SIST EN 2606:2009
(Main)Aerospace series - 60° interface for adaptors, threaded, with lockring - Geometric configuration
Aerospace series - 60° interface for adaptors, threaded, with lockring - Geometric configuration
This standard specifies the dimensional characteristics of the 60° interface for adaptors, threaded, with lockring, assembly with elastomer O-ring, for aerospace applications. This standard applies to all adaptors, threaded, with lockring, assembled to EN 2607 and used in fluid systems with a nominal pressure of 28 000 kPa for which a metric-size coupling with a 60° conical sealing surface has been selected.
Luft- und Raumfahrt - 60°-Anschlusszapfen für gerade Einschraubverschraubungen mit Sicherungsring - Konstruktionsblatt
Diese Norm legt die Maße von 60°-Anschlusszapfen für gerade Einschraubverschraubungen mit
Sicherungsring und Elastomer-O-Ring zur Verwendung in der Luft- und Raumfahrt fest.
Diese Norm gilt für alle geraden Einschraubverschraubungen mit Sicherungsring, die nach EN 2607
aufgebaut sind und in Hydraulikanlagen mit 28 000 kPa Höchstdruck verwendet werden, für die eine
metrische Verschraubung mit 60°-Konus-Dichtfläche gewählt wurde.
Série aérospatiale - Raccords avec cône d'étanchéité 60° pour raccords droits, filetés, avec bague de sécurité - Configuration géométrique
Aeronavtika - Vmesnik 60° za adapterje, z navojem, z zaklepnim obročkom - Geometrijski načrt
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - 60°-Anschlusszapfen für gerade Einschraubverschraubungen mit Sicherungsring - KonstruktionsblattSérie aérospatiale - Raccords avec cône d'étanchéité 60° pour raccords droits, filetés, avec bague de sécurité - Configuration géométriqueAerospace series - 60° interface for adaptors, threaded, with lockring - Geometric configuration49.030.20Sorniki, vijaki, stebelni vijakiBolts, screws, studsICS:Ta slovenski standard je istoveten z:EN 2606:2009SIST EN 2606:2009en01-oktober-2009SIST EN 2606:2009SLOVENSKI
STANDARD
SIST EN 2606:2009
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 2606
July 2009 ICS 49.030.20 English Version
Aerospace series - 60° interface for adaptors, threaded, with lockring - Geometric configuration
Série aérospatiale - Raccords avec cône d'étanchéité 60° pour raccords droits, filetés, avec bague de sécurité - Configuration géométrique
Luft- und Raumfahrt - 60°-Anschlusszapfen für gerade Einschraubverschraubungen mit Sicherungsring - Konstruktionsblatt This European Standard was approved by CEN on 13 June 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2606:2009: ESIST EN 2606:2009
EN 2606:2009 (E) 2 Contents Page Foreword .3 1 Scope .4 2 Normative references .4 3 Required characteristics .4 4 Designation .7
SIST EN 2606:2009
EN 2606:2009 (E) 3 Foreword This document (EN 2606:2009) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2010, and conflicting national standards shall be withdrawn at the latest by January 2010. Attention is drawn to the possibility that some of the elements of this doc
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.