SIST ISO 11312:2003
(Main)Photography -- Sheets of sensitized material for the pre-press industry -- Dimensions and related requirements
Photography -- Sheets of sensitized material for the pre-press industry -- Dimensions and related requirements
This International Standard applies to sheets of photographic sensitized materials for use in the pre-press industry.
It specifies dimensions and package marking of sensitized materials including those for electronic scanners.
Photographie -- Feuilles en matériau sensible pour l'industrie de préimpression -- Dimensions et exigences connexes
Photography -- Sheets of sensitized material for the pre-press industry -- Dimensions and related requirements
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 11312
Second edition
2000-11-01
Photography — Sheets of sensitized
material for the pre-press industry —
Dimensions and related requirements
Photographie — Feuilles en matériau sensible pour l'industrie de
préimpression — Dimensions et exigences connexes
Reference number
ISO 11312:2000(E)
©
ISO 2000
---------------------- Page: 1 ----------------------
ISO 11312:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 11312:2000(E)
Contents Page
Foreword.iv
Introduction.v
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 Conditions for measurement of dimensions .2
5 Dimensions.2
6 Squareness and edge straightness .4
7 Identification of the sensitized side.4
8 Package marking .4
9 Compliance.5
Annex A (informative) Dimensional stability .6
Bibliography.7
© ISO 2000 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 11312:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 11312 was prepared by Technical Committee ISO/TC 42, Photography.
This second edition cancels and replaces the first edition (ISO 11312:1993, Photography — Film dimensions —
Film for electronic scanner use) and ISO 6407:1992, Photography — Film dimensions — Graphic arts, featuring a
new emphasis on general cutting rules as opposed to listing all known sizes specifically. New definitions have been
added to assist the reader.
Annex A of this International Standard is for information only.
iv © ISO 2000 – All rights reserved
---------------------- Page: 4 ----------------------
ISO 11312:2000(E)
Introduction
This International Standard replaces a number of standards relating to sheets of sensitized material for the pre-
press industry. It features a simplified set of rules for dimensioning new sizes. It is hoped that the use of this
International Standard will promote the compatibility of sensitized material and equipment.
© ISO 2000 – All rights reserved v
---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 11312:2000(E)
Photography — Sheets of sensitized material for the pre-press
industry — Dimensions and related requirements
1 Scope
This International Standard applies to sheets of photographic sensitized materials for use in the pre-press industry.
It specifies dimensions and package marking of sensitized materials including those for electronic scanners.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.
ISO 1:1975, Standard reference temperature for industrial length measurements.
ISO 216:1975, Writing paper and certain classes of printed matter — Trimmed sizes — A and B series.
ISO 554:1976, Standard atmospheres for conditioning and/or testing — Specifications.
3 Terms and definitions
For the purposes of this International Standard, the following terms and definitions apply.
3.1
pre-press
that part of the printing or publishing process preceding preparation of a printing plat
...
SLOVENSKI STANDARD
SIST ISO 11312:2003
01-april-2003
Photography -- Sheets of sensitized material for the pre-press industry --
Dimensions and related requirements
Photography -- Sheets of sensitized material for the pre-press industry -- Dimensions
and related requirements
Photographie -- Feuilles en matériau sensible pour l'industrie de préimpression --
Dimensions et exigences connexes
Ta slovenski standard je istoveten z: ISO 11312:2000
ICS:
37.040.20 )RWRJUDIVNLSDSLUILOPLLQ Photographic paper, films
IRWRJUDIVNHSORãþH)LOPVNL and cartridges
]YLWNL
SIST ISO 11312:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ISO 11312:2003
---------------------- Page: 2 ----------------------
SIST ISO 11312:2003
INTERNATIONAL ISO
STANDARD 11312
Second edition
2000-11-01
Photography — Sheets of sensitized
material for the pre-press industry —
Dimensions and related requirements
Photographie — Feuilles en matériau sensible pour l'industrie de
préimpression — Dimensions et exigences connexes
Reference number
ISO 11312:2000(E)
©
ISO 2000
---------------------- Page: 3 ----------------------
SIST ISO 11312:2003
ISO 11312:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved
---------------------- Page: 4 ----------------------
SIST ISO 11312:2003
ISO 11312:2000(E)
Contents Page
Foreword.iv
Introduction.v
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 Conditions for measurement of dimensions .2
5 Dimensions.2
6 Squareness and edge straightness .4
7 Identification of the sensitized side.4
8 Package marking .4
9 Compliance.5
Annex A (informative) Dimensional stability .6
Bibliography.7
© ISO 2000 – All rights reserved iii
---------------------- Page: 5 ----------------------
SIST ISO 11312:2003
ISO 11312:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 11312 was prepared by Technical Committee ISO/TC 42, Photography.
This second edition cancels and replaces the first edition (ISO 11312:1993, Photography — Film dimensions —
Film for electronic scanner use) and ISO 6407:1992, Photography — Film dimensions — Graphic arts, featuring a
new emphasis on general cutting rules as opposed to listing all known sizes specifically. New definitions have been
added to assist the reader.
Annex A of this International Standard is for information only.
iv © ISO 2000 – All rights reserved
---------------------- Page: 6 ----------------------
SIST ISO 11312:2003
ISO 11312:2000(E)
Introduction
This International Standard replaces a number of standards relating to sheets of sensitized material for the pre-
press industry. It features a simplified set of rules for dimensioning new sizes. It is hoped that the use of this
International Standard will promote the compatibility of sensitized material and equipment.
© ISO 2000 – All rights reserved v
---------------------- Page: 7 ----------------------
SIST ISO 11312:2003
---------------------- Page: 8 ----------------------
SIST ISO 11312:2003
INTERNATIONAL STANDARD ISO 11312:2000(E)
Photography — Sheets of sensitized material for the pre-press
industry — Dimensions and related requirements
1 Scope
This International Standard applies to sheets of photographic sensitized materials for use in the pre-press industry.
It specifies dimensions and package marking of sensitized materials including those for electronic scanners.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registe
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.