SIST EN ISO 5261:2002

SLOVENSKI STANDARD
SIST EN ISO 5261:2002
01-februar-2002
Technical drawings - Simplified representation of bars and profile sections (ISO
5261:1995)
Technical drawings - Simplified representation of bars and profile sections (ISO
5261:1995)
Technische Zeichnungen - Vereinfachte Angabe von Stäben und Profilen (ISO
5261:1995)
Dessins techniques - Représentation simplifiée des barres et des profilés (ISO
5261:1995)
Ta slovenski standard je istoveten z: EN ISO 5261:1999
ICS:
01.080.30 *UDILþQLVLPEROL]DXSRUDERY Graphical symbols for use on
ULVEDKGLDJUDPLKQDþUWLK mechanical engineering and
]HPOMHYLGLKYVWURMQLãWYXLQ construction drawings,
JUDGEHQLãWYXWHUYXVWUH]QL diagrams, plans, maps and in
WHKQLþQLSURL]YRGQL relevant technical product
GRNXPHQWDFLML documentation
01.100.30 *UDGEHQLQDþUWL Construction drawings
SIST EN ISO 5261:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 5261:2002

---------------------- Page: 2 ----------------------

SIST EN ISO 5261:2002

---------------------- Page: 3 ----------------------

SIST EN ISO 5261:2002

---------------------- Page: 4 ----------------------

SIST EN ISO 5261:2002
INTERNATIONAL
STANDARD
Second edition
1995-l I-01
Technical drawings - Simplified
representation of bars and profile sections
- Rep&en tation simplif@e des barres et des
Dessins techniques
pro filks
Reference number
IS0 5261:1995(E)

---------------------- Page: 5 ----------------------

SIST EN ISO 5261:2002
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work
of preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission
(I EC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard IS0 5261 was prepared by Technical Committee
ISOfTC 10, Technical drawings, product definition and related documen-
tation, Subcommittee SC 6, Mechanical engineering documentation.
This second edition of IS0 5261 together with IS0 5845~I:1995 cancel
and replace IS0 5261:1981, which has been technically revised.
Annex A of this International Standard is for information only.
0 IS0 1995
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, rncluding photocopyrng and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-1211 Geneve 20 l Switzerland
Printed in Switzerland

---------------------- Page: 6 ----------------------

SIST EN ISO 5261:2002
0 IS0
IS0 5261:1995(E)
Introduction
For purposes of uniformity, the figures given in this International Standard
are shown in first angle orthographic projection and all the linear dimen-
sions are in millimetres. It is understood that other orthographic pro-
jections or units of measure could equally well have been used without
prejudice to the principles established. The figures, chosen only to illus-
trate the text, may be incomplete.
. . .
III

---------------------- Page: 7 ----------------------

SIST EN ISO 5261:2002
This page intentionally left blank

---------------------- Page: 8 ----------------------

SIST EN ISO 5261:2002
IS0 5261:1995(E)
INTERNATIONAL STANDARD 0 IS0
Technical drawings - Simplified representation of
bars and profile sections
3 Definitions
1 Scope
This International standard specifies rules comp-
For the purposes of this International Standard, the
lementary to IS0 128’) and IS0 129 for the simplified
definitions given in IS0 10209-I apply.
representation of bars and profile sections in as-
sembly and detail drawings concerning, among oth-
ers:
- structural metal work consisting of plates and
sheets, profile sections and compound elements
(including bridges, frameworks, pilings, etc.);
4 Complementary rules for the
- lifting and transport appliances;
simplified representation of bars and
- storage tanks and pressure vessels; profile sections
- lifts, moving stairways and conveyor belts.
The simplified representation of bars and profile
sections shal
...