SIST EN 2131:2004

SLOVENSKI STANDARD
SIST EN 2131:2004
01-maj-2004
Aerospace series - Plates in aluminium alloys - Thickness 6 mm < a < 160 mm -
Dimensions
Aerospace series - Plates in aluminium alloys - Thickness 6 mm < a < 160 mm -
Dimensions
Luft- und Raumfahrt - Platten aus Aluminiumlegierungen - Dicken 6 mm < a < 160 mm -
Maße
Série aérospatiale - Plaques en alliages d'aluminium - Épaisseurs 6 mm < a < 160 mm -
Dimensions
Ta slovenski standard je istoveten z: EN 2131:2001
ICS:
49.025.20 Aluminij Aluminium
SIST EN 2131:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 2131:2004

---------------------- Page: 2 ----------------------

SIST EN 2131:2004
EUROPEAN STANDARD
EN 2131
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2001
ICS 49.025.20
English version
Aerospace series - Plates in aluminium alloys - Thickness 6 mm
< a
160 mm - Dimensions
Série aérospatiale - Plaques en alliages d'aluminium - Luft- und Raumfahrt - Platten aus Aluminiumlegierungen -
Epaisseurs 6 mm < a
160 mm - Dimensions Dicken 6 mm < a
160 mm - Maße
This European Standard was approved by CEN on 2 May 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 2131:2001 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 2131:2004
EN 2131:2001 (E)
Foreword
This European Standard has been prepared by the European Association of Aerospace Manufacturers
(AECMA).
After inquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
AECMA, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2002, and conflicting national standards shall be withdrawn at
the latest by June 2002.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark,
Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal,
Spain, Sweden, Switzerland and the United Kingdom.
2

---------------------- Page: 4 ----------------------

SIST EN 2131:2004
EN 2131:2001 (E)
0 Introduction
This standard is part of the series of EN metallic material standards for aerospace applications. The general
organization of this series is described in EN 4258.
1 Scope
This standard specifies the dimensions and tolerances of:
Plates
in aluminium alloys
Thickness 6 mm
a  160 mm
for aerospace applications.
2 Normative references
This European Standard incorporates by dated or undated reference provisions from other publications.
These normative references are cited at the appropriate places in the text and the publications are listed
hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to
this European Standard only when incorporated in it by
...