SIST EN 170100:2002

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Sectional specification: Waveguide type dielectric resonatorsRahmenspezifikation: Dielektrische Resonatoren vom WellenleitertypSpécification intermédiaire: Résonateurs diélectriques à modes guidésSectional Specification: Waveguide type dielectric resonators31.140Piezoelectric and dielectric devicesICS:Ta slovenski standard je istoveten z:EN 170100:2001SIST EN 170100:2002en01-september-2002SIST EN 170100:2002SLOVENSKI
STANDARD



SIST EN 170100:2002



EUROPEAN STANDARDEN 170100NORME EUROPÉENNEEUROPÄISCHE NORMAugust 2001CENELECEuropean Committee for Electrotechnical StandardizationComité Européen de Normalisation ElectrotechniqueEuropäisches Komitee für Elektrotechnische NormungCentral Secretariat: rue de Stassart 35, B - 1050 Brussels© 2001 CENELEC -All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.Ref. No. EN 170100:2001 EICS 31.140English versionSectional Specification:Waveguide type dielectric resonatorsSpécification intermédiaire:Résonateurs diélectriques àmodes guidésRahmenspezifikation:Dielektrische Resonatoren vomWellenleitertypThis European Standard was approved by CENELEC on 2000-08-01. CENELEC members are bound tocomply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving thisEuropean Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning such national standards may be obtained onapplication to the Central Secretariat or to any CENELEC member.This European Standard exists in three official versions (English, French, German). A version in anyother language made by translation under the responsibility of a CENELEC member into its ownlanguage and notified to the Central Secretariat has the same status as the official versions.CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway,Portugal, Spain, Sweden, Switzerland and United Kingdom.SIST EN 170100:2002



EN 170100:2001- 2 -ForewordThis European Standard was prepared by the Technical Committee CENELEC TC 49,Piezoelectric devices for frequency control and selection.The text of the draft was submitted to the Unique Acceptance Procedure and was approved byCENELEC as EN 170100 on 2000-08-01.The following dates were fixed:-latest date by which the EN has to be implementedat national level by publication of an identicalnational standard or by endorsement(dop)2002-02-01-latest date by which the national standards conflictingwith the EN have to be withdrawn(dow)2003-08-01Annexes designated "normative" are part of the body of the standard.In this standard, annexes A, B and C are normative._____________SIST EN 170100:2002



- 3 -EN 170100:2001CONTENTS1 Scope.42General preferred ratings and guidance of detail specifications.42.1Related documents .42.2Preferred ratings and characteristics.42.3Information to be prescribed in detail specifications.43 Capability approval.53.1 Eligibility for capability approval.53.2 Structural similarity.53.3 Procedures for capability approval.53.4Description of capability.63.5Capability Qualifying Components (CQCs.73.6Inspection requirements for CQC's.73.7Programme for capability approval.83.8Capability approval report.83.9Abstract of description of capability.83.10Modifications likely to affect capability approval.83.11Initial capability approval.83.12Maintenance of capability approval.143.13Rework and repair work.153.14Quality conformance inspection.153.15Screening procedures.164Text and measurement procedures.16Annex AExample layout of an abstract of description of capabilityfor inclusion in CECC 00 200.17Annex BLayout of the front page of a CQC specificationfor process control.18Annex CLayout of the front page of a CQC specificationto demonstrate a boundary or limit.19SIST EN 170100:2002



EN 170100:2001- 4 -1ScopeThis sectional specification applies to waveguide type dielectric resonators as custom builtproducts or as standard catalogue items whose quality is assessed on the basis of capabilityapproval.It prescribes the preferred ratings and characteristics with the appropriate tests and measuringmethods contained in the generic specification EN 170000, and gives the general performancerequirements to be used in detail specifications for waveguide type dielectric resonators.The concept of preferred values is in general directly applicable to standard catalogue items butdoes not necessarily apply to custom built products.2General, preferred ratings and guidance on detail specifications2.1Related documentsEN 60068-1Environmental testing - Part 1: General and guidance(IEC 60068-1)EN 170000Generic specification:
Waveguide type dielectric resonators.CECC 00016Basic requirements for the use of Statistical Process Control (SPC) inthe CECC system.NOTE
The above references apply to the current editions except for EN 60068-1 for which the referred edition andthe applicable test clauses defined in EN 170000 shall be used.2.2Preferred ratings and characteristicsThe values given in detail specifications shall preferably be selected from those stated in 2.4 ofthe generic specification EN 170000.2.3Information to be prescribed in detail specifications(for both custom built and standard catalogue items)Guidance on the preparation of detail specifications is given in the blank detail specification.Each detail specification shall state all the tests and measurements required for inspection.
Forstandard catalogue items this shall, as a minimum, include the relevant tests given in the blankdetail specification, with methods and severities.The following information shall be given in each detail specification.2.3.1Outline drawing and dimensionsThe detail specification shall include a dimensional drawing of the waveguide type dielectricresonator and/or reference to an appropriate international standard, to permit easy recognitionand to provide information for dimensioning and gauging procedures.The dimensions shall include the overall dimensions of the body of the component and the sizeand spacing of the terminations.
All dimensions shall be stated in mm.SIST EN 170100:2002



- 5 -EN 170100:20012.3.2MarkingThe detail specification shall prescribe the content of the marking on the waveguide typedielectric resonator primary package in accordance with 2.5 of EN 170000.2.3.3Ordering informationThe detail specification shall prescribe that the following information is required when ordering awaveguide type dielectric resonator.a)Quantityb)Detail specification number, issue number and dateand where applicablec)Nominal frequency in MHz or GHzd) Full description of any additional requirements to identify the waveguide type dielectricresonator.2.3.4Additional information (not for inspection purposes)The detail specification may include information which is not normally required to be verified bythe inspection procedure, such as circuit diagrams, curves, drawings and notes needed forclarification.3Capability approval3.1Eligibility for capability approvalPrior to making an application for capability approval a manufacturer shall first obtainmanufacturer’s inspection approval in accordance with EN 100114-1.The primary stage of manufacture shall be as defined in 3.1 of the generic specificationEN 170000.3.2Structural similarityStructural similarity is not applicable to Capability Approval.
However, it is applicable to releasedlots as defined in 3.14.1 of this specification.3.3Procedures for capability approval3.3.1GeneralCapability approval in waveguide type dielectric resonator technology covers:-the complete design, material preparation and manufacturing techniques, including controlprocedures and tests;-the performance limits claimed for the processes and products, that is those specified for theCapability Qualifying Components (CQCs);-the range of mechanical structures for which approval is granted.SIST EN 170100:2002



EN 170100:2001- 6 -3.3.2Application for capability approvalIn order to obtain capability approval the manufacturer shall apply the rules of procedure given in2.4 of CECC 00 114-3.In an application for capability approval the manufacturer shall define the boundaries of thecapability for which approval is sought in accordance with 3.5.3.3.3Granting of capability approvalCapability approval shall be granted when the manufacturer has:-prepared a capability manual describing the capability for which he wishes to be approved, tothe satisfaction of the ONS;-agreed with the ONS the range of CQCs, as defined in 2.7 of
CECC 00 114-3, to be used forthe assessment of capability;-successfully demonstrated that he can design and manufacture components which satisfy therequirements of this sectional specification, within the limits of
his capability;-prepared a capability approval test report to the satisfaction of the ONS.3.4Description of capabilityThe manufacturer shall prepare a manual describing his capability (see 2.5 of CECC 00 114-3), inrelation to the technologies involved.The manual shall be approved by the ONS who shall ensure that it is a true and complete recordof procedures carried out by the manufacturer during the design, production, testing, inspectionand release of his products.
The manual is a document that shall be treated as 'commercial inconfidence'.The manual shall include the following as a minimum:-A general introduction and description of the technologies involved;-Aspects of customer liaison including provision of design rules (if appropriate) and assistanceto customers in the formulation of their requirements;-A detailed description of the design rules to be used;-The procedure for checking that the design rules are complied with for waveguide typedielectric resonators manufactured to a detail specification;-A list of all materials used, with references to the corresponding purchasing specifications andgoods inward inspection;-A flow chart for the total process showing quality control points and permitted rework loops andcontaining references to all process and quality control procedures which may invokeSPC procedures (see CECC 00 016);-A declaration of processes for which approval has been sought in accordance with 3.5.1;-A declaration of boundaries for which approval has been sought in accordance with 3.5.2;-A list of CQCs used to assess the capability, with a general description of each, supported bya detailed table showing where the declared boundaries of capability are demonstrated by aparticular CQC design;-A detail specification for each CQC.
These shall be produced to the satisfaction of the ONS.(see annexes B and C).SIST EN 170100:2002



- 7 -EN 170100:20013.5Capability Qualifying Components (CQCs)The manufacturer shall agree with the ONS the range of capability qualifying components,selected in accordance with the general plan (see 3.11.2) specified in the capability manual.The CQCs shall comply with the following requirements:a)The range of CQCs used shall cover all the processes, component types and limits of thedeclared capabilityb)The CQCs shall be one of the following:-waveguide type dielectric resonators in production;-test pieces designed for assessment of a process or range of processes;-a combination of both of these.When CQCs are designed and produced solely for capability approval, the manufacturer shallsatisfy the
...