SIST EN ISO 8469:2013
(Main)Small craft - Non-fire-resistant fuel hoses (ISO 8469:2013)
Small craft - Non-fire-resistant fuel hoses (ISO 8469:2013)
This International Standard specifies general requirements and physical tests for non-fire-resistant hoses for conveying petrol or petrol blended with ethanol and diesel fuel or diesel fuel blended with FAME, designed for a working pressure not exceeding 0,34 MPa for hoses with inner diameter up to and including 10 mm and 0,25 MPa for hoses up to 63 mm inner diameter in craft of hull length up to 24 m. It applies to hoses for small craft with permanently installed fuel systems. Specifications for fire-resistant hoses are given in ISO 7840[1]. Specifications for permanently installed fuel systems are given in ISO 10088.
Kleine Wasserfahrzeuge - Nicht feuerstandsfähige Kraftstoffschläuche (ISO 8469:2013)
Diese Internationale Norm legt die allgemeinen Anforderungen und physikalischen Prüfungen für nicht feuerwiderstandsfähige Schläuche fest, die als Benzin- und Dieselleitungen eingesetzt werden. Dabei sind Schläuche mit Innendurchmesser bis einschließlich 10 mm für Betriebsüberdrücke bis maximal 0,34 MPa ausgelegt und Schläuche mit größerem Innendurchmesser für Betriebsüberdrücke bis maximal 0,25 MPa für Wasserfahrzeuge mit einer Rumpflänge bis 24 m.
Sie gilt für Schläuche auf kleinen Wasserfahrzeugen mit fest eingebauten Kraftstoffsystemen.
Festlegungen für feuerwiderstandsfähige Schläuche sind in ISO 7840 ) enthalten. Festlegungen für fest eingebaute Kraftstoffsysteme sind in ISO 10088 enthalten.
Petits navires - Tuyaux souples pour carburant non résistants au feu (ISO 8469:2013)
L'ISO 8469:2013 spécifie les exigences générales et les essais physiques relatifs aux tuyaux souples non résistants au feu pour le transport d'essence ou de mélanges essence/éthanol et de carburant diesel ou de mélanges diesel/esters méthyliques d'acide gras (EMAG), conçus pour une pression de service n'excédant pas 0,34 MPa pour les tuyaux de diamètre intérieur nominal inférieur ou égal à 10 mm, et 0,25 MPa pour les tuyaux de diamètre intérieur allant jusqu'à 63 mm, installés sur les bateaux dont la longueur de coque est inférieure ou égale à 24 m
Elle s'applique aux tuyaux souples destinés aux petits navires dont le système à carburant est installé à demeure.
Les spécifications applicables aux tuyaux à carburant résistants au feu figurent dans l'ISO 7840. Les spécifications pour les systèmes carburant installés à demeure sont données dans l'ISO 10088.
Mala plovila - Gorljive cevi za gorivo (ISO 8469:2013)
Ta mednarodni standard določa splošne zahteve in fizične preskuse za gorljive cevi za pretakanje bencinskega goriva ali mešanice bencinskega goriva, etanola in dizelskega goriva ali mešanice dizelskega goriva in metilnih estrov maščobnih kislin (FAME), ki so zasnovane za uporabo pri delovnem tlaku največ 0,34 MPa za cevi z notranjim premerom največ 10 mm ter 0,25 MPa za cevi z notranjim premerom največ 63 mm v plovilu z dolžino trupa do 24 m. Uporablja se za cevi za mala plovila s trajno vgrajenim sistemom za gorivo. Specifikacije za negorljive cevi so podane v standardu ISO 7840[1]. Specifikacije za trajno vgrajene sisteme za gorivo so podane v standardu ISO 10088.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 8469:2013
01-oktober-2013
1DGRPHãþD
SIST EN ISO 8469:2007
Mala plovila - Gorljive cevi za gorivo (ISO 8469:2013)
Small craft - Non-fire-resistant fuel hoses (ISO 8469:2013)
Kleine Wasserfahrzeuge - Nicht feuerstandsfähige Kraftstoffschläuche (ISO 8469:2013)
Petits navires - Tuyaux souples pour carburant non résistants au feu (ISO 8469:2013)
Ta slovenski standard je istoveten z: EN ISO 8469:2013
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
47.020.30 Sistemi cevi Piping systems
47.080 ýROQL Small craft
SIST EN ISO 8469:2013 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 8469:2013
---------------------- Page: 2 ----------------------
SIST EN ISO 8469:2013
EUROPEAN STANDARD
EN ISO 8469
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2013
ICS 47.080 Supersedes EN ISO 8469:2006
English Version
Small craft - Non-fire-resistant fuel hoses (ISO 8469:2013)
Petits navires - Tuyaux souples pour carburant non Kleine Wasserfahrzeuge - Nicht feuerwiderstandsfähige
résistants au feu (ISO 8469:2013) Kraftstoffschläuche (ISO 8469:2013)
This European Standard was approved by CEN on 8 June 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8469:2013: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 8469:2013
EN ISO 8469:2013 (E)
Contents Page
Foreword .3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 94/25/EC as amended by Directive 2003/44/EC .4
2
---------------------- Page: 4 ----------------------
SIST EN ISO 8469:2013
EN ISO 8469:2013 (E)
Foreword
This document (EN ISO 8469:2013) has been prepared by Technical Committee ISO/TC 188 “Small craft”.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2014, and conflicting national standards shall be withdrawn at
the latest by January 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8469:2006.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive.
For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 8469:2013 has been approved by CEN as EN ISO 8469:2013 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 8469:2013
EN ISO 8469:2013 (E)
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 94/25/EC as amended by Directive
2003/44/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide one means of conforming to Essential Requirements of
the New Approach Directive 94/25/EC as amended by Directive 2003/44/EC.
Once this standard is cited in the Official Journal of the European Union under that Directive and has been
implemented as a national standard in at least one Member State, compliance with the normative clauses of
this standard given in Table ZA.1 confers, within the limits of the scope of this standard, a presumption of
conformity with the corresponding Essential Requirements of that Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this Standard and EU Directive 94/25/EC as amended by
Directive 2003/44/EC
Clause(s)/sub-clause(s) of this Essential Requirements (ERs) Qualifying
standard of EU Directive 94/25/EC as remarks/Notes
amended by Directive l_large>
2003/44/EC
All clauses Annex I A, Clause 5.2.1, Fuel This standard is relevant only in
system, General respect of fuel filling lines and
fuel vent lines installed outside
Annex I A, Clause 5.6.1, Fire
the engine compartment.
protection, General
It is also suitable for petrol
Annex II, Components, 4
distribution and return hoses
installed entirely within the
splash well and connected to an
outboard engine.
WARNING — Other requirements and other EU Directives may be applicable to the product(s) falling within
the scope of this standard.
4
---------------------- Page: 6 ----------------------
SIST EN ISO 8469:2013
INTERNATIONAL ISO
STANDARD 8469
Third edition
2013-07-15
Small craft — Non-fire-resistant fuel
hoses
Petits navires — Tuyaux souples pour carburant non résistants au feu
Reference number
ISO 8469:2013(E)
©
ISO 2013
---------------------- Page: 7 ----------------------
SIST EN ISO 8469:2013
ISO 8469:2013(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 8469:2013
ISO 8469:2013(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 General requirements . 1
4 Hose inner diameter . 1
5 Physical tests on finished hose . 2
5.1 General . 2
5.2 Test liquids. 2
5.3 Bursting pressure . 2
5.4 Vacuum collapse test . 3
5.5 Volume change in test liquids. 3
5.6 Mass reduction of test hose. 3
5.7 Effect of ozone . 3
5.8 Fuel permeation . 3
5.9 Cold flex test . 4
5.10 Abrasion test — 38 mm inner diameter and larger fuel fill hose with embedded
wire reinforcement. 4
5.11 Dry heat resistance test . 4
5.12 Oil resistance test . 4
5.13 Adhesion test . 4
6 Marking . 4
Annex A (normative) Fuel permeation test (or equivalent test method) . 6
Bibliography . 8
© ISO 2013 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 8469:2013
ISO 8469:2013(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.