SIST EN ISO 4142:2002

SLOVENSKI STANDARD
SIST EN ISO 4142:2002
01-november-2002
1DGRPHãþD
SIST ISO 4142:1998
Laboratorijska steklovina - Epruvete (ISO 4142:2002)
Laboratory glassware - Test tubes (ISO 4142:2002)
Laborgeräte aus Glas - Reagenzgläser (ISO 4142:2002)
Verrerie de laboratoire - Tubes a essais (ISO 4142:2002)
Ta slovenski standard je istoveten z: EN ISO 4142:2002
ICS:
71.040.20 Laboratorijska posoda in Laboratory ware and related
aparati apparatus
SIST EN ISO 4142:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 4142:2002

---------------------- Page: 2 ----------------------

SIST EN ISO 4142:2002
EUROPEAN STANDARD
EN ISO 4142
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2002
ICS 71.040.20
English version
Laboratory glassware - Test tubes (ISO 4142:2002)
Verrerie de laboratoire - Tubes à essais (ISO 4142:2002) Laborgeräte aus Glas - Reagenzgläser (ISO 4142:2002)
This European Standard was approved by CEN on 10 July 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4142:2002 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 4142:2002
EN ISO 4142:2002 (E)
CORRECTED  2002-10-02
Foreword
This document (EN ISO 4142:2002) has been prepared by Technical Committee ISO /TC 48
"Laboratory glassware and related apparatus" in collaboration with Technical Committee
CEN/TC 332 "Laboratory equipment", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by February 2003, and conflicting national
standards shall be withdrawn at the latest by February 2003.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,
Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the
United Kingdom.
Endorsement notice
The text of ISO 4142:2002 has been approved by CEN as EN ISO 4142:2002 without any
modifications.
2

---------------------- Page: 4 ----------------------

SIST EN ISO 4142:2002
INTERNATIONAL ISO
STANDARD 4142
Second edition
2002-08-15
Laboratory glassware — Test tubes
Verrerie de laboratoire — Tubes à essais

Reference number
ISO 4142:2002(E)
© ISO 2002

---------------------- Page: 5 ----------------------

SIST EN ISO 4142:2002
ISO 4142:2002(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be
edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file,
parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
©
ii ISO 2002 – All rights reserved

---------------------- Page: 6 ----------------------

SIST EN ISO 4142:2002
ISO 4142:2002(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 4142 was prepared by Technical Committee ISO/TC 48, Laboratory glassware and
related apparatus, Subcommittee SC 2, General laboratory glassware (other than measuring apparatus).
This second edition cancels and replaces the first edition (ISO 4142:1997) by incorporating the following changes:
a) culture tubes have been deleted;
b) the material has been more precisely specified;
c) three types of test tubes have been introduced;
d) additional series and nominal sizes have been added.
©
ISO 2002 – All rights reserved iii

---------------------- Page: 7 ----------------------

SIST EN ISO 4142:2002

---------------------- Page: 8 ----------------------

SIST EN ISO 4142:2002
INTERNATIONAL STANDARD ISO 4142:2002(E)
Laboratory glassware — Test tubes
1 Scope
This International Standard specifies a range of test tubes, suitable for general laboratory use, fabricated from
borosilicate, neutral or soda/l
...