Intermodal Loading Units - Marking - Part 1: Markings for identification

This European Standard provides a system for the identification and presentation of information about the ILU. The identification system is intended for general application, for example in documentation, control and communications (including automatic data processing systems), as well as for display on an ILU and other non ISO containers (i.e.: which dimensions and testing parameters differ from those defined by the applicable ISO standards) used in European transport.
The methods of displaying identification and certain other data (including operational data) on swap bodies by means of permanent marks are included.
This European Standard specifies:
a)   an ILU identification system with an associated system for verifying the accuracy of its use, having mandatory marks for the presentation of the identification system for visual interpretation, and
b)   a coding system for data on ILU size and type, with corresponding marks for their display;
c)   mandatory operational marks;
d)   physical presentation of the marks on the ILU.
This Part of EN 13044 specifies a system to identify the owner of the ILU, which includes an associated system for verifying the accuracy of its use.
This European Standard does not cover temporary operational marks of any kind, permanent marks, data plates, etc. which may be required by intergovernmental agreements, national legislation or non-governmental organisations other than CEN.
NOTE   Some of the major international conventions whose container-marking requirements are not covered in this European Standard are as follows:
-   International Convention for Safe Containers (UN/IMO 1992);
-   Customs Convention on Containers 1956 and 1972;
-   Customs Convention on International Movement of Goods under Cover of TIR Carnets (TIR-Convention) 1959 and 1975.
It should not to be assumed that this list is exhaustive.

Intermodale Ladeeinheiten - Kennzeichnung - Teil 1: Kennzeichnungen für die Identifizierung

Diese Europäische Norm beschreibt ein System zur Identifizierung und Kennzeichnung von ILU. Das Identifizierungssystem ist für die allgemeine Anwendung zu benutzen, wie beispielsweise bei der Dokumentation, Steuerung und Kommunikation (einschließlich automatischer Datenverarbeitungssysteme) und auch für das Anzeigen der Informationen an ILU und anderen „Nicht-ISO-Containern“ (z.B. deren Abmessungen und Prüfparameter sich von den in den anwendbaren ISO Standards unterscheiden) die im europäischen Transport benutzt werden.
Die Art der Anbringung der Kennzeichnung und anderer Informationen (einschließlich betrieblicher Daten) an ILU mittels permanenter Kennzeichen ist eingeschlossen.
Diese Europäische Norm beschreibt:
a)   ein System der Kennzeichnung von ILU, einschließlich eines Systems zur Kontrolle der korrekten Nutzung des Systems mit obligatorischen Kennzeichnungen für die Identifizierung zur visuellen Erkennbarkeit und
b)   ein Kodierungssystem für die Daten zur Größe und zum Type der ILU mit den dazugehörigen Hinweisen zur Anbringung der Kennzeichen;
c)   obligatorische betriebliche Kennzeichen;
d)   die physikalische Anbringungsmethode an der ILU
Dieser Teil der EN 13044 spezifiziert ein System zur Identifizierung des Eigentümers der ILU, einschließlich eines Systems zur Prüfung der Richtigkeit seiner Anwendung.
Diese Europäische Norm erfasst nicht vorübergehende betriebliche Kennzeichen irgendwelcher Art, bleibende Kennzeichnungen, Datenschilder usw., die durch Vereinbarungen zwischen Regierungen, nationale Gesetzgebung oder durch private Organisationen außer CEN eventuell gefordert werden.
ANMERKUNG      Einige der bedeutendsten internationalen Konventionen, welche die Kennzeichnung von ILU betreffen, sind nicht von dieser Europäischen Norm erfasst. Es sind dies die folgenden:

Unités de chargement intermodales - Marquage - Partie 1: Marquages d'identification

La présente Norme européenne établit un système pour l’identification et la présentation d’informations
relatives aux UCI. Ce système d’identification est prévu pour une application générale, par exemple pour la
documentation, le contrôle et les communications (y compris les systèmes de traitement informatique des
données), aussi bien que pour l’affichage sur une UCI et autres conteneurs non ISO (c’est-à-dire ceux dont
les dimensions et les valeurs d’essai diffèrent de celles définies par les normes ISO en vigueur) utilisés en
transport européen.
Les méthodes d’inscription de l’identification et de certaines autres données (y compris les données
d’exploitation) sur les UCI au moyen de marques permanentes sont également abordées.
La présente Norme européenne prescrit :
a) un système d’identification des UCI associé à un système permettant de vérifier l’exactitude de son
utilisation, comprenant des marques obligatoires pour la présentation du système d’identification à des
fins d’interprétation visuelle, et
b) un système de codage des données relatives aux dimensions et aux types d’UCI, avec les marques
correspondantes pour leur inscription ;
c) des marques d’exploitation obligatoires ;
d) la présentation concrète des marques sur l’UCI.
La présente Partie de l’EN 13044 spécifie un système permettant d’identifier le propriétaire de l’UCI, en
association avec un système de vérification de l’exactitude de son utilisation.
La présente Norme européenne ne couvre pas les marques temporaires d’exploitation quel que soit leur type,
les marques permanentes, les plaques de données, etc. qui peuvent être exigées par des accords
intergouvernementaux, des législations nationales ou des organisations non-gouvernementales autres que le
CEN.
NOTE Une liste des principales conventions internationales dont les exigences en termes de marque de conteneurs
ne sont pas abordées par la présente Norme européenne, est donnée ci-dessous :

Referenčne obremenilne enote - Označevanje - 1. del: Identifikacijske oznake

Ta evropski standard podaja sistem za identifikacijo in predstavitev informacij o referenčnih obremenilnih enotah (ILU). Identifikacijski sistem je namenjen splošni uporabi, na primer pri dokumentiranju, nadzoru in komunikacijah (vključno z avtomatskimi sistemi za obdelavo podatkov), ter prikazu na ILU in drugih zabojnikih, ki niso v skladu s standardi ISO (tj. katerih mere in preskusni parametri se razlikujejo od tistih, opredeljenih v veljavnih standardih ISO), ki se uporabljajo pri evropskem prevozu. Vključene so metode prikaza identifikacijskih in nekaterih drugih podatkov (vključno z obratovalnimi podatki) na ILU s trajnimi oznakami. Ta evropski standard določa: a) identifikacijski sistem ILU s povezanim sistemom za preverjanje natančnosti njegove uporabe, ki ima obvezne oznake za predstavitev identifikacijskega sistema za vidno interpretacijo; b) kodirni sistem za podatke o velikosti in tipu ILU z ustreznimi oznakami za njihov prikaz; c) obvezne obratovalne oznake; d) fizično predstavitev oznak na ILU. Ta del EN 13044 določa sistem za identifikacijo lastnika ILU, kar vključuje povezan sistem za preverjanje natančnosti njegove uporabe. Ta evropski sistem ne zajema začasnih obratovalnih oznak kakršne koli vrste, trajnih oznak, podatkovnih tablic itd., ki jih morda zahtevajo medvladni sporazumi, nacionalna zakonodaja ali nevladne organizacije, ki niso CEN.

General Information

Status
Published
Public Enquiry End Date
08-Mar-2009
Publication Date
03-Oct-2011
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
13-Sep-2011
Due Date
18-Nov-2011
Completion Date
04-Oct-2011

Relations

Buy Standard

Standard
EN 13044-1:2011
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 13044-1:2009
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Intermodale Ladeeinheiten - Kennzeichnung - Teil 1: Kennzeichnungen für die IdentifizierungUnités de chargement intermodales - Marquage - Partie 1: Marquages d'identificationIntermodal Loading Units - Marking - Part 1: Markings for identification55.180.10General purpose containers35.240.60Uporabniške rešitve IT v transportu in trgoviniIT applications in transport and tradeICS:Ta slovenski standard je istoveten z:EN 13044-1:2011SIST EN 13044-1:2011en,fr,de01-november-2011SIST EN 13044-1:2011SLOVENSKI
STANDARDSIST EN 13044:20001DGRPHãþD



SIST EN 13044-1:2011



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13044-1
January 2011 ICS 55.180.10; 35.240.60 Supersedes EN 13044:2000English Version
Intermodal Loading Units - Marking - Part 1: Markings for identification
Unités de chargement intermodales - Marquage - Partie 1: Marquages d'identification
Intermodale Ladeeinheiten - Kennzeichnung - Teil 1: Kennzeichnungen für die Identifizierung This European Standard was approved by CEN on 30 November 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13044-1:2011: ESIST EN 13044-1:2011



EN 13044-1:2011 (E) 2 Contents Page Foreword .3Introduction .41Scope .52Normative references .53Terms and definitions .64Identification system and its associated marks .64.1Identification system .64.2Identification of the owner .64.3Serial number .74.4Check digit .75Physical display of marks .75.1Size and colour of marks .75.2Layout and location of marks .75.2.1General .75.2.2Layout of marks .75.2.3Location of marks .7Annex A (normative)
Determination of check digit .9A.1General .9A.2Numerical equivalents of ILU identification system, and serial number .9A.3Weighting factor .9A.4Modulus .9A.5Value of check digit . 10A.6Example calculation of the check digit . 10Bibliography . 11 SIST EN 13044-1:2011



EN 13044-1:2011 (E) 3 Foreword This document (EN 13044-1:2011) has been prepared by Technical Committee CEN/TC 119 “Swap bodies for combined goods transport”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2011, and conflicting national standards shall be withdrawn at the latest by July 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13044:2000. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. SIST EN 13044-1:2011



EN 13044-1:2011 (E) 4 Introduction This European Standard contains the recommended method of marking Intermodal Loading Units (ILU) to meet current and future requirements. The European Standard follows the format used in EN ISO 6346, the world wide accepted standard for marking and coding of marine freight containers. As the above standard can be applied, without alteration, to an ILU, the standard is not directly interchangeable with the ISO standard. However since the ILU are handled and transported in Europe in the same environment as ISO freight containers, the two standards are compatible. SIST EN 13044-1:2011



EN 13044-1:2011 (E) 5 1 Scope This European Standard provides a system for the identification and presentation of information about the ILU. The identification system is intended for general application, for example in documentation, control and communications (including automatic data processing systems), as well as for display on an ILU and other non ISO containers (i.e. which dimensions and testing parameters differ from those defined by the applicable ISO standards) used in European transport.
The methods of displaying identification and certain other data (including operational data) on ILUs by means of permanent marks are included. This European Standard specifies: a) an ILU identification system with an associated system for verifying the accuracy of its use, having mandatory marks for the presentation of the identification system for visual interpretation; b) a coding system for data on ILU size and type, with corresponding marks for the
...

SLOVENSKI STANDARD
oSIST prEN 13044-1:2009
01-februar-2009
0HQMDOQHHQRWH NHVRQL 2]QDþHYDQMHGHO,GHQWLILNDFLMVNHR]QDNH
Swap bodies - Marking - Part 1: Markings for identification
Wechselbehälter - Markierung - Teil 1: Markierungen für die Identifizierung
Caisses mobiles - Marquage - Partie 1: Identification de propriétaire
Ta slovenski standard je istoveten z: prEN 13044-1
ICS:
35.240.60 Uporabniške rešitve IT v IT applications in transport
transportu in trgovini and trade
55.180.10 9HþQDPHQVNLNRQWHMQHUML General purpose containers
oSIST prEN 13044-1:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 13044-1:2009

---------------------- Page: 2 ----------------------
oSIST prEN 13044-1:2009
EUROPEAN STANDARD
DRAFT
prEN 13044-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2008
ICS 55.180.10; 35.240.60 Will supersede EN 13044:2000
English Version
Swap bodies - Marking - Part 1: Markings for identification
Caisses mobiles - Marquage - Partie 1: Marquages Wechselbehälter - Markierung - Teil 1: Markierungen für die
d'identification Identifizierung
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 119.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13044-1:2008: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 13044-1:2009
prEN 13044-1:2008 (E)
Contents Page
Foreword.3
Introduction .4
1 Scope .5
2 Normative references .5
3 Terms and definitions .6
4 Identification system and its associated marks .6
4.1 Identification system .6
4.2 Identification of the owner .6
4.3 Serial number.7
4.4 Check digit.7
5 Physical display of marks.7
5.1 Size and colour of marks .7
5.2 Layout and location of marks.7
5.2.1 General.7
5.2.2 Layout of marks .7
5.2.3 Location of marks.7
Annex A (normative) Determination of check digit .9
A.1 General.9
A.2 Numerical equivalents of ILU identification system, and serial number .9
A.3 Weighting factor.9
A.4 Modulus .9
A.5 Value of check digit .10
A.6 Example calculation of the check digit .10

2

---------------------- Page: 4 ----------------------
oSIST prEN 13044-1:2009
prEN 13044-1:2008 (E)
Foreword
This document (prEN 13044-1:2008) has been prepared by Technical Committee CEN/TC 119 “Swap bodies
for combined goods transport”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document supersedes EN 13044:2000.
3

---------------------- Page: 5 ----------------------
oSIST prEN 13044-1:2009
prEN 13044-1:2008 (E)

Introduction
This standard contains the recommended method of marking Intermodal Loading Units (ILU) to meet current
and future requirements.
The standard follows the format used in EN ISO 6346, the world wide accepted standard for marking and
coding of marine freight containers. As the above standard can be applied, without alteration, to an ILU, the
standard is not directly interchangeable with the ISO standard. However since the ILU are handled and
transported in Europe in the same environment as ISO freight containers, the two standards are compatible.
4

---------------------- Page: 6 ----------------------
oSIST prEN 13044-1:2009
prEN 13044-1:2008 (E)

1 Scope
This European Standard provides a system for the identification and presentation of information about the ILU.
The identification system is intended for general application, for example in documentation, control and
communications (including automatic data processing systems), as well as for display on an ILU and other
non ISO containers (i.e.: which dimensions and testing parameters differ from those defined by the applicable
ISO standards) used in European transport.
The methods of displaying identification and certain other data (including operational data) on swap bodies by
means of permanent marks are included.
This European Standard specifies:
a) an ILU identification system with an associated system for verifying the accuracy of its use, having
mandatory marks for the presentation of the identification system for visual interpretation, and
b) a coding system for data on ILU size and type, with corresponding marks for their display;
c) mandatory operational marks;
d) physical presentation of the marks on the
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.