Additive manufacturing - Test artefacts - Geometric capability assessment of additive manufacturing systems (ISO/ASTM 52902:2023)

This document covers the general description of benchmarking test piece geometries, i.e. artefacts, along with quantitative and qualitative measurements to be taken on the benchmarking test piece(s) to assess the performance of additive manufacturing (AM) systems.
This performance assessment can serve the following two purposes:
—    AM system capability evaluation;
—    AM system calibration.
The benchmarking test piece(s) is (are) primarily used to quantitatively assess the geometric performance of an AM system. This document describes a suite of test geometries, each designed to investigate one or more specific performance metrics and several example configurations of these geometries into test build(s). It prescribes quantities and qualities of the test geometries to be measured but does not dictate specific measurement methods. Various user applications can require various grades of performance. This document discusses examples of feature configurations, as well as measurement uncertainty requirements, to demonstrate low- and high-grade examination and performance. This document does not discuss a specific procedure or machine settings for manufacturing a test piece.

Additive Fertigung - Testkörper - Geometrische Leistungsbewertung additiver Fertigungssysteme (ISO/ASTM 52902:2023)

Dieses Dokument enthält die allgemeine Beschreibung von Prüfkörpergeometrien mit dem Ziel des Benchmarkings, gemeinsam mit an dem/den Benchmarking-Prüfkörper(n) vorzunehmenden quantitativen und qualitativen Messungen zur Bewertung der Leistung additiver Fertigungssysteme (AM-Systeme).
Diese Leistungsbewertung kann den beiden folgenden Zwecken dienen:
- der Fähigkeitsbewertung des AM-Systems;
- der Kalibrierung des AM-Systems.
Der Hauptverwendungszweck der/des Benchmarking-Prüfkörper(s) ist die quantitative Bewertung der geometrischen Leistungsfähigkeit eines AM-Systems. Das Dokument beschreibt einen Satz von Prüfgeometrien, die jeweils für die Untersuchung einer oder mehrerer Leistungsmetriken ausgelegt sind, sowie mehrere Beispielkonfigurationen dieser Geometrien im/in Prüfkörper(n). Es gibt zu messende Quantitäten und Qualitäten der Prüfgeometrien vor, schreibt aber keine spezifischen Messverfahren vor. Verschiedene Nutzeranwendungen können verschiedene Leistungsniveaus erfordern. Zur Veranschaulichung von Untersuchungen und für den Nachweis der Leistungsfähigkeit auf niedrigem und hohem Niveau erörtert dieses Dokument Beispiele für Merkmalskonfigurationen sowie Anforderungen an die Messunsicherheit. Dieses Dokument behandelt keine spezifischen Verfahrensweisen oder Maschineneinstellungen für die Prüfkörperherstellung.

Fabrication additive - Pièces types d'essais - Évaluation de la capacité géométrique des systèmes de fabrication additive (ISO/ASTM 52902:2023)

Le présent document couvre la description générale du benchmarking de géométries d’éprouvette, c’est-à-dire des pièces types, ainsi que les mesures quantitatives et qualitatives à appliquer à la ou aux éprouvettes de benchmarking afin d’évaluer les performances de systèmes de fabrication additive (FA).
Cette évaluation de performances peut servir aux deux fins suivantes:
—    Évaluation de la capacité du système FA;
—    Étalonnage du système FA.
La ou les éprouvettes de benchmarking sont utilisées principalement pour évaluer quantitativement les performances géométriques d’un système FA. Le présent document décrit une suite de géométries d’essai, chacune conçue pour examiner une ou plusieurs mesures de performances spécifiques, ainsi que plusieurs configurations d’exemple de ces géométries au sein d’une ou plusieurs éprouvettes. Il prescrit les quantités et qualités des géométries d’essai à mesurer, mais ne stipule pas de méthodes de mesure spécifiques. Différentes applications d’utilisateur peuvent exiger différents niveaux de performances. Le présent document donne des exemples de configurations de forme ainsi que des exigences d’incertitude de mesure afin de faire la démonstration d’un examen et de performances de niveau bas et élevé. Le présent document ne donne pas de mode opératoire ou de réglages de machine spécifiques pour la fabrication d’une éprouvette.

Aditivna proizvodnja - Preskusna telesa - Geometrijske zmogljivosti aditivnih proizvodnih sistemov (ISO/ASTM 52902:2023)

Ta dokument zajema splošen opis geometrij primerjalnih preskušancev, tj. artefaktov, skupaj s kvantitativnimi in kvalitativnimi meritvami, ki jih je treba opraviti na primerjalnih preskušancih za oceno zmogljivosti aditivnih proizvodnih (AM) sistemov.
Ta ocena zmogljivost se lahko uporablja za naslednje namene:
– ocena zmogljivosti aditivnega proizvodnega sistema;
– umerjanje aditivnega proizvodnega sistema.
Primerjalni preskušanci se v osnovi uporabljajo za kvantitativno ocenjevanje geometrijske zmogljivosti aditivnega proizvodnega sistema. Ta dokument opisuje zbirko preskusnih geometrij, od katerih je vsaka zasnovana za preiskavo ene ali več določenih meritev zmogljivosti, in več primerov konfiguracij teh geometrij v preskušancih. Predpisuje količine in kakovosti preskusnih geometrij, ki jih je treba izmeriti, ne določa pa posameznih metod meritev. Različni načini uporabe lahko zahtevajo različne razrede zmogljivosti. Ta dokument predstavlja primere konfiguracij značilnosti in tudi zahteve glede merilne negotovosti za prikaz preskusov ter zmogljivosti nizkega in visokega razreda. Ta dokument ne obravnava določenega postopka ali nastavitev stroja za proizvodnjo preskušanca.

General Information

Status
Published
Public Enquiry End Date
02-Mar-2022
Publication Date
17-Oct-2023
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
21-Sep-2023
Due Date
26-Nov-2023
Completion Date
18-Oct-2023

Relations

Buy Standard

Standard
EN ISO/ASTM 52902:2023
English language
48 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO/ASTM 52902:2022 - BARVE
English language
43 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO/ASTM 52902:2023
01-november-2023
Nadomešča:
SIST EN ISO/ASTM 52902:2019
Aditivna proizvodnja - Preskusna telesa - Geometrijske zmogljivosti aditivnih
proizvodnih sistemov (ISO/ASTM 52902:2023)
Additive manufacturing - Test artefacts - Geometric capability assessment of additive
manufacturing systems (ISO/ASTM 52902:2023)
Additive Fertigung - Testkörper - Geometrische Leistungsbewertung additiver
Fertigungssysteme (ISO/ASTM 52902:2023)
Fabrication additive - Pièces types d'essais - Évaluation de la capacité géométrique des
systèmes de fabrication additive (ISO/ASTM 52902:2023)
Ta slovenski standard je istoveten z: EN ISO/ASTM 52902:2023
ICS:
25.030 3D-tiskanje Additive manufacturing
SIST EN ISO/ASTM 52902:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO/ASTM 52902:2023

---------------------- Page: 2 ----------------------
SIST EN ISO/ASTM 52902:2023


EN ISO/ASTM 52902
EUROPEAN STANDARD

NORME EUROPÉENNE

August 2023
EUROPÄISCHE NORM
ICS 25.030 Supersedes EN ISO/ASTM 52902:2019
English Version

Additive manufacturing - Test artefacts - Geometric
capability assessment of additive manufacturing systems
(ISO/ASTM 52902:2023)
Fabrication additive - Pièces types d'essais - Évaluation Additive Fertigung - Testkörper - Geometrische
de la capacité géométrique des systèmes de fabrication Leistungsbewertung additiver Fertigungssysteme
additive (ISO/ASTM 52902:2023) (ISO/ASTM 52902:2023)
This European Standard was approved by CEN on 12 August 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO/ASTM 52902:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO/ASTM 52902:2023
EN ISO/ASTM 52902:2023 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO/ASTM 52902:2023
EN ISO/ASTM 52902:2023 (E)
European foreword
This document (EN ISO/ASTM 52902:2023) has been prepared by Technical Committee ISO/TC 261
"Additive manufacturing" in collaboration with Technical Committee CEN/TC 438 “Additive
Manufacturing” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2024, and conflicting national standards
shall be withdrawn at the latest by February 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO/ASTM 52902:2019.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement no
...

SLOVENSKI STANDARD
oSIST prEN ISO/ASTM 52902:2022
01-februar-2022
Aditivna proizvodnja - Preskusna telesa - Geometrijske zmogljivosti aditivnih
proizvodnih sistemov (ISO/ASTM DIS 52902:2021)
Additive manufacturing - Test artifacts - Geometric capability assessment of additive
manufacturing systems (ISO/ASTM DIS 52902:2021)
Additive Fertigung - Testkörper - Geometrische Leistungsbewertung additiver
Fertigungssysteme (ISO/ASTM DIS 52902:2021)
Fabrication additive - Pièces types d'essais - Évaluation de la capacité géométrique des
systèmes de fabrication additive (ISO/ASTM DIS 52902:2021)
Ta slovenski standard je istoveten z: prEN ISO/ASTM 52902
ICS:
25.030 3D-tiskanje Additive manufacturing
oSIST prEN ISO/ASTM 52902:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO/ASTM 52902:2022

---------------------- Page: 2 ----------------------
oSIST prEN ISO/ASTM 52902:2022
DRAFT INTERNATIONAL STANDARD
ISO/ASTM DIS 52902
ISO/TC 261 Secretariat: DIN
Voting begins on: Voting terminates on:
2021-12-13 2022-03-07
Additive manufacturing — Test artifacts — Geometric
capability assessment of additive manufacturing systems
Fabrication additive — Pièces types d'essai — Évaluation de la capacité géométrique des systèmes de
fabrication additive
ICS: 25.030
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/ASTM DIS 52902:2021(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO/ASTM International 2021

---------------------- Page: 3 ----------------------
oSIST prEN ISO/ASTM 52902:2022
ISO/ASTM DIS 52902:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO/ASTM International 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester. In the United States, such requests should be sent to ASTM International.
ISO copyright office ASTM International
CP 401 • Ch. de Blandonnet 8 100 Barr Harbor Drive, PO Box C700
CH-1214 Vernier, Geneva West Conshohocken, PA 19428-2959, USA
Phone: +41 22 749 01 11 Phone: +610 832 9634
Fax: +610 832 9635
Email: copyright@iso.org Email: khooper@astm.org
Website: www.iso.org Website: www.astm.org
Published in Switzerland
ii
  © ISO/ASTM International 2021 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO/ASTM 52902:2022
ISO/ASTM DIS 52902:2021(E)
Contents Page
Foreword .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Significance and use .1
4.1 General . 1
4.2 Comparing results from one machine . 2
5 General principles for pr
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.