oSIST prEN ISO/ASTM 52908:2022

SLOVENSKI STANDARD
oSIST prEN ISO/ASTM 52908:2022
01-marec-2022
[Not translated]
Additive manufacturing of metals - Finished Part properties - Post-processing, inspection
and testing of parts produced by powder bed fusion (ISO/ASTM DIS 52908:2022)
Additive Fertigung von Metallen - Eigenschaften von Fertigteilen - Nachbearbeitung,
Inspektion und Prüfung von Bauteilen hergestellt mittels pulverbettbasiertem Schmelzen
(ISO/ASTM DIS 52908:2022)
Fabrication additive de métaux - Propriétés des pièces finies - Post-traitement,
inspection et essais des pièces produites par fusion sur lit de poudre (ISO/ASTM DIS
52908:2022)
Ta slovenski standard je istoveten z: prEN ISO/ASTM 52908
ICS:
25.030 3D-tiskanje Additive manufacturing
oSIST prEN ISO/ASTM 52908:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO/ASTM 52908:2022

---------------------- Page: 2 ----------------------
oSIST prEN ISO/ASTM 52908:2022
DRAFT INTERNATIONAL STANDARD
ISO/ASTM DIS 52908
ISO/TC 261 Secretariat: DIN
Voting begins on: Voting terminates on:
2022-01-14 2022-04-08
Additive manufacturing of metals — Finished Part
properties — Post-processing, inspection and testing of
parts produced by powder bed fusion
ICS: 25.030
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/ASTM DIS 52908:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO/ASTM International 2022

---------------------- Page: 3 ----------------------
oSIST prEN ISO/ASTM 52908:2022
ISO/ASTM DIS 52908:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO/ASTM International 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester. In the United States, such requests should be sent to ASTM International.
ISO copyright office ASTM International
CP 401 • Ch. de Blandonnet 8 100 Barr Harbor Drive, PO Box C700
CH-1214 Vernier, Geneva West Conshohocken, PA 19428-2959, USA
Phone: +41 22 749 01 11 Phone: +610 832 9634
Fax: +610 832 9635
Email: copyright@iso.org Email: khooper@astm.org
Website: www.iso.org Website: www.astm.org
Published in Switzerland
ii
  © ISO/ASTM International 2022 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO/ASTM 52908:2022
ISO/ASTM DIS 52908:2022(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and abbreviations .2
4.1 Symbols . 2
4.2 Abbreviations .
...