Conveyor belts - Adhesion between constitutive elements - Test methods (ISO 252:2007)

This International Standard specifies two test methods, A and B, for determining the adhesion strength between constitutive elements of a conveyor belt, i.e. between plies and between covers and carcass. Basic test conditions are in conformity with ISO 36. It is applicable to all types of construction of conveyor belting with the exception of belts containing steel cord reinforcement, and textile-reinforced belts with a full-thickness tensile strength of less than 160 N/mm. It is not suitable or valid for light conveyor belts as described in ISO 21183-1.

Fördergurte - Lagenhaftung zwischen den Bestandteilen - Prüfverfahren (ISO 252:2007)

Diese Norm legt zwei Prüfverfahren A und B zur Bestimmung des Trennwiderstands zwischen den Lagen sowie zwischen den Deckplatten und der Karkasse von Fördergurten fest. Die wesentlichen Bedingungen der Prüfung entsprechen ISO 36.
Die Norm ist auf alle Arten von Fördergurten anwendbar, mit Ausnahme von Gurten mit Stahlseileinlagen und von Gurten mit Textileinlage, deren Nennbruchkraft weniger als 160 N/mm beträgt. Sie ist nicht anwendbar oder gültig für leichte Fördergurte nach ISO 21183-1.
ANMERKUNG  Verfahren A oder Verfahren B können alter¬nativ angewendet werden, aber die berechneten Mittel¬werte für die Haftfestigkeit können für Verfahren A und Verfahren B unterschiedlich sein. Da auch beide Verfah¬ren nicht gleichwertig anwendbar sind für alle Gurtkon¬struktionen, sollte der Rat des Gurtherstellers eingeholt werden.

Courroies transporteuses - Adhérence entre éléments constitutifs - Méthodes d'essai (ISO 252:2007)

L'ISO 252:2007 spécifie deux méthodes d'essai, A et B, permettant de déterminer l'adhérence entre éléments constitutifs d'une courroie transporteuse, c'est-à-dire entre plis et entre revêtements et carcasse. Les conditions générales d'essai sont conformes à l'ISO 36.
Elle s'applique à tous types de construction de courroie transporteuse à l'exception des courroies à armature en câble d'acier, et des courroies à armature textile présentant une résistance à la rupture inférieure à 160 N/mm. Elle n'est pas applicable ou valable pour les courroies transporteuses légères décrites dans l'ISO 21183-1.

Naprave za kontinuirni transport - Trakovi tračnih transporterjev - Sprijetost osnovnih sestavnih elementov - Preskusne metode (ISO 252:2007)

General Information

Status
Withdrawn
Publication Date
10-Mar-2008
Withdrawal Date
15-Aug-2023
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
11-Aug-2023
Due Date
03-Sep-2023
Completion Date
16-Aug-2023

Relations

Buy Standard

Standard
EN ISO 252:2008
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 252:2005
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 252:2008
01-maj-2008
1DSUDYH]DNRQWLQXLUQLWUDQVSRUW7UDNRYLWUDþQLKWUDQVSRUWHUMHY6SULMHWRVW
RVQRYQLKVHVWDYQLKHOHPHQWRY3UHVNXVQHPHWRGH ,62
Conveyor belts - Adhesion between constitutive elements - Test methods (ISO
252:2007)
Fördergurte - Lagenhaftung zwischen den Bestandteilen - Prüfverfahren (ISO 252:2007)
Courroies transporteuses - Adhérence entre éléments constitutifs - Méthodes d'essai
(ISO 252:2007)
Ta slovenski standard je istoveten z: EN ISO 252:2007
ICS:
53.040.20
SIST EN ISO 252:2008 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN ISO 252
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2007
ICS 53.040.20 Supersedes EN ISO 252-1:1999
English Version
Conveyor belts - Adhesion between constitutive elements - Test
methods (ISO 252:2007)
Courroies transporteuses - Adhérence entre éléments Fördergurte - Lagenhaftung zwischen den Bestandteilen -
constitutifs - Méthodes d'essai (ISO 252:2007) Prüfverfahren (ISO 252:2007)
This European Standard was approved by CEN on 23 May 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 252:2007: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN ISO 252:2007 (E)





Foreword


This document (EN ISO 252:2007) has been prepared by Technical Committee ISO/TC 41
"Pulleys and belts (including veebelts)" in collaboration with Technical Committee CEN/TC 188
"Conveyor belts", the secretariat of which is held by BSI.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by December 2007, and conflicting national
standards shall be withdrawn at the latest by December 2007.

This document supersedes EN ISO 252-1:1999.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United
Kingdom.


Endorsement notice

The text of ISO 252:2007 has been approved by CEN as EN ISO 252:2007 without any
modifications.

2

---------------------- Page: 3 ----------------------

INTERNATIONAL ISO
STANDARD 252
Third edition
2007-06-15


Conveyor belts — Adhesion between
constitutive elements — Test methods
Courroies transporteuses — Adhérence entre éléments constitutifs —
Méthodes d'essai




Reference number
ISO 252:2007(E)
©
ISO 2007

---------------------- Page: 4 ----------------------

ISO 252:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2007 – All rights reserved

---------------------- Page: 5 ----------------------

ISO 252:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 252 was prepared by Technical Committee ISO/TC 41, Pulleys and belts (including veebelts),
Subcommittee SC 3, Conveyor belts.
This third edition of ISO 252 cancels and replaces ISO 252-1:1999, of which it constitutes a technical revision.
It also incorporates the Technical Corrigendum, ISO 252-1:1999/Cor. 1:2006.

© ISO 2007 – All rights reserved iii

---------------------- Page: 6 ----------------------

INTERNATIONAL STANDARD ISO 252:2007(E)

Conveyor belts — Adhesion between constitutive elements —
Test methods
1 Scope
This International Standard specifies two test methods, A and B, for determining the adhesion strength
between constitutive elements of a conveyor belt, i.e. between plies and between covers and carcass. Basic
test conditions are in conformity with ISO 36.
It is applicable to all types of construction of conveyor belting with the exception of belts containing steel cord
reinforcement, and textile-reinforced belts with a full-thickness tensile strength of less than 160 N/mm. It is not
[1]
suitable or valid for light conveyor belts as described in ISO 21183-1 .
NOTE Meth
...

SLOVENSKI oSIST prEN ISO 252:2005

PREDSTANDARD
maj 2005
Naprave za kontinuirni transport - Trakovi tračnih transporterjev - Sprijetost
osnovnih sestavnih elementov – Preskusne metode in zahteve (ISO/DIS
252:2005)
Conveyor belts - Ply adhesion between constitutive elements - Test method and
requirements (ISO/DIS 252:2005)
ICS 53.040.20 Referenčna številka
oSIST prEN ISO 252:2005(en)
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
DRAFT
prEN ISO 252
NORME EUROPÉENNE

EUROPÄISCHE NORM

February 2005
ICS Will supersede EN ISO 252-1:1999
English version
Conveyor belts - Ply adhesion between constitutive elements -
Test method and requirements (ISO/DIS 252:2005)
Courroies transporteuses - Adhérence entre plis entre
éléments constitutifs - Méthodes d'essai (ISO/DIS
252:2005)
This draft European Standard is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee
CEN/TC 188.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN ISO 252:2005: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------
prEN ISO 252:2005 (E)




Foreword

This document (prEN ISO 252:2005) has been prepared by Technical Committee ISO/TC 41
"Pulleys and belts (including veebelts)" in collaboration with Technical Committee CEN/TC
188 "Conveyor belts", the secretariat of which is held by BSI.

This document is currently submitted to the parallel Enquiry.

This document will supersede EN ISO 252-1:1999.


Endorsement notice

The text of ISO 252:2005 has been approved by CEN as prEN ISO 252:2005 without any
modifications.

2

---------------------- Page: 3 ----------------------
DRAFT INTERNATIONAL STANDARD ISO/DIS 252
ISO/TC 41/SC 3 Secretariat: BSI
Voting begins on: Voting terminates on:
2005-02-03 2005-07-03
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Conveyor belts — Ply adhesion between constitutive
elements — Test methods
Courroies transporteuses — Adhérence entre plis entre éléments constitutifs — Méthodes d'essai
[Revision of second edition (ISO 252:1988) and ISO 252-1:1999]
ICS 53.040.20

ISO/CEN PARALLEL ENQUIRY
The CEN Secretary-General has advised the ISO Secretary-General that this ISO/DIS covers a subject
of interest to European standardization. In accordance with the ISO-lead mode of collaboration as
defined in the Vienna Agreement, consultation on this ISO/DIS has the same effect for CEN
members as would a CEN enquiry on a draft European Standard. Should this draft be accepted, a
final draft, established on the basis of comments received, will be submitted to a parallel two-month FDIS
vote in ISO and formal vote in CEN.
To expedite distribution, this document is circulated as received from the committee secretariat.
ISO Central Secretariat work of editing and text composition will be undertaken at publication
stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
© International Organization for Standardization, 2005

---------------------- Page: 4 ----------------------
ISO/DIS 252
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user's country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying,
recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
©
ii ISO 2005 – All rights reserved

---------------------- Page: 5 ----------------------
ISO/DIS 252
Contents Page
Foreword. v
1 Scope. 1
2 Normative references. 1
3 Principle. 1
4 Apparatus. 1
5 Test pieces. 2
5.1 Time between manufacture and test. 2
5.2 Shape and dimensions. 2
5.3 Number. 2
5.4 Selection of test pieces from the sample . 2
5.5 Conditioning. 2
6 Procedure. 2
6.1 Method A (see Figure 2). 2
6.2 Method B (see Figure 3). 3

7 Expression of results . 3
7.1 Examination of traces for longitudinal test pieces .3
7.2 Examination of traces for transverse test pieces .3
8 Test report. 3
Bibliography . 8

© ISO 2005 – All rights reserved iii

---------------------- Page: 6 ----------------------
ISO/DIS 252
Foreword
ISO (the International Organ
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.