SIST EN 60335-2-102:2016

SLOVENSKI STANDARD
SIST EN 60335-2-102:2016
01-marec-2016
1DGRPHãþD
SIST EN 60335-2-102:2007
SIST EN 60335-2-102:2007/A1:2010
*RVSRGLQMVNLLQSRGREQLHOHNWULþQLDSDUDWL9DUQRVWGHO3RVHEQH]DKWHYH
]DDSDUDWHQDSOLQROMHLQWUGQDJRULYD]HOHNWULþQLPLSULNOMXþNL
Household and similar electrical appliances - Safety - Part 2-102: Particular requirements
for gas, oil and solid-fuel burning appliances having electrical connections
Sicherheit elektrischer Geräte für den Hausgebrauch und ähnliche Zwecke - Teil 2-102:
Besondere Anforderungen für Gas-, Öl- und Festbrennstoffgeräte mit elektrischen
Anschlüssen
Appareils électrodomestiques et analogues - Sécurité - Partie 2-102: Règles particulières
pour les appareils à combustion au gaz, au mazout et à combustible solide comportant
des raccordements électriques
Ta slovenski standard je istoveten z: EN 60335-2-102:2016
ICS:
13.120 Varnost na domu Domestic safety
97.100.20 Plinski grelniki Gas heaters
97.100.30 Grelniki na trdo gorivo Solid fuel heaters
SIST EN 60335-2-102:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60335-2-102:2016

---------------------- Page: 2 ----------------------

SIST EN 60335-2-102:2016


EUROPEAN STANDARD
EN 60335-2-102

NORME EUROPÉENNE

EUROPÄISCHE NORM
January 2016
ICS 13.120; 97.100.20; 97.100.30 Supersedes EN 60335-2-102:2006
English Version
Household and similar electrical appliances - Safety -
Part 2-102: Particular requirements for gas, oil and solid-fuel
burning appliances having electrical connections
(IEC 60335-2-102:2004 , modified + A1:2008 , modified
+ A2:2012 , modified)
Appareils électrodomestiques et analogues - Sécurité - Sicherheit elektrischer Geräte für den Hausgebrauch und
Partie 2-102: Règles particulières pour les appareils à ähnliche Zwecke - Teil 2-102: Besondere Anforderungen
combustion au gaz, au mazout et à combustible solide für Gas-, Öl- und Festbrennstoffgeräte mit elektrischen
comportant des raccordements électriques Anschlüssen
(IEC 60335-2-102:2004 , modifiée + A1:2008 , modifiée (IEC 60335-2-102:2004 , modifiziert + A1:2008 , modifiziert
+ A2:2012 , modifiée) + A2:2012 , modifiziert)
This European Standard was approved by CENELEC on 2015-08-24. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any
alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 60335-2-102:2016 E

---------------------- Page: 3 ----------------------

SIST EN 60335-2-102:2016
EN 60335-2-102:2016
European foreword
This document (EN 60335-2-102:2016) consists of the text of IEC 60335-2-102:2004 + A1:2008 +
A2:2012 prepared by IEC/TC 61 "Safety of household and similar electrical appliances", together with
the common modifications prepared by CLC/TC 61, "Safety of household and similar electrical
appliances".
The following dates are fixed:
(dop) 2016-07-22
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
(dow) 2019-01-22
• latest date by which the national standards conflicting with
the document have to be withdrawn
This document supersedes EN 60335-2-102:2006.
This Part 2 has to be used in conjunction with EN 60335-1, Household and similar electrical
1)
appliances – Safety – Part 1: General requirements, and with IEC 60335-2-102, Edition 1.2, 2012-11 ,
Household and similar electrical appliances – Safety – Part 2-102: Particular requirements for gas, oil
and solid-fuel burning appliances having electrical connections.
When this standard states "addition", "modification" or "replacement", the relevant text of the
IEC 60335-2-102 is to be adapted; if the subclause is not mentioned in IEC 60335-2-102, the
corresponding subclause of Part 1 is to be adapted accordingly.
This standard is intended to be used in addition to the standards for non-electrical appliances and to
any Part 2 of EN 60335, if applicable.
NOTE 1 The following numbering system is used:
- subclauses, tables and figures that are numbered starting from 101 are additional to those in Part 1;
- unless notes are in a new subclause or involve notes in Part 1, they are numbered starting from 101,
including those in a replaced clause or subclause;
- additional annexes are lettered AA, BB, etc.;
- subclauses, notes, tables and annexes that are additional to those in the IEC standards are prefixed with the letter Z.
NOTE 2 The following print types are used:
- requirements: in roman type;
- test specifications: in italic type;
- notes: in small roman type.
Words in bold in the text are defined in Clause 3. When a definition concerns an adjective, the adjective and the
associated noun are also in bold.

1) IEC 60335-2-102, Edition 1.2, 2012-11 is the consolidated edition of IEC 60335-2-102:2004 +
A1:2008 + A2:2012.
2

---------------------- Page: 4 ----------------------

SIST EN 60335-2-102:2016
EN 60335-2-102:2016
There are no special national conditions causing a deviation from this European Standard, other than
those listed in Annex ZA to EN 60335-1.
There are no national deviations causing a deviation from this European Standard, other than those
listed in Annex ZB to EN 60335-1.
p NOTE  In this document, p is used in the margin to indicate instructions for preparing the printed version.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment
Designed for use within Certain Voltage Limits (LVD - 2006/95/EC).
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of this
document.
3

---------------------- Page: 5 ----------------------

SIST EN 60335-2-102:2016
EN 60335-2-102:2016
Endorsement notice
The text of the International Standard IEC 60335-2-102:2004 + A1:2008 + A2:2012 was approved by
CENELEC as a European Standard with agreed common modifications.
COMMON MODIFICATIONS
INTRODUCTION
p Add:
The principal objectives of the Low Voltage Directive, 2006/95/EC, are covered by this standard. The
Essential Health and Safety Requirements (EHSR) (except 1.7.4.2 u) of the Directive 2006/42/EC,
which can be applicable to some of the appliances covered by this standard, have also been taken into
account.
1 Scope
p Replace the second and third paragraphs by:
This European Standard deals with the safety of gas, oil and solid-fuel burning appliances having
electrical connections, their rated voltage being not more than 250 V for single-phase appliances and
480 V for other appliances.
This standard covers the electrical safety and some other safety aspects of these appliances. All safety
aspects of these appliances, including those relevant to the noise emitted, are only covered when the
appliance also complies with the relevant product standard for the fuel-burning appliance.
If the appliance incorporates electric heating sources, it also has to comply with the relevant Part 2 of
EN 60335.
Additional requirements for appliances and machines with moving parts and intended for commercial
use are given in Annex ZE.
p Replace the paragraph after NOTE 101 by:
NOTE Z1  Examples of appliance for household environment are appliances for typical housekeeping functions
used in the household environment and appliances for typical housekeeping functions used by non-expert users:
– in shops, offices and other similar working environments,
– in farm houses,
– by clients in hotels, motels and other residential type environments,
– in bed and breakfast type environments.
NOTE Z2  Household environment includes the dwelling and its associated buildings, the garden, etc.
4

---------------------- Page: 6 ----------------------

SIST EN 60335-2-102:2016
EN 60335-2-102:2016
p Add before Note 102:
This standard has to be applied in conjunction with the relevant standards for appliances and for
control devices. Examples are listed in Annexes ZAA and ZBB.
2 Normative references
p Add:
EN 298:2012, Automatic burner control systems for burners and appliances burning gaseous or liquid
fuels
EN 60747-5-2, Discrete semiconductor devices and integrated circuits – Part 5-2: Optoelectronic
devices - Essential ratings and characteristics (IEC 60757-5-2)
EN 61310-1, Safety of machinery – Indication, marking and actuation – Part 1: Requirements for
visual, acoustic and tactile signals (IEC 61310-1)
EN 61810-1, Electromechanical elementary relays – Part 1: General and safety requirements
(IEC 61810-1)
3 Terms and definitions
p Replace 3.106 by:
3.106
lock-out
process in which the appliance goes into one of two lock-out conditions following shut-down
3.106.Z1
non-volatile lock-out
condition following shut-down from which the appliance can only be restarted by a manual reset
3.106.Z2
volatile lock-out
condition following shut-down from which the appliance can be restarted either by a manual reset or
by an interruption of the power supply and its subsequent restoration
7 Marking and instructions
7.10 Replace the fourth paragraph by:
Devices if any, used to start/stop such operational functions of the appliance, which may cause
hazards, shall be distinguished from other manual devices by means of shape, or size, or surface
texture, or position, etc.
5

---------------------- Page: 7 ----------------------

SIST EN 60335-2-102:2016
EN 60335-2-102:2016
13 Leakage current and dielectric strength at operating temperature
p Add:
13.1 Addition:
For appliances which are assembled on site, the leakage current and electrical strength tests on the
complete appliance need not be performed if the components and sub-assemblies have been
separately tested and the interconnection is carried out in accordance with the manufacturer’s
instructions.
If the disconnection of protective impedance or radio interference filters is not possible, the limit
specified for leakage currents is to be calculated taking into account the current through those circuits
or components.
p 13.2 Replace the text of the modification by:
For gas, oil and solid-fuel burning appliances, the limit is 5 mA.
15 Moisture resistance
p Replace the text by:
This clause of Part 1 is applicable.
p 15.2 Delete the addition.
16 Leakage current and electric strength
p 16.2 Replace the text of the modification by:
For gas, oil and solid-fuel burning appliances, the limit is 5 mA.
p 16.3 Replace the text of the addition by:
Compliance of spark ignition circuits is checked by inspection and only in case of doubt by the
following test:
Spark ignition circuits or crucial parts are submitted to an endurance test under the following
conditions:
– maximum duration of switch-on given by the manufacturer (the complete switch-on duration shall
correspond with the realistic time of use);
– the relation between on/off cycles as declared by the manufacturer;
– maximum rated voltage;
– maximum ambient temperature of all parts under test.
6

---------------------- Page: 8 ----------------------

SIST EN 60335-2-102:2016
EN 60335-2-102:2016
During the test, no breakdown to other circuits or, if the limits specified in 8.101 are exceeded,
accessible surfaces shall occur. Breakdown to conductive parts which are connected to earth is
allowed if this does not result in a critical failure of circuits with safety related functions.
In case of doubt, compliance may normally be achieved by increasing the clearance at any part of the
spark ignition circuit likely to cause an unacceptable breakdown.
19 Abnormal operation
p Add:
19.2 Replace the text by:
NOTE Z101  If electrical heating elements are incorporated, the relevant Parts 2 apply.
p Add:
19.3 Replace the text by:
NOTE Z101  If electrical heating elements are incorporated, the relevant Parts 2 apply.
p Add:
19.5 Replace the text by:
NOTE Z101  If electrical heating elements are incorporated, the relevant Parts 2 apply.
p Add:
19.6 Replace the text by:
NOTE Z101  If electrical heating elements are incorporated, the relevant Parts 2 apply.
p Add:
19.9 Replace the text by:
NOTE Z101  If electrical heating elements are incorporated, the relevant Parts 2 apply.
p Add:
19.10 Replace the text by:
NOTE Z101  If electrical heating elements are incorporated, the relevant Parts 2 apply.
p 19.11.1 Modification:
In the first paragraph, replace “a) to g)” by “a) to g) and za)”.
7

---------------------- Page: 9 ----------------------

SIST EN 60335-2-102:2016
EN 60335-2-102:2016
p 19.11.2 Modification:
In the first paragraph starting with “The following fault conditions…”, add the following new fault
condition:
za) "short-circuit" and "mechanical break-down" of relay contacts in protective electronic circuits. The failure
g
modes need not be considered if components comply with footnote to Table E.1 of EN 298:2012.
p Add:
19.11.3 Modification:
In the first paragraph, replace “a) to g)” by “a) to g) and za)”.
19.11.3 Addition:
Tests are not repeated for protective electronic circuits complying with the relevant control standard
listed in Annex ZBB.
NOTE Z101  There is no need to investigate again fault behaviour of already approved fail safe systems.
p 19.13 Replace the text of the addition by:
During the tests of 19.11.4, the appliance shall either continue to operate normally or reach a safe
situation for risks concerning the fuel (shut-down, non-volatile lock-out or volatile lock-out, if this is
permitted in the relevant appliance standard, see Annex ZAA).
24 Components
p Add:
24.1 Addition:
NOTE Z101  A list of standards applicable to controls and safety devices is given in Annex ZBB.
p Add:
24.1.1 Addition:
Relays and optocouplers which ensure electrical isolation between live parts and accessible metal
parts shall comply with EN 61810-1 and EN 60747-5-2 respectively.
27 Provision for earthing
p 27.1 Replace “shall” by “may” (English version only).
Figure 6
p Replace in Part 1 “a) to g)” by “a) to g) and za)”.
8

---------------------- Page: 10 ----------------------

SIST EN 60335-2-102:2016
EN 60335-2-102:2016
Annexes
p Replace the text by:
The annexes of Part 1 are applicable except as follows:
Annex Q
(informative)

Sequence of tests for the evaluation of electronic circuits
Addition:
NOTE  Repeat testing of a protective electronic circuit is not required where the system has already been
certified to comply with published European Standards where compliance requires that the fault behaviour of the
fail-safe system be assessed on a second fault analysis basis.
Modification:
Add the following text twice in the corresponding boxes in the diagram, after “a) to g)”: “and za)”.

9

---------------------- Page: 11 ----------------------

SIST EN 60335-2-102:2016
EN 60335-2-102:2016
Annex ZC
(normative)

Normative references to international publications
with their corresponding European publications
Addition:
Publication Year Title EN/HD Year
– – Automatic burner control systems for burners EN 298 2012
and appliances burning gaseous or liquid fuels
IEC 60747-5-2 – Discrete semiconductor devices and integrated EN 60747-5-2 –
circuits –
Part 5-2: Optoelectronic devices - Essential
ratings and characteristics
EN 61310-1 –
IEC 61310-1 – Safety of machinery - Indication, marking and
actuation
Part 1: Requirements for visual, acoustic and
tactile signals
IEC 61558-2-3 – Safety of transformers, reactors, power supply EN 61558-2-3 –
units and combinations thereof -
Part 2-3: Particular requirements and tests for
ignition transformers for gas and oil burners
IEC 61810-1 – Electromechanical elementary relays - EN 61810-1 –
Part 1: General and safety requirements
– –
ISO 3808 – Road vehicles - Unscreened high-voltage
ignition cables - General specifications, test
methods and requirements

10

---------------------- Page: 12 ----------------------

SIST EN 60335-2-102:2016
EN 60335-2-102:2016
Annex ZE
(normative)

Specific additional requirements for appliances and
machines with moving parts and intended for commercial use
p Annex ZE of Part 1 is applicable with the following modifications:
Introduction
For the verification of compliance of appliances or machines intended for commercial use with the
Essential Health and Safety Requirements (EHSR) of the Directive 2006/42/EC, the requirements in
this Annex ZE shall apply.
1 Scope
This annex specifies additional requirements concerning appliances and machines intended to be used
by expert or trained users in shops, in light industry and on farms, and appliances and machines which
are declared to be for commercial use by lay persons.
EXAMPLES  Examples of appliances within the scope of this amendment:
– commercial heating appliances
– commercial laundry and cleaning appliances
– commercial air heating systems
Some requirements of this annex may be superseded if, for a specific hazard, specific requirements
are given in the relevant fuel appliance standard.
3 Terms and definitions
This clause of Annex ZE of Part 1 is applicable.
4 General requirements
This clause of Annex ZE of Part 1 is applicable.
7 Marking and instructions
7.12.ZE1 The sixth dashed item is not applicable.
11

---------------------- Page: 13 ----------------------

SIST EN 60335-2-102:2016
EN 60335-2-102:2016
20 Stability and mechanical hazards
This clause of Annex ZE of Part 1 is applicable except as follows:
20.1 Replace the second paragraph by:
Compliance is checked by inspection and the relevant tests as specified in the relevant appliance
standard for the fuel-burning appliance. If the appliance incorporates electric heating sources, it has
also to comply with the relevant Part 2 of EN 60335.
20.2 Add after the second dashed item:
In case it is not possible for technical reasons to provide a guard, adequate warnings according to
EN 61310-1 shall be provided to the appliance.
EXAMPLES  Mechanical fuel/air ratio controls, air damper flap.
21 Mechanical strength
This clause of Annex ZE of Part 1 is applicable.
22 Construction
This clause of Annex ZE of Part 1 is applicable.
12

---------------------- Page: 14 ----------------------

SIST EN 60335-2-102:2016
EN 60335-2-102:2016
Annex ZAA
(informative)

Standards for non-electric appliances
The following table gives a list of examples of standards for non-electric appliances to which this
standard may apply.
Table ZAA.1
Energy EN reference Appliance
Gas EN 26 Appliances for instantaneous production of hot water
EN 30 Domestic cooking appliances
EN 89 Storage water heaters for sanitary use
EN 203 Catering equipment - safety requirements
EN 303-3 Central heating boilers
EN 484 LPG fired independent hotplates
EN 497 LPG fired boiling burners
EN 498 LPG fired barbecues for outdoor use
EN 509 Decorative fuel effect gas appliances
EN 525 Forced convection air heaters
EN 613 Independent convection heaters
EN 621 Convection air heaters for space heating without fan, ≤ 300 kW
EN 656
Central heating boilers, > 70 kW ≤ 300 kW
EN 676 Gas burners using fans
EN 732 Absorption refrigerating appliances using LPG
EN 777 Radiant tube heaters systems for non-domestic use
EN 778
Convection air heaters for space heating without fan, ≤ 70 kW
EN 1020
Convection air heaters for space heating with fan, ≤ 300 kW
EN 1266 Convection air heaters incorporating a fan
EN 1458 Tumble dryers
EN 13836 Central heating boilers, > 300 kW ≤ 1000 kW
EN 15502-2-1 Gas-fired central heating boilers - Part 2-1: Specific standard for type C
appliances and type B2, B3 and B5 appliances of a nominal heat input not
exceeding 1 000 kW
EN 15502-2-2 Gas-fired central heating boilers - Part 2-2: Specific standard for type B1
appliances
EN 50465 Gas appliances - Combined heat and power appliance of nominal heat input
inferior or equal to 70 kW
Oil EN 1 Fluid oil stoves with vaporizing burners
EN 303-1 Central heating boilers
Solid fuel EN 303-5 Central heating boilers
13

---------------------- Page: 15 ----------------------

SIST EN 60335-2-102:2016
EN 60335-2-102:2016
Annex ZBB
(informative)

Standards for control and safety devices
The following table gives a list of examples of standards for control and safety devices.
Table ZBB.1
Energy EN reference Device
Gas EN 125 Thermoelectric flame failure devices
EN 126 Multifunctional controls for gas burning appliances
EN 161 Automatic shut-off valves for gas burners
EN 298 Automatic gas burner control units for gas burners
EN 1643 Gas valve proving systems
 EN 1854 Air/gas pressure switches
EN 12067-2 Gas/air ratio controls for gas burning appliances
EN 13611 Safety and control devices for gas-burning appliances
Oil EN 298 Automatic burner control systems for burners and appliances burning
gaseous or liquid fuels
ISO 23553-1 Safety and control devices for oil burners and oil-burning appliances -
Particular requirements - Part 1: Automatic and semi-automatic valves
Gas, oil, EN 60730-1 Automatic electrical controls for household and similar use
solid fuel Part 1: General requirements
 EN 60730-2-2 Thermal motor protectors
EN 60730-2-5 Automatic electrical burner control systems
EN 60730-2-6 Automatic electrical pressure sensing controls
EN 60730-2-7 Timers and time switches
EN 60730-2-8 Electrically operated water valves
EN 60730-2-9 Temperature sensing controls
EN 60730-2-10 Motor starting relays
EN 60730-2-11 Energy regulators
EN 60730-2-12 Electrically operated door locks
EN 60730-2-14 Electric actuators
EN 60730-2-19 Oil valves
14

---------------------- Page: 16 ----------------------

SIST EN 60335-2-102:2016
EN 60335-2-102:2016
Annex ZZ
(informative)

Coverage of Essential Requirements of EU Directives
p The Annex ZZ of Part 1 is replaced by:
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers all
relevant essential requirements of the EC Directive 2006/42/EC except all essential requirements
concerning noise, as given in Annex I of the EC Directive 2006/42/EC.
Compliance with this standard provides one means of conformity with the specified essential
requirements of the Directive concerned.
WARNING: Other requirements and other EU Directives may be applicable to the products falling
within the scope of this standard.
15

---------------------- Page: 17 ----------------------

SIST EN 60335-2-102:2016
EN 60335-2-102:2016
Bibliography
p Add the following note to the standard mentioned:

ISO 13732-1 NOTE Harmonized as EN 13732-1.

p Add the following standards:
EN ISO 14121-1, Safety of machinery – Risk assessment – Part 1: Principles (ISO 14121-1)
EN ISO 12100:2010, Safety of machinery – General principles for design – Risk assessment and risk
reduction (ISO 12100:2010)

16

---------------------- Page: 18 ----------------------

SIST EN 60335-2-102:2016



IEC 60335-2-102

®


Edition 1.2 2012-11




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Household and similar electrical appliances – Safety –

Part 2-102: Particular requirements for gas, oil and solid-fuel burning appliances

having electrical connections




Appareils électrodomestiques et analogues – Sécurité –

Partie 2-102: Règles particulières pour les appareils à combustion au gaz, au


mazout et à combustible solide comportant des raccordements électriques













INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX CF


ICS 13.120; 97.100.20; 97.100.30 ISBN 978-2-8322-0482-5



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 19 ----------------------

SIST EN 60335-2-102:2016
– 2 – 60335-2-102  IEC:2004+A1:2008
+A2:2012


CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 7
2
3 Terms and definitions . 7
4 General requirement . 7
5 General conditions for the tests . 7
6 Classification . 8
7 Marking and instructions . 8
8 Protection against access to live parts . 8
9 Starting of motor-operated appliances . 9
10 Power input and current . 9
11 Heating . 9
12 Void . 9
13 Leakage current and dielectric strength at operating temperature . 9
14 Transient overvoltages . 9
15 Moisture resistance . 9
16 Leakage current and electric strength . 10
17 Overload protection of transformers and associated circuits . 10
18 Endurance . 10
19 Abnormal operation . 11
20 Stability and mechanical hazards . 11
21 Mechanical strength . 11
22 Construction . 11
23 Internal wiring . 13
24 Components . 13
25 Supply connection and external flexible cords . 13
26 Terminals for external connections . 13
27 Provision for earthing .
...