31
B 3 9.3/7.8
n + 30 0.1 n + 1.81
C3 max. 2.54
0.12
3.10
D3 min.
10.4 0.41
D max.
(n-1) x 2.54 (n-1) x 0.1
G3
0.1 n + 0.40
L 3 2.54 n + 10.1
max.
0.29/0.33
M3 7.3/8.3
2.54 n + 16.2 0.1 n + 0.64
X
0.1
a3 2.54
0.2
b3 5.08
0.07
1.85
c3 min.
3.15 0.12
d3 min.
g3 See page 35
0.02
min. 0.5
h3
0.062/0.060
j3 1.58/1.52
number of contact positions along one side of connector (maximum permissible = 85).
Note. — n =

---------------------- Page: 19 ----------------------

SIST EN 60603-6:2002
603-6 O
I E C 1987 — 27 —
4.2.3 Edge-socket connector, closed ends, Style 4
/4
See Notes 3 and 4
0.2 (0.008) min.
r
Radius or chamfer
/
^ a[,;i oo,aa
^ _^0^ Z0. ^ , _
0,0 0-
Guide key, polarizing
Guide key, locating
(typical position)
(typical position)
2 n Contacts
See detail, 4.2.5 ID I I-13/1000)
14!
B
B MQI
I = 0.2 (0.008)
N4
MOI
D4
See Note 1
See Notes 1 and 2
I –1_ 2/1000 1 // 0.2 (0.008) j
0.2 (0.008) -B OM
C4 1 01
Two holes O a14
A B MQ
0.2 (0.008)1
See Note 5
may be elongated
f
---^
^^
^1 j-
N
a4
I G4
0.2 (0.008)IC
oI
CAA MO( 1-=10.2 (0.008)
633/87
Notes 1. – This tolerance zone should lie within dimension M4.
2. – These measurements should be made with the components mounted in the normal manner.
3. – This dimension should be effective within card slot engagement area.
4. – Replacement contacts and guide keys should be identical to the originals.
5. – Row identification A and B is mandatory. Numerical marking is typical.

---------------------- Page: 20 ----------------------

SIST EN 60603-6:2002
603-6 © I E C 1987 - 29 -
Dimension mm in
17.6 0.69
A4 max.
B 4 9.3/7.8 0.37/0.31
C4 max. 2.54 n + 29.8 0.1 n + 1.17
3.10 0.12
D4 min.
E4 1.1/1.2 0.043/0.047
D max. 10.4 0.41
(n-1) x 2.54 (n-1) x 0.1
G4
2.54 n + 0.1 n + 0.40
L4 max. 10.1
N4 (2.54 n + 0.5)1 (0.1 n + 0.002)1016
4
X 2.54 n + 16.2 0.1 n + 0.64
a4 2.54 0.1
b4 5.08 0.2
c4 min. 1.85 0.07
d4 min. 3.40 0.13
f4
g4 See page 35
h4 min. 0.5 0.02
1.58/1.52 0.062/0.060
f4
Note. - n = number of contact positions along one side of connector (maximum permissible = 80).

---------------------- Page: 21 ----------------------

SIST EN 60603-6:2002
603-6 © — 31 —
IEC 1987
4.2.4 Printed-board connector, Style 5
— 1/1000
Ci
I-I I BF--
r
8
1-11/1000
Pill 2/1000 I C J
B
0.2 (0.008)
At user's discretion
(see 4.6.3)
A
—12/10001
A
a1
m
`I
Typical, guide slot
(locating)
k1
634/87
Notes 1. — Two pairs of retaining clamps should be supplied with connectors of size up to 30 way.
Three pairs of retaining clamps should be supplied with connectors from 31 way to max. size.
2. —Positions of guide slots should be specified by the user (polarizing slots only if required).

---------------------- Page: 22 ----------------------

SIST EN 60603-6:2002
— 33 —
603-6 © I E C 1987
in
Dimension mm
1.00
25.4
A l max.
9.4 0.37
B i min.
2.54 n + 0.30 0.1 n + 0.017
C1 max.
0.11/0.15
E1 2.8/3.7
10 0.394
D 1 max.
G 1 2.54 P 0.1 P
0.57/0.55
H1 14.5/13.9
0.1 P
2.54 P
J1
(2.54 P + 1.42)1 5 (0.1 P +
K 1 0.05)_g.0047
7 0.276
L 1 max.
0.1
a1 2.54
0.060/0.069
c1 1.52/1.74
3.05 0.12
d 1 max.
1.85 0.07
g 1 min.
0.058/0.060
1.47/1.52
jl
2.0/2.2 0.079/0.087
k 1
11 1.65/1.75 0.065/0.069
0.25
m 1 min. 6.5
0.83
Pi max. 21.1
2 0.079
q 1 max.
1.5/1.7 0.059/0.067
r1
0.26
s i max. 6.6
number of pitches from datum A slot.
Notes 1. — P =
2. — n = number of contact positions along one side of connector.

---------------------- Page: 23 ----------------------

SIST EN 60603-6:2002
— 35 —
603-6 © I E C 1987
4.2.5 Zone of electrical contact
a
x
True position of connector
contact pitch
Base of printed board slot
in connector
635/87
Dimension
mm in
a 0.65 0.026
b 6.1 0.24
c 3.3 0.13
6.1 0.24
g1
3.3 0.13
Notes 1. — All dimensions are derived using printed board shown on page 49 and located with appropriate guide key.
2. — Electrical contact should be made within the zone of board pad as on page 49. The contact may extend beyond
this zone providing the specified voltage proof requirements are met.

---------------------- Page: 24 ----------------------

SIST EN 60603-6:2002
603-6 © I E C 1987 — 37 —
4.3 Terminations of edge-socket connectors
4.3.1 Solder terminations for wire, S tyles S and B
Mounting
plane
mm in
7.5 0.29
T1
1.8 0.07
637/87
Eyelet solder terminations permit the connection of two wires,
...