Gas cylinders - High pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles (ISO 11439:2013)

This International Standard specifies minimum requirements for light-weight refillable gas cylinders intended only for the on-board storage of high pressure compressed natural gas as a fuel for automotive vehicles to which the cylinders are to be fixed. The service conditions do not cover external loadings that can arise from vehicle collisions, etc. This International Standard covers cylinders of any seamless steel, seamless aluminium alloy or nonmetallic material construction, using any design or method of manufacture suitable for the specified service conditions. This International Standard does not cover cylinders of stainless steel. Although this standard uses 200 bar as a reference working pressure, other working pressures can be used. Cylinders covered by this International Standard are designated Type 1, Type 2, Type 3 and Type 4.

Gasflaschen - Hochdruck-Flaschen für die fahrzeuginterne Speicherung von Erdgas als Treibstoff für Kraftfahrzeuge (ISO 11439:2013)

Diese Internationale Norm legt Mindestanforderungen für serienmäßig produzierte wiederbefüllbare Gasflaschen in Leichtbauweise fest. Diese Flaschen sind ausschließlich für die Mitführung von unter hohem Druck verdichtetem Erdgas als Treibstoff für Kraftfahrzeuge, mit denen sie fest verbunden sind, bestimmt. Die Betriebsbedingungen berücksichtigen keine äußeren Belastungen, die als Folge von Fahrzeugzusammen-stößen usw. resultieren können.
Diese Internationale Norm deckt Flaschen beliebiger Konstruktion aus Stahl, Aluminium oder nicht¬metallischen Werkstoffen ab, die nach einer beliebigen Auslegung oder Herstellungsmethode gefertigt sind, die für die festgelegten Betriebsbedingungen geeignet ist. Diese Internationale Norm gilt nicht für Flaschen aus Edelstahl oder geschweißte Flaschenkonstruktionen. Obwohl diese Norm einen Betriebsdruck von 200 bar als Bezugsdruck verwendet, können andere Betriebsdrücke verwendet werden.
Die von dieser Internationale Norm erfassten Flaschen werden folgendermaßen bezeichnet:
Typ 1 -   metallische Flasche
Typ 2 -   metallischer Liner mit Verbund-Verstärkung ausschließlich im zylindrischen Bereich (umfangs-umwickelte Flasche)
Typ 3 -   metallischer Liner mit Belastungsverteilung mit Verbund-Verstärkung im zylindrischen Bereich und in den Enden (vollumwickelte Flasche)
Typ 4 -   nichtmetallischer Liner ohne Belastungsverteilung oder Flasche ohne Liner mit Verbund-Verstärkung im zylindrischen Bereich und in den Enden (vollumwickelte Flasche)
ANMERKUNG   Flaschenauslegungen in Übereinstimmung mit ISO 9809-1, ISO 9809-2, ISO 9809-3 und ISO 7866 können für den Fahrzeugbetrieb verwendet werden, vorausgesetzt, dass diese Auslegungen die in dieser Internationalen Norm festgelegten zusätzlichen Anforderungen erfüllen.

Bouteilles à gaz - Bouteilles haute pression pour le stockage de gaz naturel utilisé comme carburant à bord des véhicules automobiles (ISO 11439:2013)

L'ISO 11439:2013 spécifie les exigences minimales concernant les bouteilles à gaz rechargeables, légères, conçues uniquement pour le stockage de gaz naturel comprimé haute pression, utilisé comme carburant à bord des véhicules automobiles sur lesquels elles sont montées. Les conditions de services ne couvrent pas les charges externes que peuvent provoquer des collisions entre véhicules, etc.
L'ISO 11439:2013 couvre les bouteilles fabriquées en n'importe quel type d'acier sans soudure, d'alliage d'aluminium sans soudure ou de matériau non métallique, de tout type de conception ou méthode de fabrication approprié aux conditions d'utilisation spécifiées. Elle ne couvre pas les bouteilles en acier inoxydable. Bien que la présente Norme internationale utilise une pression de service de référence de 200 bar, d'autres pressions de service peuvent être utilisées.
Les bouteilles couvertes par l'ISO 11439:2013 sont désignées par Type 1, Type 2, Type 3 et Type 4.

Plinske jeklenke - Visokotlačne jeklenke za zemeljski plin za pogon motornih vozil, vgrajene na vozilo (ISO 11439:2013)

Ta mednarodni standard določa minimalne zahteve za lahke ponovno polnljive plinske jeklenke, obvezno vgrajene v vozilo, za visokotlačni stisnjeni zemeljski plin kot gorivo za avtomobilska vozila, v katera se namestijo jeklenke. Pogoji obratovanja ne zajemajo zunanjih obremenitev, ki lahko nastanejo zaradi trka vozil itd. Ta mednarodni standard obravnava jeklenke kakršne koli izdelave iz jekla, aluminijeve zlitine ali nekovinskega materiala, z uporabo kakršnega koli konstruiranja ali metode proizvodnje, primerne za navedene pogoje obratovanja. Ta mednarodni standard ne zajema jeklenk iz nerjavnega jekla. Čeprav je v tem standardu referenčni delovni tlak 200 barov, je mogoče uporabiti tudi druge delovne tlake. Jeklenke iz tega mednarodnega standarda so označene kot tip 1, tip 2, tip 3 in tip 4.

General Information

Status
Published
Public Enquiry End Date
19-May-2012
Publication Date
17-Nov-2013
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
09-Sep-2013
Due Date
14-Nov-2013
Completion Date
18-Nov-2013

Relations

Buy Standard

Standard
EN ISO 11439:2013
English language
80 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 11439:2013
01-december-2013
1DGRPHãþD
SIST EN ISO 11439:2002
3OLQVNHMHNOHQNH9LVRNRWODþQHMHNOHQNH]D]HPHOMVNLSOLQ]DSRJRQPRWRUQLKYR]LO
YJUDMHQHQDYR]LOR ,62
Gas cylinders - High pressure cylinders for the on-board storage of natural gas as a fuel
for automotive vehicles (ISO 11439:2013)
Gasflaschen - Hochdruck-Flaschen für die fahrzeuginterne Speicherung von Erdgas als
Treibstoff für Kraftfahrzeuge (ISO 11439:2013)
Bouteilles à gaz - Bouteilles haute pression pour le stockage de gaz naturel utilisé
comme carburant à bord des véhicules automobiles (ISO 11439:2013)
Ta slovenski standard je istoveten z: EN ISO 11439:2013
ICS:
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
43.060.40 Sistemi za gorivo Fuel systems
SIST EN ISO 11439:2013 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 11439:2013

---------------------- Page: 2 ----------------------

SIST EN ISO 11439:2013


EUROPEAN STANDARD
EN ISO 11439

NORME EUROPÉENNE

EUROPÄISCHE NORM
June 2013
ICS 23.020.30; 43.060.40 Supersedes EN ISO 11439:2000
English Version
Gas cylinders - High pressure cylinders for the on-board storage
of natural gas as a fuel for automotive vehicles (ISO
11439:2013)
Bouteilles à gaz - Bouteilles haute pression pour le Gasflaschen - Hochdruck-Flaschen für die fahrzeuginterne
stockage de gaz naturel utilisé comme carburant à bord Speicherung von Erdgas als Treibstoff für Kraftfahrzeuge
des véhicules automobiles (ISO 11439:2013) (ISO 11439:2013)
This European Standard was approved by CEN on 18 April 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11439:2013: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 11439:2013
EN ISO 11439:2013 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 11439:2013
EN ISO 11439:2013 (E)
Foreword
This document (EN ISO 11439:2013) has been prepared by Technical Committee ISO/TC 58 "Gas cylinders"
in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the secretariat of which is
held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2013, and conflicting national standards shall be withdrawn
at the latest by December 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11439:2000.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11439:2013 has been approved by CEN as EN ISO 11439:2013 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 11439:2013

---------------------- Page: 6 ----------------------

SIST EN ISO 11439:2013
INTERNATIONAL ISO
STANDARD 11439
Second edition
2013-06-01
Gas cylinders — High pressure
cylinders for the on-board storage of
natural gas as a fuel for automotive
vehicles
Bouteilles à gaz — Bouteilles haute pression pour le stockage de gaz
naturel utilisé comme carburant à bord des véhicules automobiles
Reference number
ISO 11439:2013(E)
©
ISO 2013

---------------------- Page: 7 ----------------------

SIST EN ISO 11439:2013
ISO 11439:2013(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 11439:2013
ISO 11439:2013(E)

Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Service conditions . 4
4.1 General . 4
4.2 Maximum pressures . 4
4.3 Design number of filling cycles . 4
4.4 Temperature range . 4
4.5 Gas composition . 5
4.6 External surfaces . 5
5 Inspection and testing . 6
6 Type approval procedure . 6
6.1 General . 6
6.2 Type approval . 6
6.3 Statement of service . 7
6.4 Design data . 7
6.5 Manufacturing data . 8
6.6 Fracture performance and non-destructive examination (NDE) defect size . 8
6.7 Specification sheet . 8
6.8 Additional supporting data . 8
6.9 Type approval certificate. 8
7 Requirements for type 1 metal cylinders . 8
7.1 General . 8
7.2 Materials . 9
7.3 Design Requirements . 9
7.4 Construction and workmanship .10
7.5 Prototype testing procedure .11
7.6 Batch tests .13
7.7 Tests on every cylinder .15
7.8 Batch acceptance certificate .15
7.9 Failure to meet test requirements .15
8 Requirements for type 2 hoop-wrapped cylinders .16
8.1 General .16
8.2 Materials .16
8.3 Design requirements .17
8.4 Construction and workmanship .18
8.5 Prototype testing procedure .20
8.6 Batch tests on liners and cylinders .22
8.7 Tests on every liner and cylinder .25
8.8 Batch acceptance certificate .26
8.9 Failure to meet test requirements .26
9 Requirements for type 3 fully-wrapped cylinders .27
9.1 General .27
9.2 Materials .27
9.3 Design requirements .28
9.4 Construction and workmanship .29
9.5 Prototype testing procedure .31
9.6 Batch tests on liners and cylinders .35
9.7 Tests on every liner and cylinder .36
© ISO 2013 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 11439:2013
ISO 11439:2013(E)

9.8 Batch acceptance certificate .37
9.9 Failure to meet test requirements .37
10 Requirements for type 4 fully-wrapped composite cylinders .38
10.1 General .38
10.2 Materials .38
10.3 Design requirements .38
10.4 Construction and workmanship .39
10.5 Prototype testing procedure .40
10.6 Batch tests .47
10.7 Tests on every cylinder .48
10.8 Batch acceptance certificate .48
10.9 Failure to meet test requirements .49
11 Marking .49
12 Preparation for dispatch .50
Annex A (normative) Test methods and criteria .51
Annex B (normative) Ultrasonic examination .60
Annex C (informative) Non-destructive examination (NDE) defect size by flawed
cylinder cycling .64
Annex D (informative) Report forms .65
Annex E (informative) Standard working pressures .68
Annex F (informative) Verification of stress ratios using strain gauges .69
Annex G (informative) Manufacturer’s instructions for handling, use and inspection
of cylinders .70
iv © ISO 2013 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 11439:2013
ISO 11439:2013(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11439 was prepared by Technical Committee ISO/TC 58, Gas cylinders, Subcommittee SC 3,
Cylinder design.
This second edition cancels and replaces the first edition (ISO 11439:2000), which has been technically
revised. In addition to editorial improvements, the principal technical difference between the first and
second editions is the clarification and alteration of the “Change of Design” requirements for the various
cylinder types.
© ISO 2013 – All rights reserved v

---------------------- Page: 11 ----------------------

SIST EN ISO 11439:2013
ISO 11439:2013(E)

Introduction
Cylinders for the on-board storage of fuel for natural gas vehicle service are required to be light-weight, at
the same time maintaining or improving on the level of safety currently existing for other pressure vessels.
Owners or users of cylinders designed to this International Standard should note that the cylinders are
designed to operate safely if used in accordance with specified service conditions for a specified finite
service life only. The expiry date is marked on each cylinder and it is the responsibility of owners and
users to ensure that cylinders are not used after that date, and that they are inspected in accordance
with the manufacturer’s instructions.
Users of this International Standard are encouraged to consider the environmental impacts associated
with performing certain tests.
vi © ISO 2013 – All rights reserved

---------------------- Page: 12 ----------------------

SIST EN ISO 11439:2013
INTERNATIONAL STANDARD ISO 11439:2013(E)
Gas cylinders — High pressure cylinders for the on-board
storage of natural gas as a fuel for automotive vehicles
1 Scope
This International Standard specifies minimum requirements for light-weight refillable gas cylinders
intended only for the on-board storage of high pressure compressed natural gas as a fuel for automotive
vehicles to which the cylinders are to be fixed. The service conditions do not cover external loadings that
can arise from vehicle collisions, etc.
This International Standard covers cylinders of any seamless steel, seamless aluminium alloy or non-
metallic material construction, using any design or method of manufacture suitable for the specified
service conditions. This International Standard does not cover cylinders of stainless steel. Although this
standard uses 200 bar as a reference working pressure, other working pressures can be used.
Cylinders covered by this International Standard are designated Type 1, Type 2, Type 3 and Type 4.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 148-1, Metallic materials — Charpy pendulum impact test — Part 1: Test method
ISO 306, Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 2808, Paints and varnishes — Determination of film thickness
ISO 6506-1, Metallic materials — Brinell hardness test — Part 1: Test method
ISO 6892-1, Metallic materials — Tensile testing — Part 1: Method of test at room temperature
ISO 7866, Gas cylinders — Refillable seamless aluminium alloy gas cylinders — Design, construction and testing
ISO 9227, Corrosion tests in artificial atmospheres — Salt spray tests
ISO 9712, Non-destructive testing — Qualification and certification of NDT personnel
ISO 9809-1, Gas cylinders — Refillable seamless steel gas cylinders — Design, construction and testing —
Part 1: Quenched and tempered steel cylinders with tensile strength less than 1 100 MPa
ISO 9809-2, Gas cylinders — Refillable seamless steel gas cylinders — Design, construction and testing —
Part 2: Quenched and tempered steel cylinders with tensile strength greater than or equal to 1 100 MPa
ISO 9809-3, Gas cylinders — Refillable seamless steel gas cylinders — Design, construction and testing —
Part 3: Normalized steel cylinders
ISO 14130, Fibre-reinforced plastic composites — Determination of apparent interlaminar shear strength
by short-beam method
ISO 15403-1, Natural gas — Natural gas for use as a compressed fuel for vehicles — Part 1: Designation
of the quality
© ISO 2013 – All rights reserved 1

---------------------- Page: 13 ----------------------

SIST EN ISO 11439:2013
ISO 11439:2013(E)

ISO/TR 15403-2, Natural gas — Natural gas for use as a compressed fuel for vehicles — Part 2: Specification
of the quality
ISO 15500-13, Road vehicles — Compressed natural gas (CNG) fuel system components — Part 13: Pressure
relief device (PRD)
ASTM D522-93a, Standard Test Methods for Mandrel Bend Test of Attached Organic Coatings
ASTM D1308-87, Standard Test Method for Effect of Household Chemicals on Clear and Pigmented
Organic Finishes
ASTM D2794-93, Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid
Deformation (Impact)
ASTM D3170-87, Standard Test Method for Chipping Resistance of Coatings
ASTM D3359, Standard Test Methods for Measuring Adhesion by Tape Test
ASTM D3418, Standard Test Method for Transition Temperatures of Polymers by Differential Scanning
Calorimetry
1)
ASTM G154:2006 , Standard Practice for Operating Fluorescent Light Apparatus for UV Exposure of
Nonmetallic Materials
NACE/TM 0177-96, Laboratory Testing of Metals for Resistance to Sulfide Stress Cracking and Stress
Corrosion Cracking in H2S Environments
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
authorized inspection body
authorized inspection body, approved or recognized by the regulatory authority of the user country,
for the supervision of construction and testing of cylinders used for the on-board storage of natural gas
3.2
autofrettage
pressure application procedure used in manufacturing composite cylinders with metal liners, which
strains the liner past its yield point sufficient to cause permanent plastic deformation
3.3
autofrettage pressure
pressure within the overwrapped cylinder at which the required distribution of stresses between the
liner and the overwrap is established
3.4
batch – composite cylinders
group of not more than 200 cylinders plus cylinders for destructive testing, or if greater, one shift of
successive production of cylinders, successively produced from qualified liners having the same size,
design, specified materials of construction and process of manufacture
3.5
batch – metal cylinders/liners
group of not more than 200 cylinders/liners plus cylinders/liners for destructive testing, or if greater,
one shift of successive production of metal cylinders/liners, successively produced having the same
nominal diameter, wall thickness, design, specified material of construction, material cast, process of
manufacture, equipment for manufacture and heat treatment, and conditions of time, temperature and
atmosphere during heat treatment
1) Most recent version is ASTM G154-12a, 2012.
2 © ISO 2013 – All rights reserved

---------------------- Page: 14 ----------------------

SIST EN ISO 11439:2013
ISO 11439:2013(E)

3.6
batch – non-metallic liners
group of not more than 200 liners plus liners for destructive testing, or if greater, one shift of successive
production of non-metallic liners, successively produced having the same nominal diameter, wall
thickness, design, specified material of construction and process of manufacture
3.7
burst pressure
highest pressure reached in a cylinder during a burst test
3.8
composite cylinder
cylinder made of resin-impregnated continuous filament wound over a metallic or non-metallic liner
3.9
destroyed
cylinder in a state of alteration which makes it physically unusable for its purp
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.