SIST EN IEC 62386-105:2020

SLOVENSKI STANDARD
SIST EN IEC 62386-105:2020
01-julij-2020
Digitalni naslovljivi vmesnik za razsvetljavo - 105. del: Posebne zahteve za krmilja
in krmilne naprave - Prenos strojne programske opreme (IEC 62386-105:2020)
Digital addressable lighting interface - Part 105: Particular requirements for control gear
and control devices - Firmware Transfer (IEC 62386-105:2020)
Digital adressierbare Schnittstelle für die Beleuchtung - Teil 105: Besondere
Anforderungen für Betriebs- und Steuergeräte - Firmware Übertragung (IEC 62386-
105:2020)
Interface d'éclairage adressable numérique - Partie 105: Exigences particulières pour
appareillages et dispositifs de commande - Transfert du microprogramme (IEC 62386-
105:2020)
Ta slovenski standard je istoveten z: EN IEC 62386-105:2020
ICS:
29.140.50 Instalacijski sistemi za Lighting installation systems
razsvetljavo
35.200 Vmesniška in povezovalna Interface and interconnection
oprema equipment
SIST EN IEC 62386-105:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 62386-105:2020

---------------------- Page: 2 ----------------------
SIST EN IEC 62386-105:2020


EUROPEAN STANDARD EN IEC 62386-105

NORME EUROPÉENNE

EUROPÄISCHE NORM
May 2020
ICS 29.140.50; 29.140.99

English Version
Digital addressable lighting interface - Part 105: Particular
requirements for control gear and control devices - Firmware
Transfer
(IEC 62386-105:2020)
Interface d'éclairage adressable numérique - Partie 105: Digital adressierbare Schnittstelle für die Beleuchtung - Teil
Exigences particulières pour appareillages et dispositifs de 105: Besondere Anforderungen für Betriebs- und
commande - Transfert du microprogramme Steuergeräte - Firmware Übertragung
(IEC 62386-105:2020) (IEC 62386-105:2020)
This European Standard was approved by CENELEC on 2020-04-30. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 62386-105:2020 E

---------------------- Page: 3 ----------------------
SIST EN IEC 62386-105:2020
EN IEC 62386-105:2020 (E)
European foreword
The text of document 34/675/FDIS, future edition 1 of IEC 62386-105, prepared by IEC/TC 34
"Lighting" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN IEC 62386-105:2020.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-01-30
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-04-30
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 62386-105:2020 was approved by CENELEC as a
European Standard without any modification.


2

---------------------- Page: 4 ----------------------
SIST EN IEC 62386-105:2020
EN IEC 62386-105:2020 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 62386-101 2014 Digital addressable lighting interface - Part 101: EN 62386-101 2014
General requirements - System components
+ A1 2018 + A1 2018
IEC 62386-102 2014 Digital addressable lighting interface - Part 102: EN 62386-102 2014
General requirements - Control gear
+ A1 2018 + A1 2018
IEC 62386-103 2014 Digital addressable lighting interface - Part 103: EN 62386-103 2014
General requirements - Control devices
+ A1 2018 + A1 2018

3

---------------------- Page: 5 ----------------------
SIST EN IEC 62386-105:2020

---------------------- Page: 6 ----------------------
SIST EN IEC 62386-105:2020




IEC 62386-105

®


Edition 1.0 2020-03




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE
colour

inside










Digital addressable lighting interface – –

Part 105: Particular requirements for control gear and control devices –

Firmware transfer




Interface d’éclairage adressable numérique – –

Partie 105: Exigences particulières pour appareillages et dispositifs de


commande – Transfert du microprogramme













INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 29.140.50; 29.140.99 ISBN 978-2-8322-8020-1




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------
SIST EN IEC 62386-105:2020
– 2 – IEC 62386-105:2020 © IEC 2020
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 7
4 General . 8
4.1 General . 8
4.2 Transmitters and receivers in bus units . 8
4.3 Logical units in a bus unit . 8
5 Electrical specification . 8
6 Interface power supply . 8
7 Transmission protocol structure . 8
7.1 General . 8
7.2 32 bit forward frame encoding . 9
8 Timing . 9
9 Method of operation . 9
9.1 General . 9
9.2 Data transmission . 9
9.3 Duration . 9
9.4 Security . 10
9.5 Firmware update features . 10
9.6 Update process . 10
9.6.1 Start firmware update . 10
9.6.2 Data transfer . 10
9.6.3 Persistent variables during firmware update . 12
9.6.4 Firmware version number . 13
9.6.5 Firmware update in a system . 13
9.6.6 Error recovery. 13
10 Declaration of variables . 13
11 Definition of commands . 14
11.1 General . 14
11.2 Overview sheets . 14
11.3 Commands . 16
11.3.1 General . 16
11.3.2 Standard commands . 16
11.3.3 Data transfer commands . 17
Annex A (normative) Update file description . 19
Annex B (normative) CRC16 Calculation . 20
Annex C (informative) Firmware update process example . 21
Annex D (informative) Firmware update management check sheet . 23

Figure 1 – IEC 62386 graphical overview . 6
Figure C.1 – Example of a firmware update process . 21

---------------------- Page: 8 ----------------------
SIST EN IEC 62386-105:2020
IEC 62386-105:2020 © IEC 2020 – 3 –
Table 1 – 32-bit command frame encoding . 9
Table 2 – Firmware update features . 10
Table 3 – Block 0 definitions . 11
Table 4 – Block 1.n definitions . 12
Table 5 – Declaration of additional variables . 14
Table 6 – Standard commands for bus units with firmware update capability . 15
Table 7 – Data transfer commands for bus units with firmware update capability . 15

---------------------- Page: 9 ----------------------
SIST EN IEC 62386-105:2020
– 4 – IEC 62386-105:2020 © IEC 2020
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

DIGITAL ADDRESSABLE LIGHTING INTERFACE –

Part 105: Particular requirements for control gear and control devices –
Firmware transfer

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC
Publication(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62386-105 has been prepared by IEC technical committee 34:
Lamps and related equipment.
The text of this International Standard is based on the following documents:
FDIS Report on voting
34/675/FDIS 34/688/RVD

Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 10 ----------------------
SIST EN IEC 62386-105:2020
IEC 62386-105:2020 © IEC 2020 – 5 –
This Part 105 of IEC 62386 is intended to be used in conjunction with:
• Part 101, which contains general requirements for system components;
• Part 102, which contains general requirements for the relevant product type (control gear),
and with the appropriate Parts 2xx (particular requirements for control gear);
• Part 103, which contains general requirements for the relevant product type (control
devices), and the appropriate Parts 3xx (particular requirements for control devices).
A list of all parts in the IEC 62386 series, published under the general title Digital addressable
lighting interface, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.

---------------------- Page: 11 ----------------------
SIST EN IEC 62386-105:2020
– 6 – IEC 62386-105:2020 © IEC 2020
INTRODUCTION
IEC 62386 contains several parts, referred to as series. The IEC 62386 series specifies a bus
system for control by digital signals of electronic lighting equipment. The IEC 62386-1xx
series includes the basic specifications. Part 101 contains general requirements for system
components, Part 102 extends this information with general requirements for control gear and
Part 103 extends it further with general requirements for control devices.
The IEC 62386-2xx series extends the general requirements for control gear with lamp
specific extensions (mainly for backward compatibility with Edition 1 of IEC 62386) and with
control gear specific features.
The IEC 62386-3xx series extends the general requirements for control devices with input
device specific extensions describing the instance types as well as some common features
that can be combined with multiple instance types.
This first edition of IEC 62386-105 is intended to be used in conjunction with IEC 62386-101,
IEC 62386-102 and the various parts that make up the IEC 62386-2xx series for control gear,
together with IEC 62386-103 and the various parts that make up the IEC 62386-3xx series of
particular requirements for control devices. The division into separately published parts
provides for ease of future amendments and revisions. Additional requirements will be added
as and when a need for them is recognized.
The setup of the standards is graphically represented in Figure 1 below.

Figure 1 – IEC 62386 graphical overview
When this part of IEC 62386 refers to any of the clauses of the IEC 62386-1xx series, the
extent to which such a clause is applicable and the order in which the tests are to be
performed are specified. The other parts also include additional requirements, as necessary.
All numbers used in this document are decimal numbers unless otherwise noted. Hexadecimal
numbers are given in the format 0xVV, where VV is the value. Binary numbers are given in
the format XXXXXXXXb or in the format XXXX XXXX, where X is 0 or 1, "x" in binary numbers
means "don't care".
The following typographic expressions are used:
Variables: variableName or variableName[3:0], giving only bits 3 to 0 of variableName
Range of values: [lowest, highest]
Command: “COMMAND NAME”

---------------------- Page: 12 ----------------------
SIST EN IEC 62386-105:2020
IEC 62386-105:2020 © IEC 2020 – 7 –
DIGITAL ADDRESSABLE LIGHTING INTERFACE –

Part 105: Particular requirements for control gear and control devices –
Firmware transfer



1 Scope
This part of IEC 62386 applies to control gear and control devices.
Typically, a bus unit according to IEC 62386 (all parts) contains firmware. There are
circumstances where it might be necessary to change the firmware after production or
shipping of the product. For example if the bus unit does not operate as intended. In such a
case, a firmware update of a bus unit via the interface is beneficial.
This firmware update process is primarily designed to be a bug fix process, not a feature
extension process. Nevertheless the firmware update process can be used for feature
extensions. But it is important that the risk of negative effects to the complete system is
considered in detail.
NOTE Annex D provides a “Firmware update management check sheet” to support risk estimation.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition
cited applies. For undated references, the latest edition of the referenced document (including
any amendments) applies.
IEC 62386-101:2014, Digital addressable lighting interface – Part 101: General requirements
– System components
IEC 62386-101:2014/AMD1:2018
IEC 62386-102:2014, Digital addressable lighting interface – Part 102: General requirements
– Control gear
IEC 62386-102:2014/AMD1:2018
IEC 62386-103:2014, Digital addressable lighting interface – Part 103: General requirements
– Control devices
IEC 62386-103:2014/AMD1:2018
3 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 62386-101,
IEC 62386-102 and IEC 62386-103 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp

---------------------- Page: 13 ----------------------
SIST EN IEC 62386-105:2020
– 8 – IEC 62386-105:2020 © IEC 2020
3.1
firmware
FW
software programmed into a control gear or control device, which can be changed during an
update
Note 1 to entry: This note applies to the French language only.
3.2
CRC
cyclic redundancy check
checksum used to prevent data corruption
Note 1 to entry: Annex B provides detailed information about CRC calculation.
4 General
4.1 General
The requirements of IEC 62386-101:2014 and IEC 62386-101:2014/AMD1:2018 apply, with
the restrictions, changes and additions identified below.
NOTE Systems with a single-master application controller are unlikely to operate correctly when other master
control devices, such as upgrade tools, are connected.
4.2 Transmitters and receivers in bus units
The requirements of IEC 62386-101:2014 and IEC 62386-101:2014/AMD1:2018, 4.6.1 shall
be extended as follows.
Bus units supporting firmware transfer shall be additionally capable of receiving 32 bit forward
frames as specified in IEC 62386-101:2014, 7.4.3 (Reserved forward frame).
4.3 Logical units in a bus unit
If the firmware update process is started on a bus unit, all logical units inside the bus unit
shall be affected. All variables defined in Table 5 shall be shared by all logical units of the bus
unit.
5 Electrical specification
The requirements of IEC 62386-101:2014 and IEC 62386-101:2014/AMD1:2018, Clause 5
apply.
6 Interface power supply
The requirements of IEC 62386-101:2014 and IEC 62386-101:2014/AMD1:2018, Clause 6
apply.
7 Transmission protocol structure
7.1 General
The requirements of IEC 62386-101:2014, Clause 7 apply, with the following additions.

---------------------- Page: 14 ----------------------
SIST EN IEC 62386-105:2020
IEC 62386-105:2020 © IEC 2020 – 9 –
7.2 32 bit forward frame encoding
The forward frame format used for firmware update consists of n = 32 data bits as described
in IEC 62386-101:2014, 7.4.3 (Reserved forward frame).
The 32 bit forward frame for 32 bit frames shall be encoded as shown in Table 1.
Table 1 – 32-bit command frame encoding
Bytes/Bits
Opcode byte
Device addressing
Address byte
method
1 2 3
a
31 30 29 28 27 26 25 24 23…16 15…8 7…0
0 64 short addresses x Short addressing
1 1 1 1 1 1 0 x Broadcast unaddressed
1 1 1 1 1 1 1 x Broadcast
All other address byte values.  Reserved
a
For bit 24, 0 indicates address space for control gear, 1 indicates address space for control
devices.

8 Timing
The requirements of IEC 62386-101:2014 and IEC 62386-101:2014/AMD1:2018, Clause 8
apply.
9 Method of operation
9.1 General
The requirements of IEC 62386-101:2014 and IEC 62386-101:2014/AMD1:2018, 9.8 (Dealing
with frames and commands), 9.2 (Transactions) with the exception that the total duration may
exceed 400 ms, 9.4 (Command iteration) and 9.6 (Use of multiple bus power supplies) apply.
9.2 Data transmission
A bus unit receives a new FW block by block. The first block (block 0) contains information
about the type of bus unit (see Table 3), which receives a new FW. This avoids transferring
the wrong FW to a bus unit if more than one bus unit is updated at a time.
NOTE Annex A provides detailed information about the update file.
The opcode byte 1 shall be 0xFB for 32-bit standard commands (see Table 6). If the opcode
byte 1 in a standard command is not equal to 0xFB, the bus unit shall not accept the standard
command.
9.3 Duration
A data transmission frame consists of a start bit, 32 data bits and a stop condition, which
occupies the bus for around 30 ms. With a settling time of less than 15 ms (maximum frame
priority) the transmission of three bytes takes less than 45 ms. For an update of 64 kByte it is
expected to take less than 20 min.

---------------------- Page: 15 ----------------------
SIST EN IEC 62386-105:2020
– 10 – IEC 62386-105:2020 © IEC 2020
9.4 Security
It is recommended that the individual manufacturer ensures firmware image integrity and
authenticity. This document specifies the use of CRC checksums to help ensure error-free
transfer of data.
9.5 Firmware update features
Each bus unit shall expose its firmware update features as a combination of device properties
as given in Table 2.
Table 2 – Firmware update features
Bit Description Value See
0 “fwUpdateCancelSupported” is TRUE? "1" = "YES" XXX
1-7 Reserved – not implemented "0" = "NO"

The bus unit firmware update features can be queried using
QUERY FW UPDATE FEATURES.
If the bus unit supports cancellation of the firmware update process (see 9.6.2.3),
“fwUpdateCancelSupported” is set to TRUE.
9.6 Update process
9.6.1 Start firmware update
A bus unit shall enable the firmware update process by the acceptance of the command
START FW TRANSFER. Several bus units can be addressed in this way to update more than
one bus unit at a time.
NOTE 1 Annex C provides an example of the firmware update process.
It is recommended not to trigger erasing of the memory before block 0 is verified.
Whilst “fwUpdateProcessEnabled” is TRUE, the operation of the bus unit is manufacturer-
specific except for the requirements given in this document.
NOTE 2 This includes, for example, the reaction to commands of other parts of the IEC 62386 series.
9.6.2 Data transfer
9.6.2.1 Block 0 (information block)
Block 0 contains all data for the bus unit to decide if it will accept the new firmware or not.
The GTIN number, the hardware version number and the firmware version number contained
in the bus unit are described in IEC 62386-102:2014 and IEC 62386-102:2014/AMD1:2018,
9.10.6 (Memory bank 0 for control gear) and IEC 62386-103:2014 and IEC 62386-
103:2014/AMD1:2018, 9.10.6 (Memory bank 0 for control devices). A bus unit shall have a
maximum of one family GTIN which shall be shown in the documentation of the bus unit.
Upon reception of a complete block 0, the following information is checked, where Table 3
shows block 0 content:
• The received block 0 “Size of block” is equal to the value shown in Table 3.
• The received block 0 “Block 0 version” is equal to the value shown in Table 3.

---------------------- Page: 16 ----------------------
SIST EN IEC 62386-105:2020
IEC 62386-105:2020 © IEC 2020 – 11 –
• The received block 0 “GTIN” matches the GTIN stored in memory bank 0.
• (Received block 0 “FW version min”) ≤ (memory bank 0, Firmware version) ≤ (received
block 0 “FW version max”).
• (Received block 0 “HW version min”) ≤ (memory bank 0, Hardware version) ≤ (received
block 0 “HW version max”).
• (Received block 0 “Identification number min”) ≤ (memory bank 0, Identification number) ≤
(received block 0 “Identification number max
...