SIST-TS CEN ISO/TS 80004-1:2015

SLOVENSKI STANDARD
SIST-TS CEN ISO/TS 80004-1:2015
01-februar-2015
Nanotehnologije - Slovar - 1. del: Temeljni izrazi (ISO/TS 80004-1:2010)
Nanotechnologies - Vocabulary - Part 1: Core terms (ISO/TS 80004-1:2010)
Nanotechnologien - Fachwörterverzeichnis - Teil 1: Kernbegriffe (ISO/TS 80004-1:2010)
Nanotechnologies - Vocabulaire - Partie 1: Termes "coeur" (ISO/TS 80004-1:2010)
Ta slovenski standard je istoveten z: CEN ISO/TS 80004-1:2014
ICS:
01.040.07 Matematika. Naravoslovne Mathematics. Natural
vede (Slovarji) sciences (Vocabularies)
07.030 Fizika. Kemija Physics. Chemistry
SIST-TS CEN ISO/TS 80004-1:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST-TS CEN ISO/TS 80004-1:2015

---------------------- Page: 2 ----------------------

SIST-TS CEN ISO/TS 80004-1:2015

TECHNICAL SPECIFICATION
CEN ISO/TS 80004-1

SPÉCIFICATION TECHNIQUE

TECHNISCHE SPEZIFIKATION
December 2014
ICS 07.030; 01.040.07
English Version
Nanotechnologies - Vocabulary - Part 1: Core terms (ISO/TS
80004-1:2010)
Nanotechnologies - Vocabulaire - Partie 1: Termes "coeur" Nanotechnologien - Fachwörterverzeichnis - Teil 1:
(ISO/TS 80004-1:2010) Kernbegriffe (ISO/TS 80004-1:2010)
This Technical Specification (CEN/TS) was approved by CEN on 8 December 2014 for provisional application.

The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.

CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TS 80004-1:2014 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST-TS CEN ISO/TS 80004-1:2015
CEN ISO/TS 80004-1:2014 (E)
Contents Page
Foreword .3
2

---------------------- Page: 4 ----------------------

SIST-TS CEN ISO/TS 80004-1:2015
CEN ISO/TS 80004-1:2014 (E)
Foreword
The text of ISO/TS 80004-1:2010 has been prepared by Technical Committee ISO/TC 229
“Nanotechnologies” of the International Organization for Standardization (ISO) and has been taken over as
CEN ISO/TS 80004-1:2014 by Technical Committee CEN/TC 352 “Nanotechnologies” the secretariat of which
is held by AFNOR.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Croatia, Cyprus,
Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO/TS 80004-1:2010 has been approved by CEN as CEN ISO/TS 80004-1:2014 without any
modification.
3

---------------------- Page: 5 ----------------------

SIST-TS CEN ISO/TS 80004-1:2015

---------------------- Page: 6 ----------------------

SIST-TS CEN ISO/TS 80004-1:2015
TECHNICAL ISO/TS

SPECIFICATION 80004-1

First edition
2010-10-15

Nanotechnologies — Vocabulary —
Part 1:
Core terms
Nanotechnologies — Vocabulaire —
Partie 1: Termes «cœur»





Reference number
ISO/TS 80004-1:2010(E)
©
 ISO 2010

---------------------- Page: 7 ----------------------

SIST-TS CEN ISO/TS 80004-1:2015
ISO/TS 80004-1:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2010
The reproduction of the terms and definitions contained in this International Standard is permitted in teaching manuals, instruction
booklets, technical publications and journals for strictly educational or implementation purposes. The conditions for such reproduction are:
that no modifications are made to the terms and definitions; that such reproduction is not permitted for dictionaries or similar publications
offered for sale; and that this International Standard is referenced as the source document.
With the sole exceptions noted above, no other part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2010 – All rights reserved

---------------------- Page: 8 ----------------------

SIST-TS CEN ISO/TS 80004-1:2015
ISO/TS 80004-1:2010(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Terms and definitions.1
Bibliography.3
Alphabetical index.4

© ISO 2010 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST-TS CEN ISO/TS 80004-1:2015
ISO/TS 80004-1:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
In other circumstances, particularly when there is an urgent market requirement for such documents, a
technical committee may decide to publish other types of document:
— an ISO Publicly Available Specification (ISO/PAS) represents an agreement between technical experts in
an ISO working group and is accepted for publication if it is approved by more than 50 % of the members
of the parent committee casting a vote;
— an ISO Technical Specification (ISO/TS) represents an agreement between the members of a technical
committee and is accepted for publication if it is approved by 2/3 of the members of the committee
casting a vote.
An ISO/PAS or ISO/TS is reviewed after three years in order to decide whether it will be confirmed for a
further three years, revised to become an International Standard, or withdrawn. If the ISO/PAS or ISO/TS is
confirmed, it is reviewed again after a further three years, at which time it must either be transformed into an
International Standard or be withdrawn.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO/TS 80004-1 was prepared jointly by Technical Committee ISO/TC 229, Nanotechnologies, and Technical
Committee IEC/TC 113, Nanotechnology standardization for electrical and electronic products and systems.
The draft was circulated for voting to the national bodies of both ISO and IEC.
Document
...