SIST-TP CEN/TR 1046:2014

Oznaka standarda: SIST-TP CEN/TR 1046:2014
Koda projekta: 00155778
Organizacija: SIST
Naslov (angleški): Thermoplastics piping and ducting systems - Systems outside building structures for the conveyance of water or sewage - Practices for underground installation
Naslov (slovenski): Cevni in kanalski sistemi iz plastomernih materialov - Sistemi zunaj stavb za transport vode ali kanalizacije - Postopki za vgradnjo pod zemljo
Če kupite standardizacijski dokument v .pdf formatu prek spletne prodaje, vam nudimo 20% popust pri spodnji ceni brez DDV. Cenik SIST
Dokumenti
Ime Jezik Status Cena Dodaj v košarico
SIST-TP CEN/TR 1046:2014 angleški jezik Active SIST-I: 78.10 EUR
PDF
Papir
Tehnični odbor: PCV - Polimerne cevi, fitingi in ventili
ICS: 23.040.03 93.025 93.030
Status: Objavljen
Objavljen: 01-feb-2014
Refer. št. objave: Sporocila 2014-02
Področje projekta (angleško): This Technical Report is applicable to the installation of thermoplastics piping systems to be used for the conveyance of water or sewage under gravity and pressure conditions underground. It is intended to be used for pipes of nominal size up to and including DN 1600. Wherever the term “pipe” is used in this Technical Report, it also serves to cover any “fittings”, “ancillary” products and “components” if not otherwise specified. NOTE 1 This document does not apply to pipelines for gas supply (see EN 12007–2, Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 2: Specific functional requirements for polyethylene (MOP up to and including 10 bar). NOTE 2 It is assumed that additional recommendations and/or requirements are detailed in the individual materials voluntary product standards. Instances where this is expected to apply include those indicated in this Technical Report as follows: a) any special transportation requirements (see 5.2); b) maximum storage height (see 5.2 and 5.4); c) maximum storage period in direct sunlight (see 5.4); d) any climatic conditions requiring special storage (see 5.4); e) limiting initial and/or long-term deflections (see 6.1.1 and 6.1.2); f) information on mole ploughing and boring (see and 6.2), if applicable; g) selection of appropriate jointing system (see Clause 7); h) recommended radii of curvature for cold bending (see 8.1); i) permitted rates of loss of water under test (see 9.2.1); j) if applicable the relationship between SDR and stiffness. Requirements and instructions concerning commissioning of systems can be found in EN 805 and EN 1610 and the relevant national and/or local regulations.
Povezava na standarde
Povezava Ime Datum
Nadomešča SIST ENV 1401-3:2002 - Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo - Nemehčan polivinilklorid (PVC-U) - 3. del: Navodilo za vgradnjo 01-feb-2014
Nadomešča SIST-TS CEN/TS 14758-3:2006 - Cevni sistemi iz polimernih materialov za odvodnjavanje in kanalizacijo, ki delujejo po težnostnem principu - Polipropilen z mineralnimi modifikatorji (PP-MD) - 3. del: Smernice za polaganje 01-feb-2014
Nadomešča SIST ENV 1046:2002 - Cevni sistemi iz polimernih materialov - Sistemi zunaj stavb za transport vode ali kanalizacije - Postopki za vgradnjo nad zemljo in pod njo 01-feb-2014
Nadomešča SIST-TS CEN/TS 1852-3:2003/A1:2005 - Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo – Polipropilen (PP) – 3. del: Smernice za polaganje 01-feb-2014
Nadomešča SIST-TS CEN/TS 1852-3:2003 - Cevni sistemi iz polimernih materialov za odvodnjavanje in kanalizacijo, položeni v zemljo – Polipropilen (PP) - 3. del: Smernice za polaganje 01-feb-2014


• Slovenski standardi SIST s cenovnim razredom AC so popravki standardov in so v večini primerov brezplačni.

• Slovenski standardi SIST s cenovnim razredom AP so privzeti tuji standardi, katerih sestavni del je izvirni standard, ki ga moramo pridobiti pri izdajatelju v tujini. Naročilo pošljite na: prodaja@sist.si.

Najbolje prodajani standardi